Difference between revisions of "Gobi Broadband Modems"

From ArchWiki
Jump to: navigation, search
(Device identification)
Line 20: Line 20:
  echo "04da 250e" > /sys/bus/usb-serial/drivers/qcserial/new_id
  echo "04da 250e" > /sys/bus/usb-serial/drivers/qcserial/new_id
  echo "04da 250f" > /sys/bus/usb-serial/drivers/qcserial/new_id
  echo "04da 250f" > /sys/bus/usb-serial/drivers/qcserial/new_id
note that this has to be repeated when you reboot/shutdown.
note that this has to be repeated when you reload the qcserial module or reboot/shutdown.

Revision as of 14:45, 14 April 2013

This is a short tutorial on connecting to the internet using your gobi modem.

Device identification

Install usbutils

pacman -S usbutils

and then examine the output of

$ lsusb

which will show the vendor and product IDs of the device.

For example, my HP un2430 modem:

Bus 001 Device 005: ID 03f0:371d Hewlett-Packard 

As of linux-3.1.1-1 the device is detected by the qcserial module, if not, you're going to have to recompile the qcserial module with your added product and vendor id.

Alternatively you can add the Product and Vendor ID by writing them into the new_id file (best both at the same time because most Gobi modules switch the Product ID when the Firmware is loaded). Here the Shell Commands i had to use (in a root shell, sudo doesnt work in this case for some reason): my integrated Gobi2K has the Vendor ID 04da and the Product IDs 250e (waiting for Firmware) and 250f (firmware loaded)

echo "04da 250e" > /sys/bus/usb-serial/drivers/qcserial/new_id
echo "04da 250f" > /sys/bus/usb-serial/drivers/qcserial/new_id

note that this has to be repeated when you reload the qcserial module or reboot/shutdown.


"gobi_loader is a firmware loader for Qualcomm Gobi USB chipsets. These devices appear in an uninitialised state when power is applied and require firmware to be loaded before they can be used as modems. gobi_loader adds a udev rule that will trigger loading of the firmware and make the modem usable." (http://www.codon.org.uk/~mjg59/gobi_loader/)

Install gobi-loader and gobi-firmware from AUR.

After installation, you should enter your product and vendor id in the /lib/udev/rules.d/60-gobi.rules

Then a simple reload of the qcserial module:

# rmmod qcserial
# modprobe qcserial



See main article: wvdial

The general procedure is to switch the device into modem mode, make sure the ttyUSB device(s) are recognized by the qcserial kernel module, and then to run wvdial to dial, connect and start pppd.

Install wvdial

# pacman -S wvdial

The configuration file /etc/wvdial.conf will in general depend on (a) which device you have (b) which mobile network you are connecting to. A single wvdial.conf file can be defined with named sections to be usable with several USB modems and networks, should you need them.

Run (as root)

# wvdialconf

which will attempt to write /etc/wvdial.conf correctly. You will need to add the user, password and Access Point Name (APN). You can obtain these (i) from your network provider, (ii) from other users via published wvdial.confs, or (iii) by logging the USB tty traffic under another operating system (Sysinternals' Portmon).

My /etc/wvdial.conf looks like this:

[Dialer status]
Init1 = AT+CPIN?
Init2 = ATI
Modem = /dev/ttyUSB1

[Dialer pin]
Modem = /dev/ttyUSB1
Init1 = AT+CPIN=1234

[Dialer wwan]
Init1 = ATZ
Init2 = AT+CGDCONT=1,"IP","data.apn.com"
Stupid Mode = yes
Phone = *99***1#
New PPPD = yes
Modem = /dev/ttyUSB1
Username = XXXXXX
Dial Command = ATDT
Password = XXXXXX
Baud = 460800

To simplify the procedure, I took my SIM card out and disabled the PIN so I don't have to run "wvdial pin" before connecting to the internet.

Often there will be several devices (at /dev/ttyUSB0, /dev/ttyUSB1, /dev/ttyUSB2 for example). If in doubt about which to use, try each of them in turn. Once the configuration files are prepared, the internet connection is established by running

$ wvdial <section>

The final wvdial command should start pppd and the obained IP address should be visible in the terminal output. At that point the internet connection should be live, which can be easily checked with a web browser or by pinging an external IP address.

Related Articles

USB 3G Modem
Huawei E220
Allow users to dial with wvdial
Internet key Momo Design
3G and GPRS modems with pppd alone
Huawei E1550 3G modem