Difference between revisions of "Flashing BIOS from Linux"

From ArchWiki
Jump to: navigation, search
(Created page with 'Category:HOWTOs (English) This article aims on providing information on flashing your system BIOS under Linux. Most manufacturers provide a Windows executable or a BIOS execu…')
 
m (Added recommendation from Dell (see https://github.com/dell/biosdisk/pull/1))
 
(95 intermediate revisions by 46 users not shown)
Line 1: Line 1:
[[Category:HOWTOs (English)]]
+
[[Category:Mainboards and BIOS]]
 +
[[ja:Linux から BIOS を書き換える]]
 
This article aims on providing information on flashing your system BIOS under Linux. Most manufacturers provide a Windows executable or a BIOS executable that can only be run under Windows. However, there are a few utilities, that allow you to upgrade your system BIOS under Linux.
 
This article aims on providing information on flashing your system BIOS under Linux. Most manufacturers provide a Windows executable or a BIOS executable that can only be run under Windows. However, there are a few utilities, that allow you to upgrade your system BIOS under Linux.
  
==Introduction==
+
{{Warning|Flashing motherboard BIOS is a dangerous activity that can render your motherboard inoperable! While the author of this article has successfully run this procedure many times, your mileage may vary. Be careful! You may want to consider updating [[microcode]] instead if it is supported by your system.}}
There are a couple of utilities that you can use to flash the system BIOS.
 
  
==BiosDisk==
+
{{Note|HP users may download Windows BIOS updater from HP website, extract *.exe file and locate ISO image for burning to a CD. Using CD, upgrade is possible from BIOS menu using 'Firmware Upgrade' without using below tools. See [https://h30434.www3.hp.com/t5/Notebook-Operating-System-and-Recovery/How-to-update-BIOS-on-Linux/td-p/4869835 this] thread for details.}}
[http://linux.dell.com/projects.shtml#biosdisk BiosDisk] BiosDisk simplifies the process of flashing your system BIOS under Linux
 
===Installation===
 
====Method 1: AUR (Recommended)====
 
[http://aur.archlinux.org/packages.php?ID=38248 BiosDisk] is available from the Arch User Community Repositories.
 
  
====Method 2: From Source====
+
{{Note|For users with Dell computers, Dell recommends Linux users flash their BIOS following information located  [https://www.dell.com/support/article/us/en/19/sln171755/updating-the-dell-bios-in-linux-and-ubuntu-environments here].}}
Grab the source from the [http://linux.dell.com/biosdisk/ biosdisk] web page. Extract the source from the tar ball and run the install.sh file as root.
 
  
===Usage===
+
== BiosDisk ==
 +
[https://github.com/dell/biosdisk BiosDisk] BiosDisk simplifies the process of flashing your system BIOS under Linux
 +
 
 +
=== Installation ===
 +
[[Install]] the {{AUR|biosdisk-git}} package.
 +
 
 +
=== Usage ===
 
To use the biosdisk utility to create a BIOS flash image, first download the latest raw BIOS image for your system from your manufacturer's website. Make sure however, that you always get the BIOS executable and NOT the Windows executable. You then have one of several options: create a floppy, create a dd floppy image, create a user-installable distribution-specific package (e.g. RPM), or actually install the image for your bootloader.
 
To use the biosdisk utility to create a BIOS flash image, first download the latest raw BIOS image for your system from your manufacturer's website. Make sure however, that you always get the BIOS executable and NOT the Windows executable. You then have one of several options: create a floppy, create a dd floppy image, create a user-installable distribution-specific package (e.g. RPM), or actually install the image for your bootloader.
  
