From ArchWiki
Jump to: navigation, search

PHC is an acpi-cpufreq patch built with the purpose of enabling undervolting on your processor. This can potentially divide the power consumption of your processor by two or more, and in turn increase battery life and reduce fan noise noticiably. PHC works only if your processor's architecture supports undervolting.

Supported CPUs

PHC supports the following processor families:


Note: Current Intel core i CPUs use Intel P-states instead of acpi_cpufreq and are therefor not compatible with PHC.
  • Mobile Centrino
  • Atom (N2xx)
  • Core / Core2 (T and P Series)
  • Core i (2nd generation and older, tested on Core i3 550)
Note: Frequency locking does not seem to be working on Core i3 with the current stable 0.3.2 release of PHC, so finding the best vids for all but the highest frequency might be difficult or impossible.


  • K8 series


Install the phc-intelAUR package if you have an Intel processor, or phc-k8AUR if you have an AMD-K8-series one.

Next you need to compile the module for your kernel; this will also be necessary after a kernel update (but see the section below on using DKMS to automate this).

You need to have linux-headers and/or linux-lts-headers installed to be able to build the module.


# phc-intel setup


# phc-k8 setup

depending on processor.

If the acpi-cpufreq module is not already being loaded at boot, create the appropriate file in /etc/modules-load.d/. See Kernel modules for more information.

Note: In the case of phc-intelAUR, the acpi-cpufreq module is automatically loaded by /usr/lib/modprobe.d/phc-intel.conf.

Automatic module generation with DKMS

The dkms-phc-intelAUR package uses DKMS to automatically update the module after a kernel update. This is done at shutdown time to ensure that the kernel and kernel-headers are in sync (which is not necessarily the case during a system upgrade, depending on the order at which updates are installed).

To enable the systemd service, type:

# systemctl enable dkms-phc-intel


Finding safe low voltages

To automatically find the best voltages, you can use the mprime-phc-setup script (source-code). Just copy the code into a text file, chmod +x it to make it executable and run it. You need to install mprimeAUR or mprime-binAUR first (it is used to check that the CPU is stable). This script has not been tested on many systems yet, but should be safe.

Editing the configuration

After the phc module is compiled and the lowest voltages are found, they need to be added to the configuration file at /etc/default/phc-intel or /etc/default/phc-k8.

For example:

VIDS="25 22 15 8 5"

Simply restart the system and the modules will be loaded automatically by systemd.


Module loading


$ dmesg | grep acpi-cpufreq

If you see errors regarding this module, something has gone wrong OR you cannot use PHC.

Hardware recognition

There should be some files in /sys/devices/system/cpu/cpu0/cpufreq/ beginning with "phc_". To check whether PHC is working or not, just type:

$ cat /sys/devices/system/cpu/cpu0/cpufreq/phc_controls

you should read some values. If the values do not appear, then PHC is probably not supported by your CPU.

Voltage controlling

You can easily check whether PHC is working or not by looking at the cpu voltages: if the voltages are lower than the normal ones, then PHC has done its job. You can also manually set voltages, for example:

# echo 34 26 18 12 8 5 > /sys/devices/system/cpu/cpu0/cpufreq/phc_vids

System stability

To make sure that your undervolted CPU is stable, you can run long sessions of mprimeAUR and/or linpackAUR (Intel-only).