Dell XPS 13 (9360)
|USB-C / Thunderbolt 3||Working||?|
|Fingerprint sensor||Not working||?|
The Dell XPS 13 Late 2016 (9360) is the fourth-generation model of the XPS 13 line. The laptop is available since October (pre-2017 model) in both a standard edition with Windows installed as well as both a pre-2017 model and a 2017 model (with insignificant hardware differences) Developer Edition with Ubuntu 16.04 "SP1" installed, featuring kernel 4.8 as of now. There is only minor hardware differences between them, mostly in regards to the mainboard microchip manufacturers. Just like the older versions (9333, 9343 and 9350) it is available in different hardware configurations as well. These fourth gen models includes Intel's Kaby Lake CPUs and advertised with up to 16GB LPDDR 1866 MHz RAM and a 1TB PCI SSD. It will now also be available in Rose Gold. Prior to previous information and current specifications available provided by Dell (at least to regular customers), it is not available with the 2133 MHz RAM speed. However, in some models, including those available to employees and possibly Dell partners (and/or business customers), memory speed is indeed available up to 2133 Mhz LPDDR3 (non-upgradable). The same mentioned models are also available with the Intel Core i7-7660U (aswell as i7-7560U) with the Intel 640 Iris Plus onboard graphics. Respective clock frequencies are 2.5 Ghz (up to 4GHz in Turbo-mode) and 2,4 Ghz (up to 3.8 Ghz), respectively.
The installation process for Arch on the XPS 13 does not differ from any other PC. For installation help, please see the Installation guide and UEFI. This page covers the current status of hardware support on Arch, as well as post-installation recommendations.
As of kernel 4.5, the Intel Kaby Lake architecture is supported.
- 1 Content Adaptive Brightness Control
- 2 Power Saving
- 3 Video
- 4 Wireless
- 5 Bluetooth
- 6 Thunderbolt 3 / USB 3.1
- 7 SATA controller
- 8 Touchpad
- 9 Touchscreen
- 10 Keyboard Backlight
- 11 Hidden Keyboard Keys
- 12 Firmware Updates
- 13 Sleep to idle (s2idle, S0ix)
- 14 Troubleshooting
- 14.1 EFISTUB does not boot
- 14.2 Not waking from suspend
- 14.3 Power Drain after waking from standby
- 14.4 Popping sound on headphones/external speakers
- 14.5 Crackling sound with screen changes
- 14.6 Coil Whine
- 14.7 Freezing after waking from suspend
- 14.8 Continuous hissing sound with headphones
- 14.9 Blank screen issue after booting
- 15 Fingerprint sensor
- 16 See Also
Content Adaptive Brightness Control
In the XPS 13 the display panels (both FHD and QHD+) come with Content Adaptive Brightness Control (usually referred to as CABC or DBC) embedded in the panel firmware - it adjusts the screen brightness depending on the content displayed on the screen. While it saves a bit of power, it is generally undesirable, especially for Linux users who are likely to be switching between dark and light screen content. Dell has issued a fix for this, however it is only available to run in Windows. The fix is available directly from Dell.
To test if your XPS 13 is affected by the CABC, go to this test page. It is possible to apply Dell's firmware update using a portable Windows 10 on a USB device:
- Install (for example) AUR
- Download a Windows 10 ISO from Microsoft's website
- Create a portable Windows 10 installation using woeusb
- Boot the XPS 13 from your Windows 10 USB device (F12)
- In Windows, download and install the latest driver for the Intel Graphics controller
- Then download and install this tool to update the panel firmware. The tool gives you the option to disable CABC
- Reboot (from USB)
- Reboot to Arch Linux and rerun the test
It's possible to save around ~10/20% energy with somes tricks.
Disabling SD-Card reader
The SD-Card adapter can be disabled in BIOS settings to save ~0.5W.