 
* The mkfloppy action will create the biosdisk image and write it directly to a floppy disk. Usage is the following:
 
* The mkfloppy action will create the biosdisk image and write it directly to a floppy disk. Usage is the following:
+
 
 
     biosdisk mkfloppy [-o option] [-d device] [-k baseimage] /path/to/.exe  
 
     biosdisk mkfloppy [-o option] [-d device] [-k baseimage] /path/to/.exe  
+
 
* The mkimage action will create a floppy image on the user's hard drive. Usage is the following:  
+
* The mkimage action will create a floppy image on the user's hard drive. Usage is the following:
+
 
 
     biosdisk mkimage [-o option] [-i destination] [-k baseimage] /path/to/.exe  
 
     biosdisk mkimage [-o option] [-i destination] [-k baseimage] /path/to/.exe  
+
 
 
* The mkpkg action will create the floppy image, and use it to create a user-installable package specific to the distribution (example: RPM). When the package is installed, it will use the distribution's built-in tools to update the system's bootloader so that the user can boot to the image from the hard drive to flash the BIOS, without needing a floppy drive. Currently only Red Hat/Fedora RPM packages are supported. Usage is as follows:
 
* The mkpkg action will create the floppy image, and use it to create a user-installable package specific to the distribution (example: RPM). When the package is installed, it will use the distribution's built-in tools to update the system's bootloader so that the user can boot to the image from the hard drive to flash the BIOS, without needing a floppy drive. Currently only Red Hat/Fedora RPM packages are supported. Usage is as follows:
+
 
 
     biosdisk mkpkg [-o option] [--install] [--distro=] [--name=] [--version=] [--release=] /path/to/{.exe | .img}
 
     biosdisk mkpkg [-o option] [--install] [--distro=] [--name=] [--version=] [--release=] /path/to/{.exe | .img}
+
 
 
* The install action will create the biosdisk image, copy the image file to /boot, and then update the bootloader with an entry for the image. Then all the user has to do is boot the system and select the image to flash the BIOS; this will load the biosdisk image directly from the hard drive and flash the BIOS.
 
* The install action will create the biosdisk image, copy the image file to /boot, and then update the bootloader with an entry for the image. Then all the user has to do is boot the system and select the image to flash the BIOS; this will load the biosdisk image directly from the hard drive and flash the BIOS.
+
 
 
     biosdisk install [-o option] [--name=] /path/to/{.exe | .img}
 
     biosdisk install [-o option] [--name=] /path/to/{.exe | .img}
  
==Flashrom==
+
== Flashrom ==
 
[http://www.flashrom.org/Flashrom Flashrom]is a utility for identifying, reading, writing, verifying and erasing flash chips. It is designed to flash BIOS/EFI/coreboot/firmware/optionROM images on mainboards, network/graphics/storage controller cards, and various programmer devices.
 
[http://www.flashrom.org/Flashrom Flashrom]is a utility for identifying, reading, writing, verifying and erasing flash chips. It is designed to flash BIOS/EFI/coreboot/firmware/optionROM images on mainboards, network/graphics/storage controller cards, and various programmer devices.
  
===Installation===
+
{{Warning|If you have a laptop/notebook/netbook, please do NOT try flashrom because interactions with the EC on these machines might crash your machine during flashing. flashrom tries to detect if a machine is a laptop, but not all laptops follow the standard, so this is not 100% reliable.[https://www.flashrom.org/Board_Testing_HOWTO]}}
====Method 1: Community Repo (Recommended)====
 
sudo pacman -S flashrom
 
  
====Method 2: AUR====
+
=== Installation ===
[http://aur.archlinux.org/packages.php?ID=30391 Flashrom]
 
[http://aur.archlinux.org/packages.php?ID=23390 Flashrom]
 
[http://aur.archlinux.org/packages.php?ID=36865 Flashrom] is also available from the Arch User Community Repositories.
 
  
====Method 2: From Source====
+
[[Install]] the {{pkg|flashrom}} or {{AUR|flashrom-svn}}{{Broken package link|package not found}} package.
Grab the source from the [http://www.flashrom.org/Flashrom Flashrom] web page. Extract the source from the tar ball and run make and make install.
 
