Difference between revisions of "IPv6 (简体中文)"

From ArchWiki
Jump to: navigation, search
(Page moved.)
Line 1: Line 1:
[[Category:Networking (简体中文)]]
[[Category:Networking (简体中文)]]
[[es:Disabling IPv6]]
[[pt:Disabling IPv6]]

Revision as of 17:40, 29 November 2012

zh-TW:IPv6 Template:Article summary start Template:Article summary text Template:Article summary heading Template:Article summary wiki Template:Article summary end


附注: please use the first argument of the template to provide more detailed indications.
翻译状态: 本文是英文页面 IPv6翻译,最后翻译时间:2012-10-07,点击这里可以查看翻译后英文页面的改动。

在Arch Linux, IPv6默认是打开的。如果你要找IPv6隧道的资料,可以看 IPv6 - Tunnel Broker Setup.

Privacy Extensions

To enable Privacy Extensions for Stateless Address Autoconfiguration in IPv6 according to RFC 4941, reproduce the following steps:

Add these lines to /etc/sysctl.conf:

# Enable IPv6 Privacy Extensions
net.ipv6.conf.all.use_tempaddr = 2
net.ipv6.conf.default.use_tempaddr = 2
net.ipv6.conf.<nic0>.use_tempaddr = 2
net.ipv6.conf.<nicN>.use_tempaddr = 2

Where <nic0> to <nicN> are your nic's (the "all" or "default" parameters do not apply to nic's that already exist when the sysctl settings are applied).

After a reboot, at the latest, Privacy Extensions should be enabled.

Neighbor Discovery

Pinging the multicast address ff02::1 results in all hosts in link-local scope responding. An interface has to be specified. With a ping to the multicast address ff02::2 only routers will respond.

$ ping6 ff02::1%eth0

If you add an option -I <your-global-ipv6>, link-local hosts will respond with their link-global scope addresses. The interface can be omitted in this case.

$ ping6 -I 2001:4f8:fff6::21 ff02::1


Sometime using static address can improve security. For example, if your local router uses Neighbor Discovery or radvd (RFC 2461), your interface will automatically be assigned an address based its MAC address (using IPv6's Stateless Autoconfiguration). This may be less than ideal for security since it allows a system to be tracked even if the network portion of the IP address changes.

To assign a static address (for example 2001:470:1000:1000::5/64):

Add your static IP using netcfg. You can load them at startup by specifying your netcfg profiles in the NETWORKS section of /etc/rc.conf:


DESCRIPTION='ipv6+ipv4 eth0'





Finally DAEMONS section should contain "net-profiles" instead of the deprecated "network". See Netcfg for more information.

禁用 IPv6

禁用 IPv6 据称可以加速网络访问速度,因为在不支持 IPv6 的网络上程序也会试图使用它来访问。另外说一句, Firefox 也在受影响的程序列表中。在 IPv6 广泛采用之前,我们可以通过禁用它受益。


禁用 IPv6

Note: The Arch kernel has IPv6 support built in directly [1], therefore a module cannot be blacklisted.

Disable functionality

Adding ipv6.disable=1 to the kernel line disables the whole IPv6 stack, which is likely what you want if you are experiencing issues. See Kernel parameters for more information.

Alternatively, adding ipv6.disable_ipv6=1 instead will keep the IPv6 stack functional but will not assign IPv6 addresses to any of your network devices.

One can also avoid assigning IPv6 addresses to specific network interfaces by adding the following sysctl config to /etc/sysctl.d/ipv6.conf:

# Disable IPv6
net.ipv6.conf.all.disable_ipv6 = 1
net.ipv6.conf.<interface0>.disable_ipv6 = 1
net.ipv6.conf.<interfaceN>.disable_ipv6 = 1

Note that you must list all of the targeted interfaces explicitly, as disabling "all" does not apply to interfaces that are already "up" when sysctl settings are applied.

Other programs

Disabling IPv6 functionality in the kernel does not prevent other programs from trying to use IPv6. In most cases, this is completely harmless, but if you find yourself having issues with that program, you should consult the program's manpages for a way to disable that functionality.

For instance, dhcpcd will continue to harmlessly attempt to perform IPv6 router solicitation. To disable this, as stated in the dhcpcd.conf manpage, add the following to /etc/dhcpcd.conf:



  • ipv6 - kernel.org 文档库