It's possible to undervolt CPU and GPU with intel-undervolt
This is an example of best stable values for a I5-7200u (depend of your cpu):
CPU (0): -160.16 mV GPU (1): -125.00 mV CPU Cache (2): -89.84 mV
Edit the config file
$ nano /etc/intel-undervolt.conf
This is an example for i5-7200u
# CPU Undervolting undervolt 0 'CPU' -160 undervolt 1 'GPU' -125 undervolt 2 'CPU Cache' -90 undervolt 3 'System Agent' 0 undervolt 4 'Analog I/O' 0 # Daemon Update Interval interval 5000
then enable/start the daemon :)
$ systemctl enable intel-undervolt $ systemctl start intel-undervolt
NVM Express SSD
For some devices it might be necessary to set a higher value for the
nvme_core.default_ps_max_latency_us parameter to enable all power saving states. This parameter has to be set on the kernel command line.
For the Toshiba 512GB SSD used in some models of the XPS 13 the value to enable all states is 170000 (the combined latency of entering and leaving the highest power state, add
nvme_core.default_ps_max_latency_us=170000 to your kernel command line). For the 1TB SSD this valued should be increased to 180000 instead. To check if all states are enabled you can use the AUR package, which provides the
# nvme get-feature -f 0x0c -H /dev/nvme0 get-feature:0xc (Autonomous Power State Transition), Current value:0x000001 Autonomous Power State Transition Enable (APSTE): Enabled Auto PST Entries ................. Entry[ 0] ................. Idle Time Prior to Transition (ITPT): 1500 ms Idle Transition Power State (ITPS): 3 ................. Entry[ 1] ................. Idle Time Prior to Transition (ITPT): 1500 ms Idle Transition Power State (ITPS): 3 ................. Entry[ 2] ................. Idle Time Prior to Transition (ITPT): 1500 ms Idle Transition Power State (ITPS): 3 ................. Entry[ 3] ................. Idle Time Prior to Transition (ITPT): 8500 ms Idle Transition Power State (ITPS): 4 .................
If the power states are enabled there should be values for ITPT and ITPS in the first entries. Also the ITPS-value of the last filled entry should be the highest power saving-state of the SSD (which can be viewed using
smartctl -a /dev/nvme0 or
nvme id-ctrl /dev/nvme0).
For the HD 620 graphics card the following modules are working: (see Intel graphics#Module-based options)
The first argument is to enable modesetting if it's not set by default. The second argument is needed to activate framebuffer compression power savings. These values should work well!
This argument is used to enable GuC updates. GuC is a small proprietary binary blob released by intel to update the GuC binary in faster intervals than the kernel release does. It is used for graphics workload scheduling on the various graphics parallel engines. More details at (https://01.org/linuxgraphics/downloads/firmware). The GuC binary for kaby lake is included since firmware release linux-firmware 20170217 in the official repository. HuC is also a binary blob from intel. It's designed to offload some of the media functions from the CPU to GPU. As of kernel 4.12, HuC is loaded if GuC is enabled. One can check with 'cat /sys/kernel/debug/dri/0/i915_huc_load_status' and 'cat /sys/kernel/debug/dri/0/i915_guc_load_status'.
Panel Self Refresh (PSR) is working for eDP 1.3 and up and does stop the creation of new frames when the screen content is static to save energy. If you experience problems with PSR try to set 'disable_power_well=0' or disable otherwise. It may also be required to add the
modconf hook to Mkinitcpio to avoid a hang after resume on both Xorg and Wayland.
enable_psr==1where on first boot or after resume the panel stays black once reaching the desktop environment, only refreshing after switching to and from a tty. In this case it is required to simply remove the option.
NOT WORKING: semaphores=1
The semaphore option is NOT working for kaby lake CPUs and won't enable even if you set the option to 1.
If you have the QHD+ (3200x1800) model, also check out HiDPI for UI scaling configurations.
But there might be video issues left for this model. Please help by contributing any feedback about similar issues you might have experience(d) to this bugreport (https://bugs.freedesktop.org/show_bug.cgi?id=100671).
