Dell XPS 13 (9360)
|Wireless||Working - limited||ath10k|
|USB-C / Thunderbolt 3||Working||?|
The Dell XPS 13 Late 2016 (9360) is the fourth-generation model of the XPS 13 line. The laptop is available since October in both a standard edition with Windows installed as well as a Developer Edition with Ubuntu installed. There is no hardware difference between them. Just like the older versions (Dell XPS 13, Dell XPS 13 (2015)), Dell XPS 13 (2016)) it will be available in different hardware configurations. This fourth gen model includes Intel's Kaby Lake CPU and configurable with up to 16GB RAM and a 1TB PCI SSD. It will now also be available in Rose Gold.
The installation process for Arch on the XPS 13 does not differ from any other PC. For installation help, please see the Installation guide and UEFI. This page covers the current status of hardware support on Arch, as well as post-installation recommendations.
As of kernel 4.5, the Intel Kaby Lake architecture is supported.
Content adaptive brightness control
In the XPS 13 the display panels (both FHD and QHD+) come with adaptive brightness embedded in the panel firmware, this "content adaptive brightness control" (usually referred to as CABC or DBC) will adjust the screen brightness depending on the content displayed on the screen and will generally be found undesirable, especially for Linux users who are likely to be switching between dark and light screen content. Dell has issued a fix for this however it is only available to run in Windows and for the QHD+ model of the laptop so this precaution should be taken before installing Linux, the FHD model of the XPS 13 (9360) cannot be fixed. This is not a problem with the panel but rather a problem with the way the panels are configured for the XPS 13, as the same panel exists in the Dell's Latitude 13 7000 series (e7370) FHD model but with CABC disabled. The fix is available directly from Dell.
NVM Express SSD
NVME Power Saving Patch
Andy Lutomirski has released version 4 of his patchset which fixes powersaving for NVME devices in linux. Currently, this patch is not merged into mainline yet. Until it lands in mainline kernel use the AUR package below. Linux-nvme — Mainline linux kernel patched with Andy's patch for NVME powersaving APST.
Blank screen issue after booting
If using "late start" KMS (the default) and the screen goes blank when loading modules, it may help to add
intel_agp to the initramfs or using a special kernel parameter. Consult Intel graphics#Blank screen during boot, when "Loading modules" for more information about the kernel paramter way and have a look at Kernel mode setting#Early KMS start for a guide on how to setup the modules for the initramfs.
The Killer 1535 Wirless Adapter is functional and the ath10k firmware is incluced in recent linux kernel versions. The connection speed however is limited to 1Mb/s at the moment. This was the case for the Ubuntu 10.04 shipped with the Developer Edition and also with a standard Arch Linux installation.
Thunderbolt 3 / USB 3.1
The USB-C port supports Thunderbolt 3, Displayport-over-USB-C and USB power delivery as well as USB 3.1.
When the SATA-controller is set to
RAID On in Bios, the hard disk (at least the SSD) is not recognized. Set to
AHCI is recommended) before attempting to install Arch.
Remove psmouse errors from dmesg
dmesg | grep -i psmouse returns an error, but your touchpad still works, then it might be a good idea to disable
psmouse. First create a config file:
# nano /etc/modprobe.d/modprobe.conf blacklist psmouse
Then add this file to
... FILES="/etc/modprobe.d/modprobe.conf" ...
Rebuild your initial ramdisk image (see Mkinitcpio#Image creation and activation).
Refer to libinput#Gestures for information about the current development state and available methods.