  
===Usage===
+
=== Usage ===
Find out if your motherboard and chipset is supported by flashrom at this website. [http://www.flashrom.org/Supported_hardware Supported Hardware]
+
Find out if your motherboard and chipset (internal) is supported by flashrom at this website. [http://www.flashrom.org/Supported_hardware Supported Hardware]
 
You can also find out if your hardware is supported by issuing the following command
 
You can also find out if your hardware is supported by issuing the following command
  sudo flashrom
+
  # flashrom --programmer internal
The above command will tell you your motherboard and chipset. You can then find out if your's is supported by issuing this command
+
 
  flashrom -L | grep whatevernameyougotfromthefirstcommand
+
The above command will tell you your motherboard and chipset. You can then find out if yours is supported by issuing this command:
 +
  # flashrom --programmer internal -L | grep CHIPNAMEfrompreviouscommand
 +
 
 +
On modern mainboards you probably get more than one rom chip listed. You have to select the chipname you get from the upper command. Then you use the {{ic|-c}} option to select which rom is affected by the command
 +
# flashrom --programmer internal -c "CHIPNAME" -r backup_CHIPNAME.bin
 +
 
 +
Write and verify the new BIOS image (proprietary or Coreboot) on the ROM chip:
 +
# flashrom --programmer internal internal -c "CHIPNAME" -w newbios.bin
 +
 
 +
If you want to flash other flash chips on your mainboard, you will find all options with
 +
# flashrom
 +
 
 +
{{Note|1=With Linux kernel versions greater than 4.4, CONFIG_IO_STRICT_DEVMEM a new kernel security measure can make flashrom stop working, in that case you can try adding "iomem=relaxed" to your kernel parameters. [https://www.flashrom.org/FAQ  FAQ].}}
 +
 
 +
== FreeDOS ==
 +
[http://www.freedos.org/ FreeDOS] a free DOS-compatible operating system, is up to the challenge, no need for proprietary DOS versions. So, all you need is a bootable floppy disk image with FreeDOS kernel on it.
 +
 
 +
=== Unetbootin ===
 +
By far the easiest way to make a bootable FreeDOS USB Stick is using {{pkg|unetbootin}}, available in the [[Official repositories]].
 +
 
 +
You should format a pendrive with FAT16 and flag it as "boot" (you may do this through a GUI with {{Pkg|gparted}}, {{AUR|qtparted}}{{Broken package link|{{aur-mirror|qtparted}}}} or {{Pkg|partitionmanager}}). Then, after mounting the flash drive, select under distribution '''FreeDOS''' and your mounted stick. The app will automatically download the image for you and copy it to the drive. Finally, you may copy everything you want to flash there (BIOS, firmwares, etc).
 +
 
 +
{{Warning|Unetbootin may not function properly on some Lenovo systems. It may be necessary to create the bootable stick on a different device. See [http://reboot.pro/topic/9849-blinking-cursor-at-boot/ here].}}
 +
 
 +
=== Gentoo ===
 +
Check out [https://wiki.gentoo.org/wiki/BIOS_Update#FreeDOS_environment FreeDOS Flash Drive] on the Gentoo Wiki if you want to create a bootable FreeDOS Flash drive.
 +
 
 +
=== Prebuilt images ===
 +
 
 +
Yet another simple solution: [http://chtaube.eu/computers/freedos/bootable-usb/ FreeDOS prebuilt bootable USB flash drive image by Christian Taube]{{Dead link|2017|07|11}}
 +
 
 +
=== Using a FreeDOS-provided Disk Image + USB stick ===
 +
 
 +
As of writing (2017-07-11), {{pkg|unetbootin}} doesn't support versions of FreeDOS more recent than 1.0 (current version is 1.2). The following procedure worked to upgrade an Inspiron 17-3737 to the A09 BIOS. (Dell offers this as a possibility [http://www.dell.com/support/article/ca/en/cabsdt1/SLN171755/updating-the-dell-bios-in-linux-and-ubuntu-environments?lang=EN#Creating%20a%20USB%20Bootable%20Storage%20Device on their site])
 +
 
 +
Some notes before starting:
 +
 
 +
* You can check your current BIOS version with {{pkg|dmidecode}}. You might already be at the latest version.
 +
* Ensure that your hardware vendor has verified this method works (use of FreeDOS to run BIOS update <code>.exe</code>)
 +
* Laptop users should not attempt this without AC power
 +
* This is dangerous, and you assume all risk for following this procedure.
 +
 
