From ArchWiki
Revision as of 20:33, 14 November 2014 by Jstjohn (talk | contribs) (xcalib: improve grammar)
Jump to navigation Jump to search

Screen brightness might be tricky to control. On some machines physical hardware switches are missing and software solutions may not work well. However, it is generally posssible; be sure to use a method that works for your hardware.

There are many ways to adjust the screen backlight of a monitor, laptop or integrated panel (such as the iMac) using software, but depending on hardware and model, sometimes only some options are available. This article aims to summarize all possible ways to adjust the backlight.


There are many ways to control brightness. According to this discussion and this wiki page [1] the control method could be divided into these categories:

  • brightness is controlled by vendor-specified hotkey and there is no interface for the OS to adjust the brightness.
  • brightness is controlled by the either by ACPI or the graphic driver.
  • brightness is controlled by HW register through setpci.

All methods are exposed to the user through /sys/class/backlight and xrandr/xbacklight can choose one method to control brightness. It is still not very clear which one xbacklight prefers by default.

Note: See FS#27677 for xbacklight, if you get "No outputs have backlight property." There is a temporary fix if xrandr/xbacklight does not choose the right directory in /sys/class/backlight: You can specify the one you want in xorg.conf by setting the "Backlight" option of the Device section to the name of that directory (see at the bottom of the page for details).


The brightness of the screen backlight is adjusted by setting the power level of the backlight LEDs or cathodes. The power level can often be controlled using the ACPI kernel module for video. An interface to this module is provided via a folder in the sysfs at /sys/class/backlight.

The name of the folder depends on the graphics card model.

# ls /sys/class/backlight/

A backlight to adjust example: is managed by an Intel graphics card. It is called acpi_video0 on an ATI card. In the following example, acpi_video0 is used.

The directory contains the following files and folders:

actual_brightness  brightness         max_brightness     subsystem/    uevent             
bl_power           device/            power/             type

The maximum brightness can be found by reading from max_brightness, which is often 15.


The brightness can be set by writing a number to brightness. It is not possible to go any higher than the maximum brightness.

# tee /sys/class/backlight/acpi_video0/brightness <<< 5

Kernel command-line options

Sometimes, ACPI does not work well due to different motherboard implementations and ACPI quirks. This includes some laptops with dual graphics (e.g. Nvidia/Radeon dedicated GPU with Intel/AMD integrated GPU). On Nvidia Optimus laptops, the kernel parameter nomodeset can interfere with the ability to adjust the backlight. Additionally, ACPI sometimes register its own acpi_video0 backlight even if one already exists (such as intel_backlight), which results in non working backlight keys. You can try adding the following kernel parameters in your bootloader to stop ACPI from registering its own backlight interface if one already exists:


This is the default as of linux 3.16. If that does not work, you can try to adjust the list of supported OS interfaces:

acpi_osi="!Windows 2012"
Tip: On an Asus notebooks you might also need to do:
# modprobe asus-nb-wmi
Note: Disabling legacy boot on Dell XPS13 breaks backlight support.

Udev rule

If the ACPI interface is available, the backlight level can be set at boot using a udev rule.

# Set backlight level to 8
SUBSYSTEM=="backlight", ACTION=="add", KERNEL=="acpi_video0", ATTR{brightness}="8"

The systemd-backlight service restores the previous backlight brightness level at boot, whereas this rule sets it to a fixed value. If you want to use this rule, it is necessary to mask the system-backlight service, as explained in #systemd-backlight service.

Switching off the backlight

Switching off the backlight (for example when one locks the notebook) can be useful to conserve battery energy. Ideally the following command inside of a graphical session should work:

sleep 1 && xset dpms force off

The backlight should switch on again on mouse movement or keyboard input. If the previous command does not work, there is a chance that vbetool works. Note, however, that in this case the backlight must be manually activated again. The command is as follows:

vbetool dpms off

To activate the backlight again:

vbetool dpms on

For example, this can be put to use when closing the notebook lid as outlined in the entry for Acipd.

systemd-backlight service

The systemd package includes the service systemd-backlight@.service, which is enabled by default and "static". It saves the backlight brightness level at shutdown and restores it at boot. The service uses the ACPI method described in Backlight#ACPI, generating services for each folder found in /sys/class/backlight/. For example, if there is a folder named acpi_video0, it generates a service called systemd-backlight@backlight:acpi_video0.service. When using other methods of setting the backlight at boot, it is recommended to mask the service systemd-backlight@.service.

Backlight utilities


You can adjust the backlight through the xorg-server command xbacklight. The utility is provided by the xorg-xbacklight package in [extra].

