Difference between revisions of "Dell Inspiron 1521"

From ArchWiki
Jump to: navigation, search
m (Broadcom Corporation BCM4311)
m (Broadcom Corporation BCM4311)
Line 64: Line 64:
 
Then I edited the MODULES in the file /etc/rc.conf:
 
Then I edited the MODULES in the file /etc/rc.conf:
 
  MODULES=(!b43 wl b44 ... )
 
  MODULES=(!b43 wl b44 ... )
!b43 means that this module shouldn't be loaded.</br>
+
!b43 means that this module shouldn't be loaded.
wl is the new module.</br>
+
 
b44 is the wired network.</br>
+
wl is the new module.
The sequence must be correct.</br>
+
 
 +
b44 is the wired network.
 +
 
 +
The sequence must be correct.
  
 
For getting the network up automatically I copied the file /etc/network.d/examples/wpa.example (take the example-file for your use-case)
 
For getting the network up automatically I copied the file /etc/network.d/examples/wpa.example (take the example-file for your use-case)

Revision as of 23:26, 3 January 2009


The following is what I have found while using Arch on my Inspiron 1521. User experience may vary.

Hardware Specifications

lspci Output

00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge
00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx)
00:05.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 1)
00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3)
00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA
00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0)
00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1)
00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2)
00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3)
00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4)
00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI)
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14)
00:14.1 IDE interface: ATI Technologies Inc SB600 IDE
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series]
03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05)
03:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22)
03:01.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12)
03:01.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12)
0b:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01)

lsusb Output

Bus 006 Device 001: ID 1d6b:0002  
Bus 003 Device 001: ID 1d6b:0001  
Bus 001 Device 001: ID 1d6b:0001  
Bus 002 Device 001: ID 1d6b:0001  
Bus 005 Device 001: ID 1d6b:0001  
Bus 004 Device 001: ID 1d6b:0001 

Kernel

The stock Arch kernel works just fine.

Networking

My Network was extremly slow. This was cause a ipv6-Problem. After adding the following line in the /etc/modprobe.conf everything was ok.

alias net-pf-10 off

Wired

Works out of the box.

Wireless

Broadcom Corporation BCM4311

First I installed yaourt: Yaourt

Then I installed the package broadcom-wl:

yaourt -S broadcom-wl

Then I edited the MODULES in the file /etc/rc.conf:

MODULES=(!b43 wl b44 ... )

!b43 means that this module shouldn't be loaded.

wl is the new module.

b44 is the wired network.

The sequence must be correct.

For getting the network up automatically I copied the file /etc/network.d/examples/wpa.example (take the example-file for your use-case) into the directory /etc/network.d/ and renamed it (eg. wlan_profile) and edited it. Then I added the following line to /etc/rc.conf:

NETWORKS=(wlan_profile)

And added the following Deamon in the /etc/rc.conf:

DAEMONS=( ... net-profiles ... )

Modem

I have not tried the modem to see if it works.

Xorg

Example Dell_Inspiron_1521/xorg.conf