 +
Procedure:
 +
 
 +
# Grab the latest USB installer from the [http://www.freedos.org/download/ FreeDOS Download Page]
 +
#* author note: used the "Full" version on suspicion that it might include more drivers, etc (pure speculation)
 +
# Extract the archive, you get a <code>.img</code> file
 +
# Determine which of <code>/dev/sdX</code> is your USB stick (use <code>fdisk -l</code>)
 +
# Write the image directly to the block device:
 +
#* <code>dd if=FD12FULL.img of=/dev/sdX status=progress</code> (where <code>X</code> is the letter representing your USB stick as a block device, don't write the image to a partition)
 +
# Double-check that the image copying worked:
 +
#* <code>fdisk -l</code> (you should see a single partition on a DOS disk with the bootable ("boot") flag set)
 +
# Mount the partition, and copy over the <code>.exe</code> used to update your firmware
 +
#* Stay on the safe side and limit the filename to 8 characters (without extension), upper case
 +
#* Ensure that you verified any checksums provided by your hardware vendor
 +
# Unmount and reboot. Do whatever is needed to boot from the USB drive
 +
 
 +
Now you will find yourself in the FreeDOS live installation environment.
 +
 
 +
# Select your language
 +
# You will be prompted to install FreeDOS
 +
#* Select "No - Return to DOS"
 +
# You should see a prompt (<code>C:\></code>)
 +
# Run <code>dir /w</code> and verify that your firmware upgrade tool is present
 +
# Run the executable
 +
#* author note: in the case of the Dell tool, the machine displayed a spash screen and then rebooted. Upon reboot, it started the firmware upgrade automatically, and ran for about 2 minutes with the fan at full speed)
 +
# Once the process specific to your vendor completes, optionally verify through the BIOS setup screen, as well as by running {{pkg|dmidecode}} when you're back in linux
 +
 
 +
=== Images that are too large for a floppy ===
 +
If your flash image is too large for a floppy, go to the [http://www.fdos.org/bootdisks/ FreeDos bootdisk website], and download the 10Mb hard-disk image.  This image is a full disk image, including partitions, so adding your flash utility will be a little trickier:
 +
 
 +
First find the first partition (at time of writing, the first partition starts at block 63; this means that the partitions starts at offset <tt>512 * 63 = 32256</tt>).
 +
You can either use:
 +
# file -sk ''<image-file>'' | sed -r 's/.*startsector ([0-9]+).*/\1/'
 +
'''63'''
 +
 
 +
Or:
 +
 
 +
# fdisk -l ''<image-file>''
 +
 +
Units = sectors of 1 * '''512''' = 512 bytes
 +
 +
      Device  Boot  Start    End  Blocks  Id  System
 +
              *        '''63'''  19151  9544+  1  FAT12
 +
 
 +
Now you can mount the image:
 +
 
 +
# mount -oloop,offset=$((63 * 512)) ''<image-file>'' /mnt
 +
 
 +
Then you can copy your flash utility onto the filesystem as normal.
 +
Once you're done:
 +
 
 +
# umount /mnt
 +
 
 +
The image can now be copied to a USB stick for booting, or booted as a memdisk as per normal instructions.
 +
 
 +
=== Usage ===
 +
 
 +
The OEM Bootdisk version is recommended, as it only includes {{ic|kernel}} and {{ic|command.com}} thus leaving more space for the flash utility and new BIOS image. Download and decompress the FreeDOS image:
 +
 
 +
$ wget http://www.fdos.org/bootdisks/autogen/FDOEM.144.gz
 +
$ gunzip FDOEM.144.gz
 +
 
 +
Copy your BIOS flash utility and new BIOS image to the mounted floppy disk image. Load the necessary modules:
 +
 
 +
# modprobe vfat
 +
# modprobe loop
 +
 
 +
{{ic|/proc/fileystems}} shows if the needed file systems are supported. "loop mount" the floppy disk image to a temporary path:
 +
 
 +
$ mkdir /tmp/floppy
 +
$ mount -t vfat -o loop FDOEM.144 /tmp/floppy
 +
 
 +
If the mount went without errors, copy the BIOS flash utility and new BIOS image to the mounted floppy disk image. You will probably have to unzip the archive you downloaded from your motherboard vendor site, to get to those two files. For example:
 +
 
