Difference between revisions of "Dell Vostro 1000"

From ArchWiki
Jump to: navigation, search
(Wireless: outdated (even referred to explicit versions), just point readers to the main pages)
m (Adjust Brightness: removed useless/outdated section)
Line 103: Line 103:
And '''DONE''', you can suspend and resume with pm-utils normally.
And '''DONE''', you can suspend and resume with pm-utils normally.
=Adjust Brightness=
Adjust normally with the FN Keys if your using the kernel 2.6.24 or greater

Revision as of 14:39, 9 September 2015

  • Use Kernel 2.6.24 or greater
  • Use install disc 2008.03 or greater (see install)

Questions: IM diogo.urb@hotmail.com (MSN) .


Device Status Modules
Ati Radeon Xpress Working fglrx (cataylst), radeon
Ethernet Working b44
Wireless Working broadcom-wlAUR, b43, ndiswrapper
Audio Working snd_hda_intel
Modem Untested
PCMCIA Slot Untested
Card Reader Working


"Unknown Key Pressed"

  • You may occasionally run across an error (occurring in an extremely high frequency) in your messages.log/dmesg:
 atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
 atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
  • The fix for this issue is fairly simple. Power down your dell laptop, and reseat the battery.
  • Another possible cause may be due to your AC adapter being unplugged from the outlet, yet attached to the back of your laptop.
  • Yet another suggested fix for the problem is updating your BIOS.. but since this is an extreme measure (found on the ubuntu forums.. so take it with a grain of salt), try the first two solutions before moving on to this potentially dangerous measure.

High Temperature

After the installation you will see that the temperature is around 60°C (Too High). You can get the temperature through:

cat /proc/acpi/thermal_zone/THRM/temperature


cat /proc/acpi/thermal_zone/THM/temperature

This is because the CPU frequency is at full usage always... so before continuing with the install process install cpufrequtils, you can see further details on Cpufrequtils

  • Note: using lm_sensors 'sensors' utility, k8temp-pci-00c3 reports much more reasonable temperatures (more along the lines of what windows reports) compared to this Virtual Thermal Zone. I have noticed no issues running without cpu scaling while on AC.


Follow the Installation guide or the Beginners' guide.


Follow Xorg, Touchpad Synaptics and Extra keyboard keys.


Follow Wireless network configuration and Broadcom wireless.


  • Suspend and Hibernate works with pm-utils
  • Also works by issuing
    echo mem > /sys/power/state

Resume not working after suspend to RAM

To workaround this issue edit the file


and add the following to the kernel boot line:


Backlight doesn't come back after Resume

Tango-view-refresh-red.pngThis article or section is out of date.Tango-view-refresh-red.png

Reason: radeontool no longer exists (Discuss in Talk:Dell Vostro 1000#)

You may need a workaround because the backlight doesn't come back after Resuming.

Install Pm-utils, and create this file:

case $1 in
  echo "Suspending to disk!"
  echo "Suspending to RAM"
  echo "Suspend to disk is over, Resuming. .."
  echo "Suspend to RAM is over, Resuming..."
  radeontool light on
  radeontool dac on
 *)  echo "somebody is calling me totally wrong."
# chmod +x /etc/pm/sleep.d/radeonlight

Now to make it work you need radeontool.

And DONE, you can suspend and resume with pm-utils normally.