Time

From ArchWiki
(Redirected from Hwclock)
Jump to: navigation, search

Tango-view-fullscreen.pngThis article or section needs expansion.Tango-view-fullscreen.png

Reason: This article mostly documents systemd timedatectl; explain basic commands like date and hwclock first (Discuss in Talk:Time#)

In an operating system, the time (clock) is determined by four parts: time value, time standard, time zone, and Daylight Saving Time (DST) if applicable. This article explains what they are and how to read/set them. Two clocks are present on systems: a hardware clock and a system clock which are also detailed in this article.

Standard behavior of most operating systems is:

  • Set the system clock from the hardware clock on boot.
  • Keep accurate time of the system clock, see #Time synchronization.
  • Set the hardware clock from the system clock on shutdown.

Hardware clock

Tango-view-fullscreen.pngThis article or section needs expansion.Tango-view-fullscreen.png

Reason: How to read, set hardware clock, etc. (Discuss in Talk:Time#)

The hardware clock (a.k.a. the Real Time Clock (RTC) or CMOS clock) stores the values of: Year, Month, Day, Hour, Minute, and Seconds. It does not have the ability to store the time standard (localtime or UTC), nor whether DST is used.

Read hardware clock

# hwclock --show

Set hardware clock from system clock

The following sets the hardware clock from the system clock. Additionally it updates /etc/adjtime or creates it if not present. See hwclock(8) section "The Adjtime File" for more information on this file as well as the #Time skew section.

# hwclock --systohc

System clock

The system clock (a.k.a. the software clock) keeps track of: time, time zone, and DST if applicable. It is calculated by the Linux kernel as the number of seconds since midnight January 1st 1970, UTC. The initial value of the system clock is calculated from the hardware clock, dependent on the contents of /etc/adjtime. After boot-up has completed, the system clock runs independently of the hardware clock. The Linux kernel keeps track of the system clock by counting timer interrupts.

Read clock

To check the current system clock time (presented both in local time and UTC) as well as the RTC (hardware clock):

$ timedatectl

Set system clock

To set the local time of the system clock directly:

# timedatectl set-time "yyyy-MM-dd hh:mm:ss"

For example:

# timedatectl set-time "2014-05-26 11:13:54"

sets the time to May 26th, year 2014, 11:13 and 54 seconds.

Time standard

There are two time standards: localtime and Coordinated Universal Time (UTC). The localtime standard is dependent on the current time zone, while UTC is the global time standard and is independent of time zone values. Though conceptually different, UTC is also known as GMT (Greenwich Mean Time).

The standard used by the hardware clock (CMOS clock, the BIOS time) is set by the operating system. By default, Windows uses localtime, macOS uses UTC, and UNIX-like systems vary. An OS that uses the UTC standard will generally consider the hardware clock as UTC and make an adjustment to it to set the OS time at boot according to the time zone.

If multiple operating systems are installed on a machine, they will all derive the current time from the same hardware clock: it is recommended to adopt a unique standard for the hardware clock to avoid conflicts across systems and set it to UTC. Otherwise, if the hardware clock is set to localtime, more than one operating system may adjust it after a DST change for example, thus resulting in an over-correction; problems may also arise when traveling between different time zones and using one of the operating systems to reset the system/hardware clock.

The hardware clock can be queried and set with the timedatectl command. You can see the current hardware clock time standard of the Arch system using:

$ timedatectl | grep local
RTC in local TZ: no

To change the hardware clock time standard to localtime, use:

# timedatectl set-local-rtc 1

To revert to the hardware clock being in UTC, type:

# timedatectl set-local-rtc 0

These generates /etc/adjtime automatically and updates the RTC accordingly; no further configuration is required.

During kernel startup, at the point when the RTC driver is loaded, the system clock may be set from the hardware clock. Whether this occurs depends on the hardware platform, the version of the kernel and kernel build options. If this does occur, at this point in the boot sequence, the hardware clock time is assumed to be UTC and the value of /sys/class/rtc/rtcN/hctosys (N=0,1,2,..) will be set to 1.

Later, the system clock is set again from the hardware clock by systemd, dependent on values in /etc/adjtime. Hence, having the hardware clock using localtime may cause some unexpected behavior during the boot sequence; e.g system time going backwards, which is always a bad idea (there is a lot more to it). To avoid it systemd will only synchronize back, if the hardware clock is set to UTC and keep the kernel uninformed about the local timezone. As a consequence timestamps on a FAT filesystem touched by the Linux system will be in UTC.

Note:
  • The use of timedatectl requires an active dbus. Therefore, it may not be possible to use this command under a chroot (such as during installation). In these cases, you can revert back to the hwclock command.
  • If /etc/adjtime is not present, systemd assumes the hardware clock is set to UTC.

UTC in Windows

Warning: This method uses functionality that is buggy in old Windows versions (pre-7) and Microsoft recommends not to use it. See [1] for details. Another bug exists on Windows before Vista SP2 that resets the clock to localtime after resuming from the suspend/hibernation state. For even older versions of Windows, you might want to read http://www.cl.cam.ac.uk/~mgk25/mswish/ut-rtc.html - the functionality was not even documented nor officially supported then. For these operating systems, it is recommended to use localtime. If you are using newer versions of Windows, you may safely disregard this warning.

One reason users often set the RTC in localtime is to dual boot with Windows (which uses localtime). However, Windows is able to deal with the RTC being in UTC with a simple registry fix. It is recommended to configure Windows to use UTC, rather than Linux to use localtime.