 +
# unzip 775Dual-VSTA\(2.60\).zip
 +
Archive: 775Dual-VSTA(2.60).zip
 +
  inflating: 75DVSTA2.60
 +
  inflating: ASRflash.exe
 +
# cp 75DVSTA2.60 ASRflash.exe /tmp/floppy
 +
 
 +
Check that the two files were not too big for the floppy:
 +
 
 +
Filesystem          1K-blocks      Used Available Use% Mounted on
 +
/tmp/FDOEM.144
 +
                          1424      990      434  70% /tmp/floppy
 +
Unmount the floppy disk image:
 +
 
 +
umount /tmp/floppy
 +
 
 +
The next step is to burn the floppy image to a CD/DVD-RW media, but in a way that it can be booted afterwards. First create a bootable CD image, and then burn it.
 +
 
 +
genisoimage -o bootcd.iso -b FDOEM.144 FDOEM.144
 +
wodim -v bootcd.iso
 +
 
 +
You may alternatively add your image to the [[GRUB]] menu. Install [[syslinux]] and copy {{ic|memdisk}} and your image to {{ic|/boot}}:
 +
 
 +
  cp /usr/lib/syslinux/memdisk /boot
 +
  cp FDOEM.144 /boot/flashbios.img
 +
 
 +
Now add an entry to {{ic|/boot/grub/menu.lst}}:
 +
 
 +
  title Flash BIOS
 +
  kernel /memdisk
 +
  initrd /flashbios.img
 +
 
 +
Or for GRUB2 in {{ic|/boot/grub/grub.cfg}}:
 +
 
 +
  menuentry "Flash BIOS" {
 +
  linux16 /boot/memdisk
 +
  initrd16 /boot/flashbios.img
 +
  }
 +
 
 +
Or for syslinux in {{ic|/boot/syslinux/syslinux.cfg}}:
 +
 
 +
LABEL flashbios
 +
MENU LABEL Flash BIOS
 +
LINUX ../memdisk
 +
INITRD ../fdboot.img
 +
 
 +
Finally reboot your machine, making sure the CD drive is first in the boot sequence, and run the BIOS upgrade procedure when the CD boots. If using the GRUB method, choose the new entry on the list, and it should boot into FreeDOS.
 +
 
 +
== Bootable optical disk emulation ==
 +
The script Geteltorito.pl will extract the [[wikipedia:El Torito (CD-ROM standard)|El Torito]] boot image. It has worked on Lenovo laptops like X220, X230, W540, T450 and T450s. It may work for other vendors as well.
 +
 
 +
=== Installation ===
 +
Install the {{AUR|geteltorito}} package.
 +
 
 +
=== Usage ===
 +
 
 +
Get the bios update iso from the vendor support site. Run the ''geteltorito'' image extraction:
 +
 
 +
$ geteltorito.pl -o <image>.img <image>.iso
 +
 
 +
Copy the image to the usb thumbdrive:
 +
 
 +
# dd if=<image>.img of=<destination> bs=512K
 +
 
 +
Reboot and boot from the USB drive, follow vendor directions.
 +
 
 +
{{Note|If you get the message "Secure Flash Authentication failed!", it means that some security check did not allow the flash to happen. It can help to go to the BIOS options page "Security" > "UEFI BIOS Update Option" and disable "Secure RollBack Prevention" and enable "Flash BIOS Updating by End-Users". You can set them to what you want after flashing.}}
  
Read the BIOS image into a file:
+
== fwupd ==
  $ flashrom -r backup.bin
+
fwupd is a simple daemon to allow session software to update device firmware on your local machine. It's designed for desktops, but this project is also usable on phones, tablets and on headless servers. You can either use a GUI software manager like GNOME Software to view and apply updates, the command-line tool or the system D-Bus interface directly.
Write a BIOS image (proprietary or LinuxBIOS) on the ROM chip:
 
  $ flashrom -wv newbios.bin
 
  
WARNING: This will overwrite your current BIOS! Make sure you know what you're doing! You've been forewarned !!
+
Large vendors including Dell and Logitech use this way to distribute firmware updates to Linux.
  
