Wireless network configuration

From ArchWiki
(Redirected from Rfkill)
Jump to: navigation, search

Configuring wireless is a two-part process; the first part is to identify and ensure the correct driver for your wireless device is installed (they are available on the installation media, but often have to be installed explicitly), and to configure the interface. The second is choosing a method of managing wireless connections. This article covers both parts, and provides additional links to wireless management tools.


Device driver

The default Arch Linux kernel is modular, meaning many of the drivers for machine hardware reside on the hard drive and are available as modules. At boot, udev takes an inventory of your hardware and loads appropriate modules (drivers) for your corresponding hardware, which will in turn allow creation of a network interface.

Some wireless chipsets also require firmware, in addition to a corresponding driver. Many firmware images are provided by the linux-firmware package which is installed by default, however, proprietary firmware images are not included and have to be installed separately. This is described in #Installing driver/firmware.

Note: Udev is not perfect. If the proper module is not loaded by udev on boot, simply load it manually. Note also that udev may occasionally load more than one driver for a device, and the resulting conflict will prevent successful configuration. Make sure to blacklist the unwanted module.
Tip: Though not strictly required, it's a good idea to first install user-space tools mentioned in #Manual setup, especially when some problem should appear.

Check the driver status

To check if the driver for your card has been loaded, check the output of the lspci -k or lsusb -v command, depending on if the card is connected by PCI(e) or USB. You should see that some kernel driver is in use, for example:

$ lspci -k
06:00.0 Network controller: Intel Corporation WiFi Link 5100
	Subsystem: Intel Corporation WiFi Link 5100 AGN
	Kernel driver in use: iwlwifi
	Kernel modules: iwlwifi
Note: If the card is a USB device, running dmesg | grep usbcore should give something like usbcore: registered new interface driver rtl8187 as output.

Also check the output of ip link command to see if a wireless interface (usually it starts with the letter "w", e.g. wlp2s1) was created. Then bring the interface up with ip link set interface up. For example, assuming the interface is wlan0:

# ip link set wlan0 up

If you get this error message: SIOCSIFFLAGS: No such file or directory, it most certainly means that your wireless chipset requires a firmware to function.

Check kernel messages for firmware being loaded:

$ dmesg | grep firmware
[   7.148259] iwlwifi 0000:02:00.0: loaded firmware version build 35138 op_mode iwldvm

If there is no relevant output, check the messages for the full output for the module you identified earlier (iwlwifi in this example) to identify the relevant message or further issues:

$ dmesg | grep iwlwifi
[   12.342694] iwlwifi 0000:02:00.0: irq 44 for MSI/MSI-X
[   12.353466] iwlwifi 0000:02:00.0: loaded firmware version build 35138 op_mode iwldvm
[   12.430317] iwlwifi 0000:02:00.0: CONFIG_IWLWIFI_DEBUG disabled
[   12.430341] iwlwifi 0000:02:00.0: Detected Intel(R) Corporation WiFi Link 5100 AGN, REV=0x6B

If the kernel module is successfully loaded and the interface is up, you can skip the next section.

Installing driver/firmware

Check the following lists to discover if your card is supported:

Note that some vendors ship products that may contain different chip sets, even if the product identifier is the same. Only the usb-id (for USB devices) or pci-id (for PCI devices) is authoritative.

If your wireless card is listed above, follow the #Troubleshooting drivers and firmware subsection of this page, which contains information about installing drivers and firmware of some specific wireless cards. Then check the driver status again.

If your wireless card is not listed above, it is likely supported only under Windows (some Broadcom, 3com, etc). For these, you can try to use #ndiswrapper.

Wireless management

The #Manual setup uses command-line tools to manually manage your network interface. The #Automatic setup section describes several programs that can be used to automatically manage your wireless interface, some of which include a GUI and all of which include support for network profiles (useful when frequently switching wireless networks, like with laptops).

Manual setup

Just like other network interfaces, the wireless ones are controlled with ip from the iproute2 package.

You will need to install a basic set of tools for managing the wireless connection. Install one of the following:

  • iwiw only supports the nl80211 (netlink) standard. It does not support the older WEXT (Wireless EXTentions) standard. If iw does not see your card, this may be the reason.
https://wireless.kernel.org/en/users/Documentation/iw || iw
  • wireless_toolswireless_tools is deprecated but still widely supported. Use this for modules using the WEXT standard.
http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html || wireless_tools
Tip: For a comparison of commands between iw and wireless_tools, see #iw and wireless_tools comparison.

