ASUS Zenbook UX303

From ArchWiki
Revision as of 10:01, 3 May 2015 by Foxbunny (talk | contribs) (Graphics: Mention that secondary card is for LN model only)
Jump to: navigation, search

This page contains instructions, tips, pointers, and links for installing and configuring Arch Linux on the ASUS Zenbook UX303 Ultrabook.

There is a lot a models but 2 main models, UX303LN with 2 graphic cards (intel & nvidia) and UX303LA with only an intel graphic card.

Installation problems

None, but you should use the UEFI archlinux installation guide. The Asus UEFI accepts UEFI boot (which works well) and Legacy BIOS mode.


Hard Disk

For models with an SSD, see Solid_State_Drives.

For the models without a SSD as main disk, the hard disk stop/start each 30/60 seconds, add a udev rule :

 $ cat /etc/udev/rules.d/50-hdparm.rules
 # Configure hardisk power management: No more spin-down !!
 KERNEL=="sda", SUBSYSTEM=="block", ACTION=="add", RUN+="/usr/bin/hdparm -B 255 -S 0 /dev/sda"

and update the systemd hdparm service:

 $ cat /etc/systemd/system/hdparm.service 
 Description=Local system resume actions
 ExecStart=/usr/bin/hdparm -B 255 -S 0 /dev/sda


The touchpad is a FocalTech model, that is supported by the arch reference kernel since 4.0.1-1 update.

 dmesg | grep FLT01                                                            
 [    0.395565] pnp 00:06: Plug and Play ACPI device, IDs FLT0101 SYN0a00 SYN0002 PNP0f03 PNP0f13 PNP0f12 (active)
 cat /sys/bus/acpi/devices/FLT0101\:00/status                                  
 $ xinput   
 ⎡ Virtual core pointer                    	id=2	[master pointer  (3)]
 ⎜   ↳ FocalTechPS/2 FocalTech FocalTech Touchpad	id=14	[slave  pointer  (2)]

To get full functionality, you will need to configure the touchpad. See Touchpad Synaptics for more information.

The sensitivity settings may need to be adjusted. If touchpad is not responsive, try changing the settings:

Section "InputClass"
	Option "FingerLow" "30"
	Option "FingerHigh" "35"

Touch screen

The touchscreen is an Atmel maXTouch Digitize. Simple touch works well out of the box. The 10-point multi touch works with libinput installed (tested with the tools/event-debug libinput test tool).


The webcam is an SuYin HF1019-T838-SN03 (USB 2.0, UVC) which works well.


The wifi chipset is an Intel(R) Dual Band Wireless N 7260, REV=0x144. It works well with recents kernel (fails with 3.2.0 kernel) with the iwlwifi kernel module and the firmware version The device name is wlp2s0.


The Bluetooth chipset is an intel N7260 model (same as the wifi chipset), which works well. Uses the intel/ibt-hw-37.7.10-fw- firmware.


The main graphic chipset is an Intel Haswell chipset, which works well with the i915 xorg driver. See Intel_graphics for details.

 $ lspci
 00:02.0 VGA compatible controller: Intel Corporation Haswell-ULT Integrated Graphics Controller (rev 0b)

Secondary graphics card is NVIDIA GeForce 840M (UX303LN model).

 $ lspci
 03:00.0 3D controller: NVIDIA Corporation GM108M [GeForce 840M] (rev a2)

The secondary card is combined with the main graphics in a hybrid NVIDIA Optimus configuration. The card works with nvidia drivers from the official repository. Bumblebee can be used to take advantage of the NVIDIA card.

Keyboard backlight

Four level positions (0 to 3) available with

 tee /sys/class/leds/asus::kbd_backlight/brightness <<< 3

Monitor backlight

available with

 tee  /sys/class/backlight/intel_backlight/brightness  <<< 500

825 is the max value.

On kernel 3.17, max value seems to be 187

QHD monitor

Some models include a 3200x1800 screen, which display very tiny characters.

Gnome3 is able to work out the correct font size on this display, but other environments and GUI toolkits may need adjustment. See the general HiDPI wiki page for possible fixes.


Prior to Linux 4.0.1-1, this laptop had problems resuming from suspend-to-ram, and could not reliably power off. Since Linux 4.0.1-1, these issues no longer exist and suspending/resuming as well as powering off work reliably. Suspend key (Fn+F1) works out of the box with expected behavior.


Battery has a design capacity of 4429mAh, and is able to provide just over 3 hours of autonomy under normal circumstances (average load of around 0.3 and WiFi enabled, brightness lowered to mid-range) without serious power saving tweaks. Battery stops charging when it reaches near-full capacity on AC and acpi tool will show "discharging at zero rate" message. This behavior can be observed on a brand new battery. ACPI tools are able to correctly detect the battery state.

 # on AC near-full capacity
 $ acpi -i
 Battery 0: Discharging, 98%, discharging at zero rate - will never fully discharge.
 Battery 0: design capacity 4429 mAh, last full capacity 4076 mAh = 92%
 # on AC charging
 $ acpi -i
 Battery 0: Charging, 94%, 00:11:53 until charged
 Battery 0: design capacity 4429 mAh, last full capacity 4110 mAh = 92%
 # off AC
 $ acpi -i
 Battery 0: Discharging, 98%, 03:22:03 remaining
 Battery 0: design capacity 4429 mAh, last full capacity 4076 mAh = 92%

Battery life may depend on the type of LCD panel. The above values are shown for the model with QHD display.


Microphone works out of the box. If you cannot record or use VoIP, make sure the microphone is not muted.

Function Keys

All function keys except the backlight and "plane" mode seem to work out of the box (as of kernel 3.17). To fix, add acpi_osi= as a kernel parameter. Example line from /etc/default/grub: