Ext4 - результат эволюции файловой системы ext3. Ext4 в сравнении с ext3 сильнее улучшена, чем ext3 по сравнению с ext2. В ext3 практически просто добавили журналирование, а ext4 изменена более кардинально. В результате получилась ФС с улучшенным дизайном, производительностью, стабильностью, и расширенными возможностями.
Source: Ext4 - Linux Kernel Newbies
- 1 Создание раздела ext4 с нуля
- 2 Migrating From ext3 to ext4
- 3 Tips and tricks
- 4 Troubleshooting
Создание раздела ext4 с нуля
- Обновите систему: Template:Codeline
- Отформатируйте раздел: Template:Codeline (замените Template:Codeline устройством, которое собрались форматировать (например Template:Codeline))
- Монтируйте раздел
- Добавьте пункт в Template:Filename, в качестве типа ФС укажите ext4
Migrating From ext3 to ext4
There are two ways of migrating partitions from ext3 to ext4:
- mounting ext3 partitions as ext4 without converting (compatibility)
- converting ext3 partitions to ext4 (performance)
These two approaches are described below.
Mounting ext3 Partitions as ext4 Without Converting
A compromise between fully converting to ext4 and simply remaining with ext3 is to mount existing ext3 partitions as ext4.
- Compatibility (the filesystem can continue to be mounted as ext3) – This allows users to still read the filesystem from other distributions/operating systems without ext4 support (e.g. Windows with ext3 drivers)
- Improved performance (though not as much as a fully-converted ext4 partition) – See Ext4 - Linux Kernel Newbies for details
- Fewer features of ext4 are used (only those that do not change the disk format such as multiblock allocation and delayed allocation)
- Edit Template:Filename and change the 'type' from ext3 to ext4 for any partitions you would like to mount as ext4.
- Re-mount the affected partitions.
Converting ext3 Partitions to ext4
To experience the benefits of ext4, an irreversible conversion process must be completed.
- Improved performance and new features – See Ext4 - Linux Kernel Newbies for details
- Read-only access from Windows can be provided by Ext2Explore, but there is currently no driver for writing data.
- Irreversible (ext4 partitions cannot be 'downgraded' to ext3)
The following software is required on the Arch Linux system:
If converting one's /boot partition to ext4:
- Template:Codeline (with ext4 patch)
If converting one's root (/) partition to ext4:
If converting one's root (/) partition to ext4, the following software is also needed on a bootable CD/USB drive:
These instructions were adapted from http://ext4.wiki.kernel.org/index.php/Ext4_Howto and http://bbs.archlinux.org/viewtopic.php?id=61602. They have been tested and confirmed by this author as of January 16, 2009.
- UPGRADE! Perform a sysupgrade to ensure all required packages are up-to-date: Template:Codeline
- BACK-UP! Back-up all data on any ext3 partitions that are to be converted to ext4. Although ext4 is considered 'stable' for general use, it is still a relatively young and untested file system. Furthermore, this conversion process was only tested on a relatively simple setup; it is impossible to test each of the many possible configurations the user may be running.
- Edit Template:Filename and change the 'type' from ext3 to ext4 for any partitions that are to be converted to ext4.
- The conversion process with Template:Codeline must be done when the drive is not mounted. If converting one's root (/) partition, the simplest way to achieve this is to boot from some other live medium, as described in the 'Prerequisites' section above.
- Reboot Arch Linux!
Migrating files to extents
Even though the filesystem is now converted to ext4, all files that have been written before the conversion do not yet take advantage of the new extents of ext4, which will improve large file performance and reduce fragmentation and filesystem check time. In order to fully take advantage of ext4, all files would have to be rewritten on disk. A utility called e4defrag is being developed and will take care of this task ; however, it is not yet ready for production.
Fortunately, it is possible to use the chattr program, which will cause the kernel to rewrite the file using extents. It is possible to run this command on all files and directories of one partition (e.g. if /home is on a dedicated partition): (Must be run as root)
find /home -xdev -type f -print0 | xargs -0 chattr +e find /home -xdev -type d -print0 | xargs -0 chattr +e
It is recommended to test this command on a small number of files first, and check if everything is going all right. It may also be useful to check the filesystem after conversion.
Using the lsattr command, it is possible to check that files are now using extents. The letter 'e' should appear in the attribute list of the listed files.
Tips and tricks
Remove reserved blocks
By default 5% of a filesystem will be flagged as reserved for root user. For modern high-capacity disks, this is much higher than necessary - particularly if the partition is not being used for system files. It is generally safe to reduce the percentage of reserved blocks to free up disk space when the partition is either
- Very large (for example >50 G)
- Not being used for system files
Use the tune2fs utility to do this. The command below would set the percentage of reserved blocks on the partition /dev/sdXY to 1%:
tune2fs -m 1 /dev/sdXY
One problem this author encountered was a kernel panic after converting the root (/) partition to ext4. This is because the initial ramdisk was detecting the partition as 'ext4dev', rather than 'ext4'. It was a simple matter to boot with the 'fallback' initial ramdisk and re-create the 'default' initial ramdisk :
- Remount the root partition in read-write mode; assuming 'XXX' is your root partition :
# mount /dev/XXX / -o remount,rw
- Manually mount the boot partition on /boot if it is on a separate partition.
- Re-create the ramdisk :
# mkinitcpio -p kernel26
During the creation process, Template:Codeline correctly detected and included ext4 modules in the initial ramdisk.
Some early adopters of ext4 encountered data corruption after a hard reboot. Please read Ext4 data loss; explanations and workarounds for more information.
Since kernel 2.6.30, ext4 is considered "safe(r)." Several patches improved the robustness of ext4 - albeit at a slight performance cost. A new mount option (Template:Codeline) can be used to disable this behavior. For more information, please read Linux 2 6 30 - Filesystems performance improvements.
Since kernel 2.6.30, ext4 performance has decreased due to changes that serve to improve data integrity. Users can improve performance with the Template:Codeline option when mounting the disk, but this can be dangerous and may result in data loss or corruption after power failures. To turn barriers off, add the option Template:Codeline to the desired filesystem in Template:Filename. For example:
# /dev/sda5 / ext4 noatime,barrier=0 0 1
E4rat is a preloading application designed for ext4. It monitors files opened during boot, optimizes their placement on the partition to improve access time, and preloads them at the very begining of the boot process.