==
+
A list of hardware currently available in stable tree can be viewed [https://fwupd.org/lvfs/devicelist here].

Latest revision as of 17:12, 13 November 2017

This article aims on providing information on flashing your system BIOS under Linux. Most manufacturers provide a Windows executable or a BIOS executable that can only be run under Windows. However, there are a few utilities, that allow you to upgrade your system BIOS under Linux.

Warning: Flashing motherboard BIOS is a dangerous activity that can render your motherboard inoperable! While the author of this article has successfully run this procedure many times, your mileage may vary. Be careful! You may want to consider updating microcode instead if it is supported by your system.
Note: HP users may download Windows BIOS updater from HP website, extract *.exe file and locate ISO image for burning to a CD. Using CD, upgrade is possible from BIOS menu using 'Firmware Upgrade' without using below tools. See this thread for details.
Note: For users with Dell computers, Dell recommends Linux users flash their BIOS following information located here.

BiosDisk

BiosDisk BiosDisk simplifies the process of flashing your system BIOS under Linux

Installation

Install the biosdisk-gitAUR package.

Usage

To use the biosdisk utility to create a BIOS flash image, first download the latest raw BIOS image for your system from your manufacturer's website. Make sure however, that you always get the BIOS executable and NOT the Windows executable. You then have one of several options: create a floppy, create a dd floppy image, create a user-installable distribution-specific package (e.g. RPM), or actually install the image for your bootloader.

  • The mkfloppy action will create the biosdisk image and write it directly to a floppy disk. Usage is the following:
    biosdisk mkfloppy [-o option] [-d device] [-k baseimage] /path/to/.exe 
  • The mkimage action will create a floppy image on the user's hard drive. Usage is the following:
    biosdisk mkimage [-o option] [-i destination] [-k baseimage] /path/to/.exe 
  • The mkpkg action will create the floppy image, and use it to create a user-installable package specific to the distribution (example: RPM). When the package is installed, it will use the distribution's built-in tools to update the system's bootloader so that the user can boot to the image from the hard drive to flash the BIOS, without needing a floppy drive. Currently only Red Hat/Fedora RPM packages are supported. Usage is as follows:
    biosdisk mkpkg [-o option] [--install] [--distro=] [--name=] [--version=] [--release=] /path/to/{.exe | .img}
  • The install action will create the biosdisk image, copy the image file to /boot, and then update the bootloader with an entry for the image. Then all the user has to do is boot the system and select the image to flash the BIOS; this will load the biosdisk image directly from the hard drive and flash the BIOS.
    biosdisk install [-o option] [--name=] /path/to/{.exe | .img}

Flashrom

Flashromis a utility for identifying, reading, writing, verifying and erasing flash chips. It is designed to flash BIOS/EFI/coreboot/firmware/optionROM images on mainboards, network/graphics/storage controller cards, and various programmer devices.

Warning: If you have a laptop/notebook/netbook, please do NOT try flashrom because interactions with the EC on these machines might crash your machine during flashing. flashrom tries to detect if a machine is a laptop, but not all laptops follow the standard, so this is not 100% reliable.[1]

Installation

Install the flashrom or flashrom-svnAUR[broken link: package not found] package.

Usage

Find out if your motherboard and chipset (internal) is supported by flashrom at this website. Supported Hardware You can also find out if your hardware is supported by issuing the following command

# flashrom --programmer internal

The above command will tell you your motherboard and chipset. You can then find out if yours is supported by issuing this command:

# flashrom --programmer internal -L | grep CHIPNAMEfrompreviouscommand

On modern mainboards you probably get more than one rom chip listed. You have to select the chipname you get from the upper command. Then you use the -c option to select which rom is affected by the command

# flashrom --programmer internal -c "CHIPNAME" -r backup_CHIPNAME.bin

Write and verify the new BIOS image (proprietary or Coreboot) on the ROM chip:

# flashrom --programmer internal internal -c "CHIPNAME" -w newbios.bin

If you want to flash other flash chips on your mainboard, you will find all options with

# flashrom
Note: With Linux kernel versions greater than 4.4, CONFIG_IO_STRICT_DEVMEM a new kernel security measure can make flashrom stop working, in that case you can try adding "iomem=relaxed" to your kernel parameters. FAQ.

