Difference between revisions of "Idea netsetter (Huawei EG162G)"

From ArchWiki
Jump to: navigation, search
(Configure and dial)
(Configure and dial)
Line 21: Line 21:
  
 
[Dialer Defaults]
 
[Dialer Defaults]
Modem=/dev/ttyUSB1
+
Modem=/dev/ttyUSB1
Baud = 460800
+
Baud = 460800
Init 1 = AT+CGMM
+
Init 1 = AT+CGMM
Init 2 = AT+CMEE=1
+
Init 2 = AT+CMEE=1
Init 3 = ATE0
+
Init 3 = ATE0
Init 4 = AT^HS=0,0
+
Init 4 = AT^HS=0,0
Init 5 = AT+CFUN?
+
Init 5 = AT+CFUN?
Init 6 = AT+CLCK="SC",2
+
Init 6 = AT+CLCK="SC",2
Init 7 = AT+CPIN?
+
Init 7 = AT+CPIN?
Init 8 = AT+CLCK="SC",2
+
Init 8 = AT+CLCK="SC",2
Modem Type = USB MODEM
+
Modem Type = USB MODEM
Phone=*99#
+
Phone=*99#
Username = idea
+
Username = idea
Password = idea
+
Password = idea
Dial Command=ATDT
+
Dial Command=ATDT
Stupid Mode=1
+
Stupid Mode=1
ISDN=0
+
ISDN=0
  
 
{{Note|  
 
{{Note|  
Line 50: Line 50:
  
 
if the connection is successfull you will see something like this:  
 
if the connection is successfull you will see something like this:  
bash-3.2# wvdial
+
bash-3.2# wvdial
--> WvDial: Internet dialer version 1.60
+
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
+
--> Cannot get information for serial port.
--> Initializing modem.
+
--> Initializing modem.
--> Sending: ATZ
+
--> Sending: ATZ
ATZ
+
ATZ
OK
+
OK
--> Modem initialized.
+
--> Modem initialized.
--> Sending: ATDT*99#
+
--> Sending: ATDT*99#
--> Waiting for carrier.
+
--> Waiting for carrier.
ATDT*99#
+
ATDT*99#
CONNECT
+
CONNECT
--> Carrier detected.  Starting PPP immediately.
+
--> Carrier detected.  Starting PPP immediately.
--> Starting pppd at Sun May 24 02:03:51 2009
+
--> Starting pppd at Sun May 24 02:03:51 2009
--> Pid of pppd: 6361
+
--> Pid of pppd: 6361
--> Using interface ppp0
+
--> Using interface ppp0
--> pppd: è|[01]¸8A[08]È@Þ[08]
+
--> pppd: è|[01]¸8A[08]È@Þ[08]
--> pppd: è|[01]޸8A[08]È@Þ[08]
+
--> pppd: è|[01]޸8A[08]È@Þ[08]
--> pppd: è|[01]޸8AÞ[08]È@Þ[08]
+
--> pppd: è|[01]޸8AÞ[08]È@Þ[08]
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
+
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
+
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
+
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
--> local  IP address 112.110.117.241
+
--> local  IP address 112.110.117.241
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
+
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
--> remote IP address 10.64.64.64
+
--> remote IP address 10.64.64.64
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
+
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
--> primary  DNS address 10.11.12.13
+
--> primary  DNS address 10.11.12.13
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
+
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
--> secondary DNS address 10.11.12.14
+
--> secondary DNS address 10.11.12.14
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
+
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]  
 +
 
 +
 
 +
{{Note| if you get an error 16 in wvdial it means that there is no modem present in the port specified by the config, so edit your config file accordingly}}
 +
 
  
 
but you still wont be able to surf the net unless you have a nameserver in ur resolv.conf. if you dont have a nameserver in your resolv.conf
 
but you still wont be able to surf the net unless you have a nameserver in ur resolv.conf. if you dont have a nameserver in your resolv.conf

Revision as of 20:42, 23 May 2009


Introduction

The HUAWEI EG162G is a EDGE/GPRS modem used for wireless internet access. The current kernel (2.6.29.4) has support for this device and thus setting this up isnt very hard

Plug it in

Plug in the device , wait for a few seconds and then run

$ ls /dev/ttyUSB*

you will see something like this: /dev/ttyUSB1 /dev/ttyUSB2 /dev/ttyUSB3 the first one is the port of the modem.

Installation

Now install wvdial which is a dialer

# pacman -Sy wvdial

or if you dont have ppp install that too

# pacman -Sy wvdial ppp

Configure and dial

Edit your /etc/wvdial.conf and use this if you are using an idea netsetter , else use google to find the right config for your provider

[Dialer Defaults]

Modem=/dev/ttyUSB1
Baud = 460800
Init 1 = AT+CGMM
Init 2 = AT+CMEE=1
Init 3 = ATE0
Init 4 = AT^HS=0,0
Init 5 = AT+CFUN?
Init 6 = AT+CLCK="SC",2
Init 7 = AT+CPIN?
Init 8 = AT+CLCK="SC",2
Modem Type = USB MODEM
Phone=*99#
Username = idea
Password = idea
Dial Command=ATDT
Stupid Mode=1
ISDN=0
Note:
Template error: are you trying to use the = sign? Visit Help:Template#Escape template-breaking characters for workarounds.


now all you need to do is run wvdial as root

# wvdial

if you get an error 16 in wvdial it means that there is no modem present in the port specified by the config, so edit your config file accordingly

if the connection is successfull you will see something like this:

bash-3.2# wvdial
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Modem initialized.
--> Sending: ATDT*99#
--> Waiting for carrier.
ATDT*99#
CONNECT
--> Carrier detected.  Starting PPP immediately.
--> Starting pppd at Sun May 24 02:03:51 2009
--> Pid of pppd: 6361
--> Using interface ppp0
--> pppd: è|[01]¸8A[08]È@Þ[08]
--> pppd: è|[01]޸8A[08]È@Þ[08]
--> pppd: è|[01]޸8AÞ[08]È@Þ[08]
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
--> local  IP address 112.110.117.241
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
--> remote IP address 10.64.64.64
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
--> primary   DNS address 10.11.12.13
--> pppd: è|[01]¸8AÞ[08]È@Þ[08]
--> secondary DNS address 10.11.12.14
--> pppd: è|[01]¸8AÞ[08]È@Þ[08] 


Note: if you get an error 16 in wvdial it means that there is no modem present in the port specified by the config, so edit your config file accordingly


but you still wont be able to surf the net unless you have a nameserver in ur resolv.conf. if you dont have a nameserver in your resolv.conf then edit /etc/resolv.conf and add this line to it nameserver 208.67.222.222

If you are already conected to a lan then change the subnet mask of the lan to 255.0.0.0 and you should be able to use the lan and the netsetter