Difference between revisions of "Install Arch Linux on a USB key"

From ArchWiki
Jump to navigation Jump to search
(use https for links to archlinux.org)
Line 1: Line 1:
[[Category:Getting and installing Arch]]
[[Category:Getting and installing Arch]]
[[es:Installing Arch Linux on a USB key]]
[[it:Installing Arch Linux on a USB key]]
[[it:Installing Arch Linux on a USB key]]
[[zh-CN:Installing Arch Linux on a USB key]]
[[zh-CN:Installing Arch Linux on a USB key]]

Revision as of 10:52, 11 December 2012

zh-CN:Installing Arch Linux on a USB key

Tango-view-refresh-red.pngThis article or section is out of date.Tango-view-refresh-red.png

Reason: Should be updated to reflect changes in provided bootloaders and installation instructions. (Discuss in Talk:Install Arch Linux on a USB key#)

This page discusses how to perform a regular Arch installation onto a USB key (or "flash drive"). The result will be a system that will be updated through normal use. Consider whether you're instead interested in USB Installation Media.

Grab a big enough USB key

If installing KDE and a large amount of applications, 3 GiB is the recommended minimum. GNOME and Xfce4, along with a typical set of packages for a desktop (GIMP, Pidgin, OpenOffice, Firefox, flashplugin) can be installed on a 2 GiB stick, leaving a small amount of room for user data.

Install from...

  • An Arch Linux CD can be used to install Arch onto the USB key, via booting the CD and following the Installation Guide.
  • Or, if you have another linux computer available (it need not be Arch), you can follow the instructions to install from existing linux, and then skip to the configuration section.
  • In case you are already running Arch, simply install arch-install-scripts and then install just like you would from the iso, but you will not be using /dev/sda, most likely it will be /dev/sdb. (Be very careful. You don't want to go about deleting everyting on your hard drive)


Follow the Installation Guide as you normally would, with these exceptions:

  • If cfdisk fails with "Partition ends in the final partial cylinder" fatal error, the only way to proceed is to kill all partitions on the drive. Open another terminal (Template:Keypress), type fdisk /dev/sdX (where sdX is your usb drive), print partition table (p), check that it's ok, delete it (d) and write changes (w). Now return to cfdisk.
  • It is highly recommended to review the Tips for Minimizing SSD Read/Writes on the SSD wiki article prior to selecting a filesystem. To sum up, ext4 with a journal should be fine. Recognize that flash has a limited number of writes, and a journaling file system will take some of these as the journal is updated. For this same reason, it is best to forgo a swap partition. Note that this does not affect installing onto a USB hard drive.
  • Before creating the initial RAM disk # mkinitcpio -p linux, in /etc/mkinitcpio.conf add the usb hook to the hooks array right after udev. This is necessary for appropriate module loading in early userspace.


  • Make sure that /etc/fstab includes the correct partition information for /, and for any other partitions on the USB key. If the usb key is to be booted on several machines, it is quite likely that devices and number of available hard disks vary. So it is advised to use UUID or label:

To get the proper UUIDs for your partitions issue blkid

  • menu.lst, the Grub configuration file, should be edited to (loosely) match the following:
Note: When grub is installed on the USB key, the key will always be hd0,0
Note: It seems that current versions of GRUB2 will automatically default to using uuid. The following directions are for GRUB legacy

With the static /dev/sdaX:

root (hd0,0)
kernel /boot/vmlinuz-linux root=/dev/sda1 ro
initrd /boot/initramfs-linux.img

When using label your menu.lst should look like this:

root (hd0,0)
kernel /boot/vmlinuz-linux root=/dev/disk/by-label/Arch ro
initrd /boot/initramfs-linux.img

And for UUID, it should be like this:

root (hd0,0)
kernel /boot/vmlinuz-linux root=/dev/disk/by-uuid/3a9f8929-627b-4667-9db4-388c4eaaf9fa ro
initrd /boot/initramfs-linux.img


Painless boot on different machines without using UUID

When using the USB key on various target machines, it is helpful to have multiple entries in GRUB, for machines with different setups. For example, the GRUB configuration could contain:

# (0) Arch Linux
title  Arch Linux (first drive)
root   (hd0,0)
kernel /boot/vmlinuz-linux root=/dev/sda1 ro
initrd /boot/initramfs-linux.img

As well as

# (1) Arch Linux
title  Arch Linux (second drive)
root   (hd0,0)
kernel /boot/vmlinuz-linux root=/dev/sdb1 ro
initrd /boot/initramfs-linux.img

And so forth, giving you the option to select a configuration for a wider variety of machines. However, changing the root= option in GRUB does not change /etc/fstab and you must do something (in our example using udev symlink), so the root partition will always be mounted correctly.

  • Run udevinfo -p /sys/block/sdx/ -a (where sdx is the device name of your usb key)
  • Find unique information pertaining to your usb key. I chose SYSFS{model}=="DataTraveler 2.0"
  • Make a new file: /etc/udev/udev.rules/10-my-usb-key.rules and insert:
KERNEL=="sd**", SYSFS{product}=="DataTraveler 2.0", SYMLINK+="WHATEVERYOUWANTOTCALLIT%n"
(KERNEL=="sd**" is because the kernel - 2.6.16 here - names all usb devices sd as it uses the scsi sub-system and you want to look at every sd device and apply the setting to every partition), with SYSFS{model}== being the unique identifier collected from udevinfo.
  • Run /etc/start-udev uevents and make sure the symlinks appears in /dev.
  • If so, edit /etc/fstab, replacing your old sdx with the new symlinks.

Optimizing for the lifespan of flash memory

See Also