For WPA/WPA2 encryption, you will also need:

  • WPA supplicant — wpa_supplicant is a cross-platform supplicant with support for WEP, WPA and WPA2 (IEEE 802.11i / RSN (Robust Secure Network)). It is suitable for desktops, laptops and embedded systems and works with both WEXT and nl80211.
http://hostap.epitest.fi/wpa_supplicant/ || wpa_supplicant
  • Note that most of the commands have to be executed with root permissions. Executed with normal user rights, some of the commands (e.g. iwlist), will exit without error but not produce the correct output either, which can be confusing.
  • Depending on your hardware and encryption type, some of these steps may not be necessary. Some cards are known to require interface activation and/or access point scanning before being associated to an access point and being given an IP address. Some experimentation may be required. For instance, WPA/WPA2 users may try to directly activate their wireless network from step #Association[broken link: invalid section].

Examples in this section assume that your wireless device interface is interface and that you are connecting to your_essid wifi access point. Replace both accordingly. To find your wireless device interface, see #Getting some useful information[broken link: invalid section].

Get the name of the interface

Tip: See official documentation of the iw tool for more examples.

To get the name of your wireless interface do:

$ iw dev

The name of the interface will be output after the word "Interface". For example, it is commonly wlan0.

Get the status of the interface

To check link status, use following command.

$ iw dev interface link

You can get statistic information, such as the amount of tx/rx bytes, signal strength etc., with following command:

$ iw dev interface station dump

Activate the interface

Tip: Usually this step is not required.

Some cards require that the kernel interface be activated before you can use iw or wireless_tools:

# ip link set interface up
Note: If you get errors like RTNETLINK answers: Operation not possible due to RF-kill, make sure that hardware switch is on. See #Rfkill caveat for details.

To verify that the interface is up, inspect the output of the following command:

# ip link show interface
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state DOWN mode DORMANT group default qlen 1000
    link/ether 12:34:56:78:9a:bc brd ff:ff:ff:ff:ff:ff

The UP in <BROADCAST,MULTICAST,UP,LOWER_UP> is what indicates the interface is up, not the later state DOWN.

Discover access points

To see what access points are available:

# iw dev interface scan | less
Note: If it displays Interface does not support scanning, then you probably forgot to install the firmware. In some cases this message is also displayed when not running iw as root.
Tip: Depending on your location, you might need to set the correct regulatory domain in order to see all available networks.

The important points to check:

  • SSID: the name of the network.
  • Signal: is reported in a wireless power ratio in dBm (e.g. from -100 to 0). The closer the negative value gets to zero, the better the signal. Observing the reported power on a good quality link and a bad one should give an idea about the individual range.
  • Security: it is not reported directly, check the line starting with capability. If there is Privacy, for example capability: ESS Privacy ShortSlotTime (0x0411), then the network is protected somehow.
    • If you see an RSN information block, then the network is protected by Robust Security Network protocol, also known as WPA2.
    • If you see an WPA information block, then the network is protected by Wi-Fi Protected Access protocol.
    • In the RSN and WPA blocks you may find the following information:
      • Group cipher: value in TKIP, CCMP, both, others.
      • Pairwise ciphers: value in TKIP, CCMP, both, others. Not necessarily the same value than Group cipher.
      • Authentication suites: value in PSK, 802.1x, others. For home router, you will usually find PSK (i.e. passphrase). In universities, you are more likely to find 802.1x suite which requires login and password. Then you will need to know which key management is in use (e.g. EAP), and what encapsulation it uses (e.g. PEAP). See WPA2 Enterprise and Wikipedia:Authentication protocol for details.
    • If you see neither RSN nor WPA blocks but there is Privacy, then WEP is used.

Set operating mode

You might need to set the proper operating mode of the wireless card. More specifically, if you are going to connect an ad-hoc network, you need to set the operating mode to ibss:

# iw dev interface set type ibss
Note: Changing the operating mode on some cards might require the wireless interface to be down (ip link set interface down).

