Full system backup with rsync

From ArchWiki
(Redirected from Rsync/Full system backup)
Jump to: navigation, search

This article is about using rsync to transfer a copy of your "/" tree, excluding a few select folders. This approach is considered to be better than disk cloning with dd since it allows for a different size, partition table and filesystem to be used, and better than copying with cp -a as well, because it allows greater control over file permissions, attributes, Access Control Lists and extended attributes.

Either method will work even while the system is running, but files changed during the transfer may or may not be transferred, which could cause undefined behaviour of some programs using the transferred files.

This approach will also work well for migrating an existing installation to a new harddrive or SSD.

With a single command

This command depends on brace expansion available in both the bash and zsh shells. When using a different shell, --exclude patterns should be repeated manually.

# rsync -aAXv --exclude={"/dev/*","/proc/*","/sys/*","/tmp/*","/run/*","/mnt/*","/media/*","/lost+found"} / /path/to/backup/folder

Using the -aAX set of options, the files are transferred in archive mode, ensuring that symbolic links, devices, permissions and ownerships, modification times, ACLs and extended attributes are preserved (assuming that the target file system supports the feature).

The --exclude option will cause files that match the given patterns to be excluded. The contents of /dev, /proc, /sys, /tmp and /run were excluded because they are populated at boot (while the folders themselves are not created), /lost+found is filesystem-specific. Quoting the exclude patterns will avoid expansion by shell, which is necessary e.g. when backing up over SSH. Ending the excluded paths with * will still ensure that the directories themselves are created if not already existing.

  • If you plan on backing up your system somewhere other than /mnt or /media, do not forget to add it to the list of exclude patterns to avoid an infinite loop.
  • If there are any bind mounts in the system, they should be excluded as well, so that the bind mounted contents is copied only once.
  • If you use a swap file, make sure to exclude it as well.
  • Consider also if you want to backup the /home/ folder. If it contains your data, it might be considerably larger than the system. Otherwise consider excluding unimportant subdirectories such as /home/*/.thumbnails/*, /home/*/.cache/mozilla/*, /home/*/.cache/chromium/*, /home/*/.local/share/Trash/*, depending on software installed on the system. If GVFS is installed, /home/*/.gvfs must be excluded to prevent rsync errors.

You may want to include additional rsync options, such as the following (see man rsync for the full list):

  • If you are a heavy user of hardlinks, you might consider adding the -H option, which is turned off by default as memory expensive, but nowadays it should be no problem on most modern machines. There are a lot of hard links below the /usr/ folder, which save disk space.
  • You may want to add rsync's --delete option if you are running this multiple times to the same backup folder. In this case make sure that the source path does not end with /*, or this option will only have effect on the files inside the subdirectories of the source directory, but no effect on the files residing directly inside the source directory.
  • If you use any sparse files, such as virtual disks, Docker images and similar, you should add the -S option.
  • The --numeric-ids option will disable mapping of user and group names, numeric group and user IDs will be transfered instead. This is useful when backing up over SSH or when using a live system to backup different system disk.
  • Choosing --info=progress2 option instead of -v will show overal progress info and transfer speed instead of huge list of files.

If you wish to restore the backup use the same rsync command that was executed, but with the source and destination reversed.

Boot requirements

Having a bootable backup can be useful in case the filesystem becomes corrupt or if an update breaks the system. The backup can also be used as a test bed for updates, with the testing repo enabled, etc. If you transferred the system to a different partition or drive and you want to boot it, the process is as simple as updating the backup's /etc/fstab and your bootloader's configuration file.

Update the fstab

Without rebooting, edit the backup's fstab to reflect the changes:

tmpfs        /tmp          tmpfs     nodev,nosuid             0   0

/dev/sda1    /boot         ext2      defaults                 0   2
/dev/sda5    none          swap      defaults                 0   0
/dev/sda6    /             ext4      defaults                 0   1
/dev/sda7    /home         ext4      defaults                 0   2

Because rsync has performed a recursive copy of the entire root filesystem, all of the sda mountpoints are problematic and booting the backup will fail. In this example, all of the offending entries are replaced with a single one:

tmpfs        /tmp          tmpfs     nodev,nosuid             0   0

/dev/sdb1    /             ext4      defaults                 0   1

Remember to use the proper device name and filesystem type.

Update the bootloader's configuration file

This section assumes that you backed up the system to another drive or partition, that your current bootloader is working fine, and that you want to boot from the backup as well.

For Syslinux, all you need to do is duplicate the current entry, except pointing to a different drive or partition.

Tip: Instead of editing syslinux.cfg, you can also temporarily edit the menu during boot. When the menu shows up, press the Tab key and change the relevant entries. Partitions are counted from one, drives are counted from zero.

For GRUB, it is recommended that you automatically re-generate the main configuration file.

Also verify the new menu entry in /boot/grub/grub.cfg. Make sure the UUID is matching the new partition, otherwise it could still boot the old system. Find the UUID of a partition as follows:

# lsblk -no NAME,UUID /dev/sdb3

where you substitute the desired partition for /dev/sdb3. To list the UUIDs of partitions grub thinks it can boot, use grep:

# grep UUID= /boot/grub/grub.cfg

First boot

Reboot the computer and select the right entry in the bootloader. This will load the system for the first time. All peripherals should be detected and the empty folders in / will be populated.

Now you can re-edit /etc/fstab to add the previously removed partitions and mount points.

See also