The Killer 1535 Wirless Adapter is functional and the ath10k firmware is included in recent linux kernel versions. The connection speed reported by iw is limited to 1-6Mbits/s. However this is just the output being wrong. The real connection speed is not limited to this value.
Some users are experiencing issues, where the connection is dropped under heavy load but reconnects within a brief moment. This might not be noticed during browsing at all but becomes apparent in online games. There is a firmware update proposed by DELL to fix the issue, but it might not fix all the issues. In at least one case the new firmware did not fix the connection loss / low connection speed problem. Signs of this problem seems to be two kinds of messages in dmesg:
pcieport 0000:00:1c.4: AER: Corrected error received: id=00e4 pcieport 0000:00:1c.4: PCIe Bus Error: severity=Corrected, type=Data Link Layer, id=00e4(Transmitter ID) pcieport 0000:00:1c.4: device [8086:9d14] error status/mask=00001000/00002000 pcieport 0000:00:1c.4:  Replay Timer Timeout
CPU: 3 PID: 1410 Comm: irq/133-ath10k_ Not tainted Hardware name: Dell Inc. XPS 13 9360/0839Y6, BIOS 2.1.0 08/02/2017 Call Trace: <IRQ> dump_stack+0x63/0x82 __warn+0xcb/0xf0 warn_slowpath_null+0x1d/0x20 net_rx_action+0x274/0x3a0 ? irq_finalize_oneshot.part.35+0xe0/0xe0
As of February 2018, Dell support suggests to update the firmware of the network adapter in the following way:
- Confirm that you have QCA6174 checking the output of
- Download the latest firmware and extract the contents from git
- Substitute the
/lib/firmware/ath10k/with the one downloaded
- Inside the new folder, rename
- Reboot and test the new Killer Wi-Fi firmware
Update: Internet connection dropped even with the firmware from the above fix. Using the newer firmware
firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1 by downloading that file from https://github.com/kvalo/ath10k-firmware/blob/master/QCA6174/hw3.0/4.4.1.c1/firmware-6.bin_RM.4.4.1.c1-00042-QCARMSWP-1, copying it to
/usr/lib/firmware/ath10k/QCA6174/hw3.0/ and renaming it to
firmware-6.bin fixes this.
Reboot and verify that this newer firmware is used by verifying that
dmesg | grep ath outputs:
ath10k_pci 0000:3a:00.0: firmware ver RM.4.4.1.c1-00042-QCARMSWP-1 api 6 features wowlan,ignore-otp crc32 40fb7bdd
BIOS version 2.9.0 manages to make these crashes occur no matter what firmware you load. Updating to at least version 2.10.0 resolves this issue. Alternatively, installing an Intel WiFi card solves the problem.
After following the instructions given at Bluetooth tethering of internet connections via phone works immediately.
Thunderbolt 3 / USB 3.1
The USB-C port supports Thunderbolt 3, Displayport-over-USB-C and USB power delivery as well as USB 3.1.
Ethernet repeatedly disconnects/reconnects with Dell USB-C adapter (DA200)
Use of a power management package (such as TLP) may cause the ethernet adapter to repeatedly disconnect and reconnect. If this happens, disable/blacklist USB autosuspend for the ethernet adapter. (On my laptop, this is the device Bus 004 Device 007: ID 0bda:8153 Realtek Semiconductor Corp in the output of lsusb.)
Also disabling or reducing power of wifi may help: http://en.community.dell.com/support-forums/network-internet-wireless/f/3324/t/19995423
USB-C Compatibility Chart
Thunderbolt Firmware updates
The thunderbolt controller in the laptop has an embedded firmware. The laptop ships with firmware version NVM 18, and the most recent available version from Dell's website is NVM 26. If encountering compatibility problems with Thunderbolt accessories (such as the DA-200), the firmware may need to be updated. If you have fwupd (see: #Firmware Updates) set up then you should receive this update automatically. Otherwise, you can install it manually as follows.