Connect to an access point

Depending on the encryption, you need to associate your wireless device with the access point to use and pass the encryption key:

  • No encryption
    # iw dev interface connect "your_essid"
  • WEP
    • using a hexadecimal or ASCII key (the format is distinguished automatically, because a WEP key has a fixed length):
      # iw dev interface connect "your_essid" key 0:your_key
    • using a hexadecimal or ASCII key, specifying the third set up key as default (keys are counted from zero, four are possible):
      # iw dev interface connect "your_essid" key d:2:your_key
  • WPA/WPA2 According to what you got from #Discover access points, issue this command:
    # wpa_supplicant -i interface -c <(wpa_passphrase "your_SSID" "your_key")

If this does not work, you may need to adjust the options. If connected successfully, continue in a new terminal (or quit wpa_supplicant with Ctrl+c and add the -B switch to the above command to run it in the background). WPA supplicant contains more information on options and on how to create a permanent configuration file for the wireless access point.

Regardless of the method used, you can check if you have associated successfully:

# iw dev interface link

Get an IP address

Follow the instructions in Network configuration#Configure the IP address[broken link: invalid section].


Here is a complete example of setting up a wireless network with WPA supplicant and DHCP.

# ip link set dev wlan0 up
# wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf
# dhcpcd wlan0

And then to close the connection, you can simply disable the interface:

# ip link set dev wlan0 down

For a static IP, you would replace the dhcpcd command with

# ip addr add broadcast dev wlan0
# ip route add default via

And before disabling the interface you would first flush the IP address and gateway:

# ip addr flush dev wlan0
# ip route flush dev wlan0

Automatic setup

There are many solutions to choose from, but remember that all of them are mutually exclusive; you should not run two daemons simultaneously. The following table compares the different connection managers, additional notes are in subsections below.

Connection manager Network
(auto connect dropped
or changed location)
PPP support
(e.g. 3G modem)
Archiso [1] Official
Console tools Systemd units
Connman Yes Yes Yes No No connmanctl connman.service
netctl Yes Yes Yes Yes (base) No netctl,wifi-menu netctl-auto@interface.service
NetworkManager Yes Yes Yes No Yes nmcli,nmtui NetworkManager.service
Wicd Yes Yes No No Yes wicd-curses wicd.service
Wifi Radar Yes Yes No No Yes wifi-radar

See also List of applications/Internet#Network managers.

WPA2 Enterprise

WPA2 Enterprise is a mode of Wi-Fi Protected Access. It provides better security and key management than WPA2 Personal, and supports other enterprise-type functionality, such as VLANs and NAP. However, it requires an external authentication server, called RADIUS server to handle the authentication of users. This is in contrast to Personal mode which does not require anything beyond the wireless router or access points (APs), and uses a single passphrase or password for all users.

The Enterprise mode enables users to log onto the Wi-Fi network with a username and password and/or a digital certificate. Since each user has a dynamic and unique encryption key, it also helps to prevent user-to-user snooping on the wireless network, and improves encryption strength.

This section describes the configuration of network clients to connect to a wireless access point with WPA2 Enterprise mode. See Software access point#RADIUS for information on setting up an access point itself.

Note: Enterprise mode requires a more complex client configuration, whereas Personal mode only requires entering a passphrase when prompted. Clients likely need to install the server’s CA certificate (plus per-user certificates if using EAP-TLS), and then manually configure the wireless security and 802.1X authentication settings.

For a comparison of protocols see the following table.

Warning: It is possible to use WPA2 Enterprise without the client checking the server CA certificate. However, you should always seek to do so, because without authenticating the access point the connection can be subject to a man-in-the-middle attack. This may happen because while the connection handshake itself may be encrypted, the most widely used setups transmit the password itself either in plain text or the easily breakable #MS-CHAPv2. Hence, the client might send the password to a malicious access point which then proxies the connection.


eduroam is an international roaming service for users in research, higher education and further education, based on WPA2 Enterprise.

  • Check connection details first with your institution before applying any profiles listed in this section. Example profiles are not guaranteed to work or match any security requirements.
  • When storing connection profiles unencrypted, it is recommended restrict read access to the root account by specifying chmod 600 profile as root.
Tip: Configuration for NetworkManager and #wpa_supplicant can be generated with the eduroam Configuration Assistant Tool.

Manual/automatic setup


WPA supplicant can be configured directly and used in combination with a dhcp client or with systemd. See the examples in /etc/wpa_supplicant/wpa_supplicant.conf for configuring the connection details.


NetworkManager can generate WPA2 Enterprise profiles with graphical front ends. nmcli and nmtui do not support this, but may use existing profiles.


connman needs a separate configuration file before connecting to the network. See connman-service.config(5) and Connman#Connecting to eduroam[broken link: invalid section] for details.


netctl supports #wpa_supplicant configuration through blocks included with WPAConfigSection=. See netctl.profile(5) for details.

