Dell Mini 10v
Template:Article summary start Template:Article summary text Template:Article summary heading Template:Article summary wiki Template:Article summary wiki Template:Article summary wiki Template:Article summary wiki Template:Article summary end
Before you begin
This article is intended to assist users with the specifics of installing Arch Linux on the Dell Mini 10v. It is assumed that a user is also following an installation guide such as the Beginners' Guide.
Dell Mini 10v hardware may vary, however the following list of hardware has been assumed in this article:
- Intel Corporation 82801G card
- Realtek ALC272 Chip (from alsamixer)
- Intel Corporation Mobile 945GME
- Wired NIC
- Realtek RTL8101E/RTL8102E
- Wireless NIC
- Broadcom Corporation BCM4312 802.11b/g
- Dell 365 Bluetooth 2.1+EDR
- Syntek Integrated Webcam
To list hardware, issue this command:
$ lspci && lsusb
The Dell Mini 10v does not have an optical drive. This means you will need to install Arch Linux through one of the alternative methods:
- USB stick (recommended)
- External USB CD-ROM drive.
To select the required boot media to install Arch Linux, press Template:Keypress to open the Boot Menu when booting the Dell Mini 10v.
Install the correct video driver:
# pacman -S xf86-video-intel
The synaptics package is required to use the touchpad. For help refer to the Synaptics guide. Manual configuration is needed as follows to ignore movements, scrolling and tapping on the bottom section of the touchpad, where the touchpad buttons are located.
Firstly install the synaptics package:
# pacman -S xf86-input-synaptics
Once X has been restarted, the bottom part of the touchpad will be disabled, allowing a user to click without unintentional movements of the mouse. See the synaptics manual page for available options:
$ man synaptics
The Wireless NIC is supported by the b43 module and is included in kernel from 2.6.32 on. Firmware must be installed for this hardware, as outlined in the Wireless Setup article.
If you have difficulty with connection, or have unstable connection, try the option
when loading the b43 module. This can be done with
rmmod b43 # remove the module modprobe b43 qos=0 # reload it with the option
Once confirming that it works, you can create a file /etc/modprobe.d/b43.conf with the following line
options b43 qos=0
For utilities to monitor the battery status, see the Laptop article.
Suspend to RAM
# pacman -S pm-utils acpid
The acpid package handles events such as pressing the the power button or closing the laptop lid. For more information, see the Acpid article. To suspend to RAM, edit Template:Filename to tell the acpid package to call the pm-suspend script (part of pm-utils), when an event such as closing the laptop lid occurs. Below, Template:Codeline has been added to the button/lid and button/power sections:
The netbook will now suspend to RAM when the laptop lid is closed or power button pressed. To wake the netbook, open the lid or press the power button once more.
It may happen that the resume takes more than 5 seconds of black screen before coming back. This may be caused by the b43 firmware loading delay. A close inspection of 'dmesg' should reveal the cause: check the line containing 'b43-phy0' to see if reload it takes a long time. If so, create a file /etc/pm/config.d/modules and add Template:File This should reduce the resume time significantly to the extent that the graphical display comes back almost instantaneously.
Sound and Microphone
Sound can be set up as outlined in the ALSA section of Beginners' Guide. The microphone and speaker can be unmuted and volume increased by using alsamixer:
Firstly, press Template:Keypress+Template:Keypress to view both Playback and Capture cards. Now press Template:Keypress to unmute Master, PCM, Mic and Capture. Arrows can be used to select the channel and increase volume.
To save these ALSA settings, issue this command:
# alsactl store
The inbuilt webcam works out of the box, with the latest kernel. You may use the Template:Package Official package to test the webcam, however this package depends on Template:Package Official. Also check that the normal user is a member of the video group:
$ groups $USER
Follow the Bluetooth article for setting up Bluetooth.
SD card reader
The SD card reader works out of the box.
For maximising performace of a SSD, refer to this article.