Dell maintained a github repository with the firmware, but abandoned it now that the firmware is on LVFS. The current version is available as
0x075B_secure.bin (or 0x082A for newer model, see instructions below) inside the Windows package. This can be extracted with .
Here is a short list of steps to update the Thunderbolt-Firmware on linux 4.13+ (use at your own risk):
- Force enable the thunderbolt controller (or plug in a device to enable it)
# echo 1 | sudo tee /sys/bus/wmi/devices/86CCFD48-205E-4A77-9C48-2021CBEDE341/force_power
- Check your model ID. If it's 0x082A, use the 0x082A firmware instead of the 0x075B one.
# cat /sys/bus/thunderbolt/devices/0-0/device
- Flash the 9360 firmware from the thunderbolt-nvm-linux repository to a non active NVME memory spot
# dd if=payloads/0x075B.bin of=/sys/bus/thunderbolt/devices/0-0/nvm_non_active0/nvmem
- Trigger the update process
# echo 1 > /sys/bus/thunderbolt/devices/0-0/nvm_authenticate
- At this point, your screen should flickr a couple of time. Verify that the update is done by checking that authenticate returns 0
# cat /sys/bus/thunderbolt/devices/0-0/nvm_authenticate
- Verify the new nvme version (it should return 26.1)
# cat /sys/bus/thunderbolt/devices/0-0/nvm_version
- Put the controller back in normal mode
# echo 0 | sudo tee /sys/bus/wmi/devices/86CCFD48-205E-4A77-9C48-2021CBEDE341/force_power
When the SATA-controller is set to
RAID On in BIOS, the SSD is not recognized, because the kernel does not support remapped AHCI device, see . Set to
AHCI before attempting to install Arch.
The touchpad has no explicit buttons. The button is built into the pad's surface. There is a small line printed on the pad separating left/right click areas, and libinput does the same separation in software.
Libinput also provides a middle button – to issue a middle click, simply press on the middle area right between the virtual left and right buttons (i.e. on the small printed separator line).
Remove psmouse errors from dmesg
dmesg | grep -i psmouse returns an error, but your touchpad still works, then it might be a good idea to disable
psmouse. First create a config file:
# nano /etc/modprobe.d/modprobe.conf blacklist psmouse
Then add this file to
... FILES=(/etc/modprobe.d/modprobe.conf) ...
Rebuild your initial ramdisk image (see Mkinitcpio#Image creation and activation).
The touchscreen works without additional configuration. The bug resulting in a disabled touchscreen after resume was fixed with kernel 4.8.5.
Refer to libinput#Gestures for information about the current development state and available methods.
Scrolling in Firefox
See Firefox/Tweaks#Pixel-perfect trackpad scrolling. This enables both touchscreen scrolling and high-res trackpad scrolling.
By default, the keyboard backlight turns off after 10 seconds of inactivity. Some users might find this too short and annoying. The delay can be increased (or decreased) by editing this file:
You can also change the brightness (0-2) by editing the following file. This is identical to pressing F10 on your keyboard:
Hidden Keyboard Keys
There are additional Fn+<Key> (sequences) that are not marked at all on the keyboard but underlying hardware generates them anyway. Here they are (if you find more add them to the table below):
|Fn+<Key>||Resulting key (sequence)|
|Fn+A / D / E / F / G / T / Q / W||XF86Launch3|
If enabled in BIOS, pressing Fn+F7 will disable sound, keyboard and screen backlight, the charging LED and the LED on the power button. Unfortunately there seems to be no way to disable just the LEDs- some users recommend black electrical tape. The output of `smbios-token-ctl -d` only list changes related to screen, keyboard and sound when unobtrusive mode is active.
Dell provides firmware updates via fwupd. Please note if you have used a bind mount partition for /boot or are booting via legacy BIOS/CSM instead of UEFI, you will not be able to use the fwupd utility - instead use the method below.