Warning: Special quoting rules apply: see the SPECIAL QUOTING RULES section in netctl.profile(5).
Tip: Custom certificates can be specified by adding the line 'ca_cert="/path/to/special/certificate.cer"' in WPAConfigSection.



WPA2-Enterprise wireless networks demanding MSCHAPv2 type-2 authentication with PEAP sometimes require pptpclient in addition to the stock ppp package. netctl seems to work out of the box without ppp-mppe, however. In either case, usage of MSCHAPv2 is discouraged as it is highly vulnerable, although using another method is usually not an option. See also [2] and [3].

Tips and tricks

Respecting the regulatory domain

The regulatory domain, or "regdomain", is used to reconfigure wireless drivers to make sure that wireless hardware usage complies with local laws set by the FCC, ETSI and other organizations. Regdomains use ISO 3166-1 alpha-2 country codes. For example, the regdomain of the United States would be "US", China would be "CN", etc.

Regdomains affect the availability of wireless channels. In the 2.4GHz band, the allowed channels are 1-11 for the US, 1-14 for Japan, and 1-13 for most of the rest of the world. In the 5GHz band, the rules for allowed channels are much more complex. In either case, consult this list of WLAN channels for more detailed information.

Regdomains also affect the limit on the effective isotropic radiated power (EIRP) from wireless devices. This is derived from transmit power/"tx power", and is measured in dBm/mBm (1dBm=100mBm) or mW (log scale). In the 2.4GHz band, the maximum is 30dBm in the US and Canada, 20dBm in most of Europe, and 20dB-30dBm for the rest of the world. In the 5GHz band, maximums are usually lower. Consult the wireless-regdb for more detailed information (EIRP dBm values are in the second set of brackets for each line).

Misconfiguring the regdomain can be useful - for example, by allowing use of an unused channel when other channels are crowded, or by allowing an increase in tx power to widen transmitter range. However, this is not recommended as it could break local laws and cause interference with other radio devices.

To configure the regdomain, install crda and reboot (to reload the cfg80211 module and all related drivers). Check the boot log to make sure that CRDA is being called by cfg80211:

$ dmesg | grep cfg80211

The current regdomain can be set to the United States with:

# iw reg set US

And queried with:

$ iw reg get
Note: Your device may be set to country "00", which is the "world regulatory domain" and contains generic settings. If this cannot be unset, CRDA may be misconfigured.

However, setting the regdomain may not alter your settings. Some devices have a regdomain set in firmware/EEPROM, which dictates the limits of the device, meaning that setting regdomain in software can only increase restrictions, not decrease them. For example, a CN device could be set in software to the US regdomain, but because CN has an EIRP maximum of 20dBm, the device will not be able to transmit at the US maximum of 30dBm.

For example, to see if the regdomain is being set in firmware for an Atheros device:

$ dmesg | grep ath:

For other chipsets, it may help to search for "EEPROM", "regdomain", or simply the name of the device driver.

To see if your regdomain change has been successful, and to query the number of available channels and their allowed transmit power:

$ iw list | grep -A 15 Frequencies:

A more permanent configuration of the regdomain can be achieved through editing /etc/conf.d/wireless-regdom and uncommenting the appropriate domain. wpa_supplicant can also use a regdomain in the country= line of /etc/wpa_supplicant/wpa_supplicant.conf.

It is also possible to configure the cfg80211 kernel module to use a specific regdomain by adding, for example, options cfg80211 ieee80211_regdom=EU as module options. However, this is part of the old regulatory implementation.

For further information, read the wireless.kernel.org regulatory documentation.

iw and wireless_tools comparison

The table below gives an overview of comparable commands for iw and wireless_tools. See iw replaces iwconfig for more examples.

iw command wireless_tools command Description
iw dev wlan0 link iwconfig wlan0 Getting link status.
iw dev wlan0 scan iwlist wlan0 scan Scanning for available access points.
iw dev wlan0 set type ibss iwconfig wlan0 mode ad-hoc Setting the operation mode to ad-hoc.
iw dev wlan0 connect your_essid iwconfig wlan0 essid your_essid Connecting to open network.
iw dev wlan0 connect your_essid 2432 iwconfig wlan0 essid your_essid freq 2432M Connecting to open network specifying channel.
iw dev wlan0 connect your_essid key 0:your_key iwconfig wlan0 essid your_essid key your_key Connecting to WEP encrypted network using hexadecimal key.
iwconfig wlan0 essid your_essid key s:your_key Connecting to WEP encrypted network using ASCII key.
iw dev wlan0 set power_save on iwconfig wlan0 power on Enabling power save.