Using regedit, add a DWORD value with hexadecimal value 1 to the registry:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\TimeZoneInformation\RealTimeIsUniversal

You can do this from an Administrator Command Prompt running:

reg add "HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\TimeZoneInformation" /v RealTimeIsUniversal /d 1 /t REG_DWORD /f

Alternatively, create a *.reg file (on the desktop) with the following content and double-click it to import it into registry:

Windows Registry Editor Version 5.00

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\TimeZoneInformation]
     "RealTimeIsUniversal"=dword:00000001
Note: If the above appears to have no effect, and a 64-bit variant of Windows is being used, using a QWORD value instead of a DWORD value may resolve the issue.

Should Windows ask to update the clock due to DST changes, let it. It will leave the clock in UTC as expected, only correcting the displayed time.

The #Hardware clock and #System clock time may need to be updated after setting this value.

If you are having issues with the offset of the time, try reinstalling tzdata and then setting your time zone again:

# timedatectl set-timezone America/Los_Angeles

UTC in Ubuntu

Ubuntu and its derivatives have the hardware clock set to be interpreted as in "localtime" if Windows was detected on any disk during Ubuntu installation. This is apparently done deliberately to allow new Linux users to try out Ubuntu on their Windows computers without editing the registry.

For changing this behavior, see above.

Time zone

To check the current zone defined for the system:

$ timedatectl status

To list available zones:

$ timedatectl list-timezones

To set your time zone:

# timedatectl set-timezone Zone/SubZone

Example:

# timedatectl set-timezone Canada/Eastern

This will create an /etc/localtime symlink that points to a zoneinfo file under /usr/share/zoneinfo/. In case you choose to create the link manually (for example during chroot where timedatectl won't work), keep in mind that it must be a symbolic link, as specified in archlinux(7):

# ln -sf /usr/share/zoneinfo/Zone/SubZone /etc/localtime
Tip: The time zone can also be selected interactively with tzselect.

See timedatectl(1), localtime(5) and archlinux(7) for details.

Setting based on geolocation

To set the timezone automatically based on the IP address location, one can use a geolocation API to retrieve the timezone, for example $ curl https://ipapi.co/timezone, and pass the output to timedatectl set-timezone for automatic setting. Some geo-IP APIs that provide free or partly free services are listed below:

Alternatively, the tool tzupdateAUR automatically sets the timezone based on the geolocation of the IP address.

Time skew

Every clock has a value that differs from real time (the best representation of which being International Atomic Time); no clock is perfect. A quartz-based electronic clock keeps imperfect time, but maintains a consistent inaccuracy. This base 'inaccuracy' is known as 'time skew' or 'time drift'.

When the hardware clock is set with hwclock, a new drift value is calculated in seconds per day. The drift value is calculated by using the difference between the new value set and the hardware clock value just before the set, taking into account the value of the previous drift value and the last time the hardware clock was set. The new drift value and the time when the clock was set is written to the file /etc/adjtime overwriting the previous values. The hardware clock can therefore be adjusted for drift when the command hwclock --adjust is run; this also occurs on shutdown but only if the hwclock daemon is enabled, hence for Arch systems which use systemd, this does not happen.

Note: If the hwclock has been set again less than 24 hours after a previous set, the drift is not recalculated as hwclock considers the elapsed time period too short to accurately calculate the drift.

If the hardware clock keeps losing or gaining time in large increments, it is possible that an invalid drift has been recorded (but only applicable, if the hwclock daemon is running). This can happen if you have set the hardware clock time incorrectly or your time standard is not synchronized with a Windows or macOS install. The drift value can be removed by removing the file /etc/adjtime, then set the correct hardware clock and system clock time, and check if your time standard is correct.

Note: If wish to make use of the drift value stored in /etc/adjtime even when using systemd, (i.e. perhaps you cannot or do not want to use NTP), you need to call hwclock --adjust on a regular basis, perhaps by creating a cron job.

The software clock is very accurate but like most clocks is not perfectly accurate and will drift as well. Though rarely, the system clock can lose accuracy if the kernel skips interrupts. There are some tools to improve software clock accuracy:

Time synchronization

See Category:Network Time Protocol.

Per-user/session or temporary settings

For some use cases it may be useful to change the time settings without touching the global system values. For example to test applications relying on the time during development or adjusting the system time zone when logging into a server remotely from another zone.

To make an application "see" a different date/time than the system one, you can use the faketime (from libfaketime) or the datefudge utilities.

If instead you want an application to "see" a different time zone than the system one, set the TZ environment variable, for example:

$ date && export TZ="/usr/share/zoneinfo/Pacific/Fiji" && date
Tue Nov  1 14:34:51 CET 2016
Wed Nov  2 01:34:51 FJT 2016

This is different than just setting the time, as for example it allows to test the behaviour of a program with positive or negative UTC offset values, or the effects of DST changes when developing on systems in a non-DST time zone.

Another use case is having different time zones set for different users of the same system: this can be accomplished by setting the TZ variable in the shell's configuration file, see Environment variables#Defining variables and Autostarting#Shells[broken link: invalid section].

Troubleshooting

Clock shows a value that is neither UTC nor local time

This might be caused by a number of reasons. For example, if your hardware clock is running on local time, but timedatectl is set to assume it is in UTC, the result would be that your timezone's offset to UTC effectively gets applied twice, resulting in wrong values for your local time and UTC.

To force your clock to the correct time, and to also write the correct UTC to your hardware clock, follow these steps:

  • Setup ntpd (enabling it as a service is not necessary).
  • Set your time zone correctly.
  • Run ntpd -qg to manually synchronize your clock with the network, ignoring large deviations between local UTC and network UTC.
  • Run hwclock --systohc to write the current software UTC time to the hardware clock.

Tips and tricks

fake-hwclock

alarm-fake-hwclock designed especially for system without battery backed up RTC, it includes a systemd service which on shutdown saves the current time and on startup restores the saved time, thus avoiding strange time travel errors.

Install fake-hwclock-gitAUR, start and enable the service fake-hwclock.service.

See also