FreeDOS

FreeDOS a free DOS-compatible operating system, is up to the challenge, no need for proprietary DOS versions. So, all you need is a bootable floppy disk image with FreeDOS kernel on it.

Unetbootin

By far the easiest way to make a bootable FreeDOS USB Stick is using unetbootin, available in the Official repositories.

You should format a pendrive with FAT16 and flag it as "boot" (you may do this through a GUI with gparted, qtpartedAUR[broken link: archived in aur-mirror] or partitionmanager). Then, after mounting the flash drive, select under distribution FreeDOS and your mounted stick. The app will automatically download the image for you and copy it to the drive. Finally, you may copy everything you want to flash there (BIOS, firmwares, etc).

Warning: Unetbootin may not function properly on some Lenovo systems. It may be necessary to create the bootable stick on a different device. See here.

Gentoo

Check out FreeDOS Flash Drive on the Gentoo Wiki if you want to create a bootable FreeDOS Flash drive.

Prebuilt images

Yet another simple solution: FreeDOS prebuilt bootable USB flash drive image by Christian Taube[dead link 2017-07-11]

Using a FreeDOS-provided Disk Image + USB stick

As of writing (2017-07-11), unetbootin doesn't support versions of FreeDOS more recent than 1.0 (current version is 1.2). The following procedure worked to upgrade an Inspiron 17-3737 to the A09 BIOS. (Dell offers this as a possibility on their site)

Some notes before starting:

  • You can check your current BIOS version with dmidecode. You might already be at the latest version.
  • Ensure that your hardware vendor has verified this method works (use of FreeDOS to run BIOS update .exe)
  • Laptop users should not attempt this without AC power
  • This is dangerous, and you assume all risk for following this procedure.

Procedure:

  1. Grab the latest USB installer from the FreeDOS Download Page
    • author note: used the "Full" version on suspicion that it might include more drivers, etc (pure speculation)
  2. Extract the archive, you get a .img file
  3. Determine which of /dev/sdX is your USB stick (use fdisk -l)
  4. Write the image directly to the block device:
    • dd if=FD12FULL.img of=/dev/sdX status=progress (where X is the letter representing your USB stick as a block device, don't write the image to a partition)
  5. Double-check that the image copying worked:
    • fdisk -l (you should see a single partition on a DOS disk with the bootable ("boot") flag set)
  6. Mount the partition, and copy over the .exe used to update your firmware
    • Stay on the safe side and limit the filename to 8 characters (without extension), upper case
    • Ensure that you verified any checksums provided by your hardware vendor
  7. Unmount and reboot. Do whatever is needed to boot from the USB drive

Now you will find yourself in the FreeDOS live installation environment.

  1. Select your language
  2. You will be prompted to install FreeDOS
    • Select "No - Return to DOS"
  3. You should see a prompt (C:\>)
  4. Run dir /w and verify that your firmware upgrade tool is present
  5. Run the executable
    • author note: in the case of the Dell tool, the machine displayed a spash screen and then rebooted. Upon reboot, it started the firmware upgrade automatically, and ran for about 2 minutes with the fan at full speed)
  6. Once the process specific to your vendor completes, optionally verify through the BIOS setup screen, as well as by running dmidecode when you're back in linux

Images that are too large for a floppy

If your flash image is too large for a floppy, go to the FreeDos bootdisk website, and download the 10Mb hard-disk image. This image is a full disk image, including partitions, so adding your flash utility will be a little trickier:

First find the first partition (at time of writing, the first partition starts at block 63; this means that the partitions starts at offset 512 * 63 = 32256). You can either use:

# file -sk <image-file> | sed -r 's/.*startsector ([0-9]+).*/\1/'
63

Or:

# fdisk -l <image-file>
…
Units = sectors of 1 * 512 = 512 bytes
…
      Device  Boot  Start    End  Blocks  Id  System
              *        63  19151   9544+   1  FAT12

Now you can mount the image:

# mount -oloop,offset=$((63 * 512)) <image-file> /mnt

Then you can copy your flash utility onto the filesystem as normal. Once you're done:

# umount /mnt

The image can now be copied to a USB stick for booting, or booted as a memdisk as per normal instructions.