This section contains general troubleshooting tips, not strictly related to problems with drivers or firmware. For such topics, see next section #Troubleshooting drivers and firmware.

Temporary internet access

If you have problematic hardware and need internet access to, for example, download some software or get help in forums, you can make use of Android's built-in feature for internet sharing via USB cable. See Android tethering#USB tethering for more information.

Rfkill caveat

Many laptops have a hardware button (or switch) to turn off wireless card, however, the card can also be blocked by kernel. This can be handled by rfkill. Use rfkill to show the current status:

# rfkill list
0: phy0: Wireless LAN
	Soft blocked: yes
	Hard blocked: yes

If the card is hard-blocked, use the hardware button (switch) to unblock it. If the card is not hard-blocked but soft-blocked, use the following command:

# rfkill unblock wifi
Note: It is possible that the card will go from hard-blocked and soft-unblocked state into hard-unblocked and soft-blocked state by pressing the hardware button (i.e. the soft-blocked bit is just switched no matter what). This can be adjusted by tuning some options of the rfkill kernel module.

Hardware buttons to toggle wireless cards are handled by a vendor specific kernel module, frequently these are WMI modules. Particularly for very new hardware models, it happens that the model is not fully supported in the latest stable kernel yet. In this case it often helps to search the kernel bug tracker for information and report the model to the maintainer of the respective vendor kernel module, if it has not happened already.

See also: http://askubuntu.com/questions/62166/siocsifflags-operation-not-possible-due-to-rf-kill

Observing Logs

A good first measure to troubleshoot is to analyze the system's logfiles first. In order not to manually parse through them all, it can help to open a second terminal/console window and watch the kernels messages with

$ dmesg -w

while performing the action, e.g. the wireless association attempt.

When using a tool for network management, the same can be done for systemd with

# journalctl -f 

Frequently a wireless error is accompanied by a deauthentication with a particular reason code, for example:

wlan0: deauthenticating from XX:XX:XX:XX:XX:XX by local choice (reason=3)

Looking up the reason code might give a first hint. Maybe it also helps you to look at the control message flowchart, the journal messages will follow it.

The individual tools used in this article further provide options for more detailed debugging output, which can be used in a second step of the analysis, if required.

Power saving

See Power saving#Network interfaces.

Failed to get IP address

  • If getting an IP address repeatedly fails using the default dhcpcd client, try installing and using dhclient instead. Do not forget to select dhclient as the primary DHCP client in your connection manager!
  • If you can get an IP address for a wired interface and not for a wireless interface, try disabling the wireless card's power saving features (specify off instead of on).
  • If you get a timeout error due to a waiting for carrier problem, then you might have to set the channel mode to auto for the specific device:
# iwconfig wlan0 channel auto

Before changing the channel to auto, make sure your wireless interface is down. After it has successfully changed it, you can bring the interface up again and continue from there.

Valid IP address but cannot resolve host

If you are on a public wireless network that may have a captive portal, make sure to query an HTTP page (not an HTTPS page) from your web browser, as some captive portals only redirect HTTP. If this is not the issue, it may be necessary to remove any custom DNS servers from resolv.conf.

Setting RTS and fragmentation thresholds

Wireless hardware disables RTS and fragmentation by default. These are two different methods of increasing throughput at the expense of bandwidth (i.e. reliability at the expense of speed). These are useful in environments with wireless noise or many adjacent access points, which may create interference leading to timeouts or failing connections.

Packet fragmentation improves throughput by splitting up packets with size exceeding the fragmentation threshold. The maximum value (2346) effectively disables fragmentation since no packet can exceed it. The minimum value (256) maximizes throughput, but may carry a significant bandwidth cost.

# iw phy0 set frag 512

RTS improves throughput by performing a handshake with the access point before transmitting packets with size exceeding the RTS threshold. The maximum threshold (2347) effectively disables RTS since no packet can exceed it. The minimum threshold (0) enables RTS for all packets, which is probably excessive for most situations.

