From ArchWiki
Revision as of 23:08, 30 September 2012 by Nonix (talk | contribs) (read-write Test: import options from Securely wipe disk / reformat the options list / remove senseless '''bolding''')
Jump to: navigation, search

badblocks is a program to test for bad blocks (commonly known as sectors) on a storage device. A sector is a subdivision of a track on storage device and sectors that have become bad cannot be used because they have become permanently damaged (a bad sector can change a letter in a text file to causing a binary program to have a segmentation fault).

Storage Device Fidelity

Although there is no firm rule has been set, it is common thinking that a new drive should have zero bad sectors. Over time, bad sectors will develop on a storage device and although they are able to be defined to the file system so that they are avoided, continual use of the drive will usually result in additional bad sectors forming and are usually the harbinger of death of a hard drive. Replacement of the device is recommended.

Comparisons with Other Programs

Typical recommended practice for testing a storage device for bad sectors is to use the manufacturer's testing program. Most manufacturers have programs that do this. The main reasoning for this is that manufacturers usually have their standards built into the test programs that will tell you if the drive needs to be replaced or not. The caveat here being is that some manufacturers testing programs do not print full test results and allow a certain number of bad sectors saying only if they pass or not. Manufacturer programs, however, are generally quicker than badblocks sometimes a fair amount so.

Testing for Bad Sectors

To test for bad sectors in Linux the program badblocks is typically used. badblocks had several different modes to be able to detect bad sectors.

read-write Test

This test is primarily for testing new drives and is a read-write test - it will destroy any data on the device. It is an extensive test with four passes using four different patterns 0xaa, 0x55, 0xff, 0x00 (hexadecimal) that on some devices will take a couple days to complete.

# badblocks -wsv /dev/<device>


do a destructive write test
show progress-bar
be "verbose" and output bad sectors detected to stdout

Additional options you might consider:

-p <number>
<number> is the number of passes
-o </path/to/output-file>
print bad sectors to <output-file> instead of stdout
-t <test_pattern> 
Specify a pattern. See below.

define specific test pattern

From the manpage: "The <test_pattern> may either be a numeric value between 0 and ULONG_MAX-1 inclusive [...]."

Badblocks can be made to repeatedly write a single "random pattern" with the -t random option.

Warning: This is not secure for cryptographic purposes. A "random pattern" is a contradiction in itself. As badblocks does not (like urandom) apply sophisticated procedures to reuse entropy but simply repeats one "random pattern" it should not be used where random data would be needed, e.g. for block device encryption.

read-write Test (non-destructive)

This test is designed for devices with data already on them. A non-destructive test writes a random pattern to a sector, reads the sector to verify the write, and then writes what was on the original sector. This is a single pass test and is useful as a general maintenance test.

# badblocks -nsv /dev/<device>

The -n option signifies a non-destructive test.

Have File System Incorporate Bad Sectors

To not use bad sectors they have to be known by the filesystem.

During Filesystem Check

Incorporating bad sectors can be done using the filesystem check utility (fsck). fsck can be told to use badblocks during a check. To do a read-write (non-destructive) test and have the bad sectors made known to the filesystem run:

# fsck -vcck /dev/<device-PARTITION>

The -cc option tells run fsck in non-destructive test mode, the -v tells fsck to show its output, and the -k option preserves old bad sectors that were detected.

To do a read-only test (not recommended):

# fsck -vck /dev/<device-PARTITION>

During Filesystem Creation

Alternately, this can be done at filesystem creation time by first finding the file systems block size. For example for ext# filesystems:

# dumpe2fs /dev/<device-PARTITION> | grep 'Block size'

feed this to badblocks and save its output:

# badblocks -b <block size> -ns -o badblocks.txt /dev/<device-PARTITION>

Then re-create the file system with the information:

# mkfs.<filesystem-type> -l badblocks.txt /dev/<device-PARTITION>