HP Pavilion ze5600
This document applies in particular to ArchLinux on my HP Pavilion ze5615CA laptop. It also applies to the entire ze5600 series on any modern Linux system (using at least kernel 2.6.39). Feel free to contact me if any problems or suggestions (lagagnon at gmail.com) (English or Spanish).
This laptop has as standard an Intel Celeron 2800MHz CPU, 512MB RAM (of which 446MB are available due to video chip RAM sharing), 40GB IDE hard drive, wireless, modem, DVD ROM optical drive, 2 PCMCIA ports, touchpad, multimedia keys, 15" LCD screen, 3 USB ports, S-video and VGA out ports, parallel port, PS/2 port, IR sensor. Chip details from lspci:
00:00.0 Host bridge: ATI Technologies Inc RS200/RS200M AGP Bridge [IGP 340M] (rev 02) 00:01.0 PCI bridge: ATI Technologies Inc PCI Bridge [IGP 340M] 00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 02) 00:07.0 ISA bridge: ALi Corporation M1533/M1535/M1543 PCI to ISA Bridge [Aladdin IV/V/V+] 00:08.0 Modem: ALi Corporation M5457 AC'97 Modem Controller 00:09.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 02) 00:0a.0 CardBus bridge: O2 Micro, Inc. OZ601/6912/711E0 CardBus/SmartCardBus Controller 00:0b.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 50) 00:0b.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 50) 00:0b.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 51) 00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c4) 00:11.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU] 00:12.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon IGP 330M/340M/350M
What Works Without Configuration?
Ethernet, video, audio, microphone, touchpad, USB ports, optical drive, external video port (if booted with video device attached), CPU frequency scaling, screen brightness keys.
What Works With Configuration?
What Does Not Work?
Three of the upper multimedia keys (2nd, 3rd and 4th from left), fn+f12, wireless off switch at front right of laptop, audio mute switch at right front side of laptop.
PCMCIA, Modem, S-Video port, parallel port.
Wireless: The older Broadcom wireless chip in this laptop requires the b43legacy module to function properly. Also, you must specifically follow the instructions on how to install the firmware - this is explained here: Broadcom wireless , in the "b43legacy" section of that wiki entry. The wireless off hardware swith at left front of laptop does not work but you can do almost the equivalent with "sudo iwconfig wlan0 txpower off".
Video: The older ATI IGP 330M video chip in this laptop requires the xf86-video-ati "radeon" open-source driver. Apparently the latest "catalyst" drivers from ATI do not work with this chip, but I have not tested this. The radeon driver, however, works well, but runs a bit hot (see below).
Kernel boot parameters: It might make some difference to your power consumption if you add the following kernel parameters to the "kernel" of your boot config file (for those using grub this is /boot/grub/menu.lst):
Suspend/Hibernate: The "pm-suspend" and "pm-hibernate" scripts from the pm-utils package work well but you need to bind keys to access these scripts because fn+f12 has no scancode.
Function Keys: Only two of the upper keyboard silver multimedia keys have scancodes. For information on how to bind keycodes please read Extra Keyboard Keys.
CPU Temperature: The Lm sensors package utility "sensors-detect" does not find any sensor chips. Instead, read the file:
to get the CPU temperature. Using ArchLinux with kernel 2.6.39 I find that the laptop runs quite hot. It starts at about 32degC and then continues to climb rapidly to 47deg C, with the fan on past 47degC, even at idle, with less than 2% CPU activity. I have attempted many energy saving tools as per Laptop but to little avail. The laptop consumes about 25 watts at idle with the screen on at about mid brightness. I suspect some of the heat may be generated by the video chip as I have heard that the "radeon" module can run the video chip hotter than necessary. I have been unable to get energy saving features of this video chip activated as per https://wiki.archlinux.org/index.php/Ati#With_KMS_enabled . As I have never run any other operating system on this laptop, I would be interested to hear if other owners have success in dropping the power usage and temperature level of this laptop.
This laptop is now older hardware. Out of the box it has only 446MB RAM available. It is suggested you do not install the Gnome or KDE desktop environments as you will then constantly be using your swap partition and you can therefore expect sluggishness. I use the Fluxbox window manager. My ArchLinux system boots from cold button press to a ready desktop in just 35 seconds, including a SLiM graphical login page. It shuts down in about 7 seconds and resumes from suspend in about 2 seconds. Immediately after desktop ready and with one urxvt terminal open it has used just 47MB, excluding buffers and cache! The Opera browser launches from cold within 9 seconds. I have seen very modern laptops running Windows 7 perform much worse than this. Have fun with it, it is still an incredibly usable laptop with the right operating system and window manager installed.
Also, many owners have commented how annoying all those bright blue multimedia key LED lights are as they are located immediately beneath the screen. I have placed black electrical tape over them and then with a razor knife cut around the tape to form the tape to the grill edges. It now looks as if those silly lights were never there and reading the screen is much easier on the eyes!
The leftmost upper multimedia key can be used as an on/off switch and a resume from suspend/hibernate key. This is useful because the default on/off button for this laptop is poorly designed and often fails or requires significant pressure to work properly.
BIOS Flashing Concerns
It is possible that a BIOS upgrade may fix some of the missing key scancodes and missing hardware control function as listed above. But probably not ;-). Nonetheless if you wish to upgrade your BIOS this is how to do it in Linux. The BIOS upgrade download at the HP support website ( http://tinyurl.com/629wd38 ) is a Windows only executable file and is designed to create bootable floppies. This is about as useless as tits on a bull because this laptop has no floppy drive! To get it to flash under Linux you need to:
- Run the Windows BIOS upgrade file as an executable under a MS Windows operating system
- Rather than inserting a floppy use Windows Explorer to navigate to the directory where the extracted image file (rom.img) was stored.
- Copy the rom.img file to a USB thumb drive and then copy that file from the thumb drive into your Linux system
- Using "unetbootin" ( http://unetbootin.sourceforge.net ) create a bootable FreeDOS USB thumb drive with that image file
- Set the BIOS to boot first from a USB device
- Boot your laptop from the USB thumb drive
- The BIOS flashing software (Phoenix Phlash) should start automatically
This procedure should be foolproof yet did not work for me. The Phlash software started up but hangs at reading the .bin file. I suspect that it balks at reading data from USB. Someone needs to test this with an external floppy drive device and see if a BIOS flash upgrade really does work on this laptop. Please let me know if you are successful with either method and I will include further details here.