# iw phy0 set rts 500
Note: phy0 is the name of the wireless device as listed by $ iw phy.

Random disconnections

Cause #1

If dmesg says wlan0: deauthenticating from MAC by local choice (reason=3) and you lose your Wi-Fi connection, it is likely that you have a bit too aggressive power-saving on your Wi-Fi card[4]. Try disabling the wireless card's power saving features (specify off instead of on).

If your card does not support enabling/disabling power save mode, check the BIOS for power management options. Disabling PCI-Express power management in the BIOS of a Lenovo W520 resolved this issue.

Cause #2

If you are experiencing frequent disconnections and dmesg shows messages such as

ieee80211 phy0: wlan0: No probe response from AP xx:xx:xx:xx:xx:xx after 500ms, disconnecting

try changing the channel bandwidth to 20MHz through your router's settings page.

Cause #3

On some laptop models with hardware rfkill switches (e.g., Thinkpad X200 series), due to wear or bad design, the switch (or its connection to the mainboard) might become loose over time resulting in seemingly random hardblocks/disconnects when you accidentally touch the switch or move the laptop. There is no software solution to this, unless your switch is electrical and the BIOS offers the option to disable the switch. If your switch is mechanical (most are), there are lots of possible solutions, most of which aim to disable the switch: Soldering the contact point on the mainboard/wifi-card, glueing or blocking the switch, using a screw nut to tighten the switch or removing it altogether.

Cause #4

Another cause for frequent disconnects or a complete failure to connect may also be a sub-standard router, incomplete settings of the router, or interference by other wireless devices.

To troubleshoot, first best try to connect to the router with no authentication.

If that works, enable WPA/WPA2 again but choose fixed and/or limited router settings. For example:

  • If the router is considerably older than the wireless device you use for the client, test if it works with setting the router to one wireless mode
  • Disable mixed-mode authentication (e.g. only WPA2 with AES, or TKIP if the router is old)
  • Try a fixed/free channel rather than "auto" channel (maybe the router next door is old and interfering)
  • Disable WPS
  • Disable 40Mhz channel bandwidth (lower throughput but less likely collisions)
  • If the router has quality of service settings, check completeness of settings (e.g. Wi-Fi Multimedia (WMM) is part of optional QoS flow control. An erroneous router firmware may advertise its existence although the setting is not enabled)

Troubleshooting drivers and firmware

This section covers methods and procedures for installing kernel modules and firmware for specific chipsets, that differ from generic method.

See Kernel modules for general informations on operations with modules.



Unified driver for Ralink chipsets (it replaces rt2500, rt61, rt73, etc). This driver has been in the Linux kernel since 2.6.24, you only need to load the right module for the chip: rt2400pci, rt2500pci, rt2500usb, rt61pci or rt73usb which will autoload the respective rt2x00 modules too.

A list of devices supported by the modules is available at the project's homepage[dead link 2016-08-02].

Additional notes
  • Since kernel 3.0, rt2x00 includes also these drivers: rt2800pci, rt2800usb.
  • Since kernel 3.0, the staging drivers rt2860sta and rt2870sta are replaced by the mainline drivers rt2800pci and rt2800usb[5].
  • Some devices have a wide range of options that can be configured with iwpriv. These are documented in the source tarballs available from Ralink.


For devices which are using the rt3090 chipset it should be possible to use rt2800pci driver, however, is not working with this chipset very well (e.g. sometimes it is not possible to use higher rate than 2Mb/s).


The rt3290 chipset is recognised by the kernel rt2800pci module. However, some users experience problems and reverting to a patched Ralink driver seems to be beneficial in these cases.


New chipset as of 2012. It may require proprietary drivers from Ralink. Different manufacturers use it, see the Belkin N750 DB wireless usb adapter forums thread.


New chipset as of 2012 with support for 5 Ghz bands. It may require proprietary drivers from Ralink and some effort to compile them. At the time of writing a how-to on compilation is available for a DLINK DWA-160 rev. B2 here.



The driver is now in the kernel, but many users have reported being unable to make a connection although scanning for networks does work.

8192cu-dkmsAUR includes many patches, try this if it does not work fine with the driver in kernel.


The driver is part of the current kernel package. The module initialization may fail at boot giving this error message:

rtl819xE:ERR in CPUcheck_firmware_ready()
rtl819xE:ERR in init_firmware() step 2
rtl819xE:ERR!!! _rtl8192_up(): initialization is failed!
r8169 0000:03:00.0: eth0: link down

A workaround is to simply unload the module:

# modprobe -r r8192e_pci

and reload the module (after a pause):

# modprobe r8192e_pci


Some dongles, like the TP-Link TL-WN725N v2 (not sure, but it seems that uses the rtl8179 chipset), use chipsets compatible with this driver. In Linux 3.12 the driver has been moved to kernel staging source tree. For older kernels use out-of-tree driver sources built with DKMS - install 8188eu-dkmsAUR. At the times of 3.15 kernel rtl8188eu driver is buggy and has many stability issues.


The rtl8723ae and rtl8723be modules are included in the mainline Linux kernel.

Some users may encounter errors with powersave on this card. This is shown with occasional disconnects that are not recognized by high level network managers (netctl, NetworkManager). This error can be confirmed by running dmesg -w or journalctl -f and looking for output related to powersave and the rtl8723ae/rtl8723be module. If you are having this issue, use the fwlps=0 kernel option, which should prevent the WiFi card from automatically sleeping and halting connection.

options rtl8723ae fwlps=0


options rtl8723be fwlps=0

If you have very poor signal maybe your device has only one antenna connected and auto mode does not work. You can force the antenna with ant_sel=1 or ant_sel=2 kernel option.


Newer 802.11 a/b/g/n usb adapters, such as the Glam Hobby AC600 (Ourlink) may require rtl8812 or rtl8821 drivers before working.

The 8812 driver can be found as rtl8812au-dkms-gitAUR.

# modprobe 8812au

If that does not work (like for the AC600 dongles), try the 8812/8821 module rtl8812au_rtl8821au-dkms-gitAUR.

# modprobe rtl8812au_rtl8821au

These require DKMS so make sure you have your proper kernel headers installed.


The MadWifi team currently maintains three different drivers for devices with Atheros chipset:

  • madwifi is an old, obsolete driver. Not present in Arch kernel since[6].
  • ath5k is newer driver, which replaces the madwifi driver. Currently a better choice for some chipsets, but not all chipsets are supported (see below)
  • ath9k is the newest of these three drivers, it is intended for newer Atheros chipsets. All of the chips with 802.11n capabilities are supported.

There are some other drivers for some Atheros devices. See Linux Wireless documentation for details.


External resources:

If you find web pages randomly loading very slow, or if the device is unable to lease an IP address, try to switch from hardware to software encryption by loading the ath5k module with nohwcrypt=1 option. See Kernel modules#Setting module options for details.

Some laptops may have problems with their wireless LED indicator flickering red and blue. To solve this problem, do:

# echo none > /sys/class/leds/ath5k-phy0::tx/trigger
# echo none > /sys/class/leds/ath5k-phy0::rx/trigger

For alternatives, see this bug report.


External resources:

As of Linux 3.15.1, some users have been experiencing a decrease in bandwidth. In some cases this can fixed by editing /etc/modprobe.d/ath9k.conf and adding the line:

options ath9k nohwcrypt=1
Note: Check with the command lsmod what module(-name) is in use and change it if named otherwise (e.g. ath9k_htc).

In the unlikely event that you have stability issues that trouble you, you could try using the backports-patchedAUR package. An ath9k mailing list exists for support and development related discussions.

Power saving

Although Linux Wireless says that dynamic power saving is enabled for Atheros ath9k single-chips newer than AR9280, for some devices (e.g. AR9285) powertop might still report that power saving is disabled. In this case enable it manually.

On some devices (e.g. AR9285), enabling the power saving might result in the following error:

# iw dev wlan0 set power_save on
command failed: Operation not supported (-95)

The solution is to set the ps_enable=1 option for the ath9k module:

options ath9k ps_enable=1


ipw2100 and ipw2200

These modules are fully supported in the kernel, but they require additional firmware. Depending on which of the chipsets you have, install either ipw2100-fw or ipw2200-fw. Then reload the appropriate module.

Tip: You may use the following module options:
  • use the rtap_iface=1 option to enable the radiotap interface
  • use the led=1 option to enable a front LED indicating when the wireless is connected or not


iwlegacy is the wireless driver for Intel's 3945 and 4965 wireless chips. The firmware is included in the linux-firmware package.

udev should load the driver automatically, otherwise load iwl3945 or iwl4965 manually. See Kernel modules for details.

If you have problems connecting to networks in general or your link quality is very poor, try to disable 802.11n:

options iwl4965 11n_disable=1


iwlwifi is the wireless driver for Intel's current wireless chips, such as 5100AGN, 5300AGN, and 5350AGN. See the full list of supported devices. The firmware is included in the linux-firmware package. The linux-firmware-iwlwifi-gitAUR may contain some updates sooner.