Alternatively, the BIOS update can be downloaded from the Dell website (filter by "BIOS") and placed in a location accessible to the firmware. This could be the '/boot' folder, or a FAT32 formatted USB stick. Then restart your laptop and hit F12 while starting. In the boot menu choose firmware update and select the downloaded file.
Sleep to idle (s2idle, S0ix)
According to the method described in an Intel article, this device supports Low Power S0 Idle (S0ix).
To try S0ix, write
/sys/power/state (see Power management/Suspend and hibernate). The system should behave like it is sleeping, except the power button light is on. Press power button to wake up.
S0ix can be used as an alternative to "Sleep to RAM", by changing the following systemd configuration:
[Sleep] SuspendState=freeze mem standby
You may need to prevent the xHCI controller from waking up the system. Write
/proc/acpi/wakeup, or write
/sys/devices/pci0000:00/0000:00:14.0/power/wakeup. Different models may have different PCI ID for the xHCI controller, see the 4th column of
grep XHC /proc/acpi/wakeup.
To make the change permanent, put a file to
w /sys/devices/pci0000:00/0000:00:14.0/power/wakeup - - - - disabled
If you want to enable waking up by key press, see Dell XPS 13 2-in-1 (9365)#Suspend issues.
EFISTUB does not boot
The BIOS does not pass any boot parameters to the kernel. Use a UEFI boot loader instead.
It is possible to work around this issue by bulding single file EFI images containing the parameters. See .
Not waking from suspend
Update the BIOS to 1.0.7 to patch this issue.
Power Drain after waking from standby
Some users recognised ~2W more power consumption after waking up from standby. Go to the UEFI Firmware Settings (tap the F2 key when the Dell logo appears) and uncheck the 'Enable Thunderbolt Boot Support'. You may useor AUR to reproduce and check this behaviour yourself.
Popping sound on headphones/external speakers
Power saving being enabled on the audio chip will cause the hissing and popping to appear.
If you are using
/etc/default/tlp and disable it.
Crackling sound with screen changes
Some users experienced a weird crackling, white noise sound when the display is changing its contents after waking the computer from S3 sleep..
This issue should be patched as of the 4.14.15 kernel.
If you're still encountering this issue, try manually applying this patch. Adding the kernel parameter
i915 enable_guc=1 as described in Intel graphics might also help, however multiple people have reported that this does not fix the problem completely.
Unfortunately Dell still did not fix this issue and the sound for my model was very loud. The issue seems to be connected to the graphic card. For some users, it is possible to reduce it a lot by activating frame buffer compression "enable_fbc=1" Intel graphics#Framebuffer compression (enable_fbc). The coil whine will then start again under heavy graphic load. For the touchscreen model, this may be very often, due to the high resolution screen. In a similar vein, the display can be run at a lower resolution, again reducing the load on the graphics card.
Freezing after waking from suspend
Installing reported to fix this.AUR is
Continuous hissing sound with headphones
Open alsamixer and set "Headphone Mic Boost" gain to 10 dB (See discussion on reddit). Note that this does reduce the volume slightly.
You may also run the equivalent command:
$ amixer -c PCH cset 'name=Headphone Mic Boost Volume' 1
PulseAudio will rewrite these ALSA settings. So if you use PulseAudio you should change its config to make them permanent:
[Element Headphone Mic Boost] required-any = any switch = select # Replace "volume = merge" by: volume = 1 override-map.1 = all override-map.2 = all-left,all-right
[Element Headphone Mic Boost] switch = off # Replace "volume = off" by: volume = 1
Blank screen issue after booting
If using "late start" KMS (the default) and the screen goes blank when loading modules, it may help to add
intel_agp to the initramfs or using a special kernel parameter. Consult Intel graphics#Blank screen during boot, when "Loading modules" for more information about the kernel parameter way and have a look at Kernel mode setting#Early KMS start for a guide on how to setup the modules for the initramfs.
Dell officially does not support fingerprint reader functionality , however an effort on reverse engineering the protocol of Validity 138a:0090, 138a:0094, 138a:0097 fingerprint readers can be found at github .