Usage

The OEM Bootdisk version is recommended, as it only includes kernel and command.com thus leaving more space for the flash utility and new BIOS image. Download and decompress the FreeDOS image:

$ wget http://www.fdos.org/bootdisks/autogen/FDOEM.144.gz
$ gunzip FDOEM.144.gz

Copy your BIOS flash utility and new BIOS image to the mounted floppy disk image. Load the necessary modules:

# modprobe vfat
# modprobe loop

/proc/fileystems shows if the needed file systems are supported. "loop mount" the floppy disk image to a temporary path:

$ mkdir /tmp/floppy
$ mount -t vfat -o loop FDOEM.144 /tmp/floppy

If the mount went without errors, copy the BIOS flash utility and new BIOS image to the mounted floppy disk image. You will probably have to unzip the archive you downloaded from your motherboard vendor site, to get to those two files. For example:

# unzip 775Dual-VSTA\(2.60\).zip
Archive: 775Dual-VSTA(2.60).zip
 inflating: 75DVSTA2.60
 inflating: ASRflash.exe
# cp 75DVSTA2.60 ASRflash.exe /tmp/floppy

Check that the two files were not too big for the floppy:

Filesystem           1K-blocks      Used Available Use% Mounted on
/tmp/FDOEM.144
                         1424       990       434  70% /tmp/floppy

Unmount the floppy disk image:

umount /tmp/floppy

The next step is to burn the floppy image to a CD/DVD-RW media, but in a way that it can be booted afterwards. First create a bootable CD image, and then burn it.

genisoimage -o bootcd.iso -b FDOEM.144 FDOEM.144
wodim -v bootcd.iso

You may alternatively add your image to the GRUB menu. Install syslinux and copy memdisk and your image to /boot:

 cp /usr/lib/syslinux/memdisk /boot
 cp FDOEM.144 /boot/flashbios.img

Now add an entry to /boot/grub/menu.lst:

 title Flash BIOS
 kernel /memdisk
 initrd /flashbios.img

Or for GRUB2 in /boot/grub/grub.cfg:

 menuentry "Flash BIOS" {
 linux16 /boot/memdisk
 initrd16 /boot/flashbios.img
 }

Or for syslinux in /boot/syslinux/syslinux.cfg:

LABEL flashbios
	MENU LABEL Flash BIOS
	LINUX ../memdisk
	INITRD ../fdboot.img

Finally reboot your machine, making sure the CD drive is first in the boot sequence, and run the BIOS upgrade procedure when the CD boots. If using the GRUB method, choose the new entry on the list, and it should boot into FreeDOS.

Bootable optical disk emulation

The script Geteltorito.pl will extract the El Torito boot image. It has worked on Lenovo laptops like X220, X230, W540, T450 and T450s. It may work for other vendors as well.

Installation

Install the geteltoritoAUR package.

Usage

Get the bios update iso from the vendor support site. Run the geteltorito image extraction:

$ geteltorito.pl -o <image>.img <image>.iso

Copy the image to the usb thumbdrive:

# dd if=<image>.img of=<destination> bs=512K

Reboot and boot from the USB drive, follow vendor directions.

Note: If you get the message "Secure Flash Authentication failed!", it means that some security check did not allow the flash to happen. It can help to go to the BIOS options page "Security" > "UEFI BIOS Update Option" and disable "Secure RollBack Prevention" and enable "Flash BIOS Updating by End-Users". You can set them to what you want after flashing.

fwupd

fwupd is a simple daemon to allow session software to update device firmware on your local machine. It's designed for desktops, but this project is also usable on phones, tablets and on headless servers. You can either use a GUI software manager like GNOME Software to view and apply updates, the command-line tool or the system D-Bus interface directly.

Large vendors including Dell and Logitech use this way to distribute firmware updates to Linux.

A list of hardware currently available in stable tree can be viewed here.