If you have problems connecting to networks in general or your link quality is very poor, try to disable 802.11n, and perhaps also enable software encryption:

options iwlwifi 11n_disable=1
options iwlwifi swcrypto=1

If you have a problem with slow uplink speed in 802.11n mode, for example 20Mbps, try to enable antenna aggregation:

options iwlwifi 11n_disable=8

Do not be confused with the option name, when the value is set to 8 it does not disable anything but re-enables transmission antenna aggregation.[7] [8]

In case this does not work for you, you may try disabling power saving for your wireless adapter.

Some have never gotten this to work. Others found salvation by disabling N in their router settings after trying everything. This is known to have be the only solution on more than one occasion. The second link there mentions a 5ghz option that might be worth exploring.

Bluetooth coexistence

If you have difficulty connecting a bluetooth headset and maintaining good downlink speed, try disabling bluetooth coexistence [9]:

options iwlwifi bt_coex_active=0

Disabling LED blink

Note: This works with the iwlegacy and iwlwifi drivers.

The default settings on the module are to have the LED blink on activity. Some people find this extremely annoying. To have the LED on solid when Wi-Fi is active, you can use the systemd-tmpfiles:

w /sys/class/leds/phy0-led/trigger - - - - phy0radio

Run systemd-tmpfiles --create phy0-led.conf for the change to take effect, or reboot.

To see all the possible trigger values for this LED:

# cat /sys/class/leds/phy0-led/trigger
Tip: If you do not have /sys/class/leds/phy0-led, you may try to use the led_mode="1" module option. It should be valid for both iwlwifi and iwlegacy drivers.


See Broadcom wireless.

Other drivers/devices

Tenda w322u

Treat this Tenda card as an rt2870sta device. See #rt2x00.


This should be a part of the kernel package and be installed already.

Some Orinoco chipsets are Hermes II. You can use the wlags49_h2_cs driver instead of orinoco_cs and gain WPA support. To use the driver, blacklist orinoco_cs first.


The driver p54 is included in kernel, but you have to download the appropriate firmware for your card from this site and install it into the /usr/lib/firmware directory.

Note: There is also older, deprecated driver prism54, which might conflict with the newer driver (p54pci or p54usb). Make sure to blacklist prism54.


Warning: The drivers for these devices are broken and do not work with newer kernel versions.

Packages: tiacx tiacx-firmware (deleted from official repositories and AUR)

See official wiki for details.


zd1211rw is a driver for the ZyDAS ZD1211 802.11b/g USB WLAN chipset, and it is included in recent versions of the Linux kernel. See [10] for a list of supported devices. You only need to install the firmware for the device, provided by the zd1211-firmware package.


Host AP is a Linux driver for wireless LAN cards based on Intersil's Prism2/2.5/3 chipset. The driver is included in Linux kernel.

Note: Make sure to blacklist the orinico_cs driver, it may cause problems.


Ndiswrapper is a wrapper script that allows you to use some Windows drivers in Linux. You will need the .inf and .sys files from your Windows driver.

Warning: Be sure to use drivers appropriate to your architecture (x86 vs. x86_64).
Tip: If you need to extract these files from an *.exe file, you can use cabextract.

Follow these steps to configure ndiswrapper.

1. Install ndiswrapper-dkms

2. Install the driver to /etc/ndiswrapper/*

# ndiswrapper -i filename.inf

3. List all installed drivers for ndiswrapper

$ ndiswrapper -l

4. Let ndiswrapper write its configuration in /etc/modprobe.d/ndiswrapper.conf:

# ndiswrapper -m
# depmod -a

Now the ndiswrapper install is almost finished; follow the instructions on Kernel modules#Automatic module handling to automatically load the module at boot.

The important part is making sure that ndiswrapper exists on this line, so just add it alongside the other modules. It would be best to test that ndiswrapper will load now, so:

# modprobe ndiswrapper
# iwconfig

and wlan0 should now exist. If you have problems, some help is available at: ndiswrapper howto and ndiswrapper FAQ.


backports-patchedAUR provide drivers released on newer kernels backported for usage on older kernels. The project started since 2007 and was originally known as compat-wireless, evolved to compat-drivers and was recently renamed simply to backports.

If you are using old kernel and have wireless issue, drivers in this package may help.

See also