A useful demonstration was posted by gotbletu on YouTube. He suggests the following commands to adjust the backlight up and down:

xbacklight -inc 40
xbacklight -dec 40
Tip: These commands can be bound to keyboard keys as described in Extra keyboard keys in Xorg.


Set screen backlight brightness dependent on power source type; with udev rule backlight is adjusted on change of power source. Requires graphic driver support for ACPI in /sys/class/backlight. Install with the AUR package power-backlight-gitAUR.


More information can be found on the Light page.


relight is available in Xyne's repos and as package relightAUR in the AUR. The package provides relight.service, a systemd service to automatically restore previous backlight settings during reboot along using the ACPI method explained above, and relight-menu, a dialog-based menu for selecting and configuring backlights for different screens.

setpci (use with great care)

It is possible to set the register of the graphic card to adjust the backlight. It means you adjust the backlight by manipulating the hardware directly, which can be risky and generally is not a good idea. Not all of the graphic cards support this method.

When using this method, you need to use lspci first to find out where your graphic card is.

# setpci -s 00:02.0 F4.B=0


The software calise can be found in AUR.

It basically computes ambient brightness, and set screen's correct backlight, simply making captures from the webcam, for laptop without light sensor. For more information, calise has its own wiki: Calise wiki.

The main features of this program are that it is very precise, very light on resource usage, and with the daemon version (.service file for systemd users available too), it has practically no impact on battery life.


Macbook-inspired brightdAUR automatically dims (but does not put to standby) the screen when there is no user input for some time. A good companion of Display Power Management Signaling so that the screen does not blank out in a sudden.


KDE users can adjust the backlight via System Settings > Power Management > Energy Saving. If you want to set backlight before kdm just put in /usr/share/config/kdm/Xsetup :

xbacklight -inc 10

Color correction


Note: xcalib does not change the backlight power, it just modifies the video LUT table: this means that your battery life will be unaffected by the change. Nevertheless, it could be useful when no backlight control is available (Desktop PCs). Use xcalib -clear to reset the LUT.

The package xcalibAUR (upstream URL) is available in the AUR and can be used to dim the screen. A demonstration video is available on YouTube. This program can correct gamma, invert colors, and reduce contrast, the latter of which we use in this case. For example, to dim down:

$ xcalib -co 40 -a

This program uses ICC technology to interact with X11 and while the screen is dimmed, you may find that the mouse cursor is just as bright as before.


The program redshift in the official repositories uses randr to adjust the screen brightness depending on the time of day and your geographic position. It can also do RGB gamma corrections and set color temperatures. As with xcalib, this is very much a software solution and the look of the mouse cursor is unaffected. To execute a single quick adjustment of the brightness, try something like this:

redshift -o -l 0:0 -b 0.8 -t 6500:6500
Tip: If your longitude is west or your latitude is south, you should input it as negative.

Example for Berkeley, CA:

redshift-gtk -l 37.8717:-122.2728 

NVIDIA settings

Users of NVIDIA's proprietary drivers users can change display brightness via the nvidia-settings utility under "X Server Color Correction." However, note that this has absolutely nothing to do with backlight (intensity), it merely adjusts the color output. (Reducing brightness this way is a power-inefficient last resort when all other options fail; increasing brightness spoils your color output completely, in a way similar to overexposed photos.)

Specific models

Backlight PWM modulation frequency (Intel i915 only)

Laptops with LED backlight are known to have screen flicker sometimes. The reason for this, is that it is hard enough to dim LEDs by limiting direct current flowing through. It is easier to control brightness by switching LEDs on and off fast enough.

However, frequency of the switching (so-called PWM modulation frequency) is not high enough actually, and some people may notice flicker either explicitly or by feeling headache and eyestrain.

If you have an Intel i915 GPU, then it may be possible to adjust PWM modulation frequency to eliminate flicker.

Install intel-gpu-tools from the official repositories. Get value of the register, that determines PWM modulation frequency

# intel_reg_read 0xC8254
0xC8254 : 0x12281228

The value returned represents period of PWM modulation. So to increase PWM modulation frequency, value of the register has to be reduced. For example, to double frequency from the previous listing, execute:

# intel_reg_write 0xC8254 0x09140914

You can use online calculator to calculate desired value

Refer to dedicated topic for details

If you are using the Intel GM45 chipset use address 0x61254 instead of 0xC8254.

Inverted Brightness (Intel i915 only)


  • after installing xf86-video-intel systemd-backlight.service turns off the backlight during boot
    • possible solution: mask systemd-backlight.service
  • switching from X to another VT turns the backlight off
  • the brightness keys are inverted (i.e. turning up the brightness makes the screen darker)

This problem may be solved by adding i915.invert_brightness=1 to the list of kernel parameters.