XJDIC is an electronic Japanese-English dictionary program designed to operate in the X11 window environment.
xjdic should be run on a terminal with JIS, Shift-JIS or EUC-JP encoding.
There are different ways to get one. I'll describe only three, using rxvt-unicode, kterm or xterm. If neither of them suits you, try to set one of those encodings in your favorite terminal, it may work too.
Note: Due too its design, xjdic will work on almost any terminal with any encoding, you'll just get garbage in place of japanese characters. Due to design of most terminals, you'll get something right after you set the correct encoding. That "something" may look good (if you're lucky), awful or be just empty spaces — the latter two meaning you lack some required fonts.
Rxvt-unicode has shown the best perfomance for me so far. I recomend sticking with it unless you have something against rxvt-family terminals. Unlike kterm, it's all-purpose unicode terminal and you can use it for other things beside xjdic.
Encoding is controlled by LC_CTYPE environment variable. The command to start xjdic should look like this:
LC_CTYPE=ja_JP.EUC-JP urxvt -T 'xjdic' -e xjdic_sa -j e
The value of LC_CTYPE must be a valid locale, see Configuring Locales.
To get nice-looking characters, you must list apropriate wide font in *font resource. Sample configuration using Markus Kuhn's usc-fonts:
urxvt*font: -misc-fixed-bold-r-normal--18-120-100-100-c-90-iso10646-1,\ -misc-fixed-medium-r-normal--18-120-100-100-c-90-iso10646-1,\ -misc-fixed-medium-r-normal-ja-18-120-100-100-c-180-iso10646-1 urxvt*boldFont: urxvt*italicFont: urxvt*boldItalicFont:
I prefer having bold font for European alphabets; if you like medium instead, use something like this:
urxvt*font: -misc-fixed-medium-r-normal--18-120-100-100-c-90-iso10646-1,\ -misc-fixed-medium-r-normal-ja-18-120-100-100-c-180-iso10646-1 urxvt*boldFont: -misc-fixed-bold-r-normal--18-120-100-100-c-90-iso10646-1
Put these lines to your .Xresources (or .Xdefaults, depending on your setup). Alternatively, you can use apropriate command-line switches, see urxvt(1).
Kterm is rather limited terminal emulator designed specifically to handle Japanese. xjdic probably will be the only reason you'll keep it in your system. On the other hand, it's "home terminal" for xjdic, and usually there's no need to set up anything for kterm if you have apropriate fonts installed:
kterm -rv -e xjdic_sa
Default Arch installation contains necessary fonts (misc/jis* from xorg-fonts-misc). If you experience font-related problems, try using -fr and -fk options with some availables **-jisx0208.*-* font.
Xterm uses external program, luit, to handle different encodings. It should be as good as urxvt, but unfortunately luit is awfully buggy, especially when it comes to fancy Japanese encodings — segfaults with Shift-JIS are common and mouse paste sometimes works incorrectly in EUC-JP. Try it if xterm is your primary terminal, but be prepared to switch to something else.
Sample font configuration using ucs-fonts:
xterm*utf8: 1 xterm*font: -misc-fixed-bold-r-normal--18-120-100-100-c-90-iso10646-1 xterm*boldfont: -misc-fixed-bold-r-normal--18-120-100-100-c-90-iso10646-1 xterm*widefont: -misc-fixed-medium-r-normal-ja-18-120-100-100-c-180-iso10646-1 xterm*locale: true
Command to run xjdic:
xterm -en euc-jp xjdic_sa -j e
Read xjdic24.inf (located in
/usr/share/doc/xjdic if you used PKGBUILD from AUR) before
running xjdic — it's not the kind of program you can use without reading documentation.
You must install at least edict and kanjidic to get xjdic working.
And you'll probably need to make your own
~/.xjdicrc file. Start by copying system-wide