Since Intel provides and supports open source drivers, Intel graphics are essentially plug-and-play.
For a comprehensive list of Intel GPU models and corresponding chipsets and CPUs, see this comparison on Wikipedia.
- 1 Installation
- 2 Loading
- 3 Xorg configuration
- 4 Module-based Powersaving Options
- 5 Tips and tricks
- 6 Troubleshooting
- 6.1 SNA issues
- 6.2 DRI3 issues
- 6.3 Font and screen corruption in GTK+ applications (missing glyphs after suspend/resume)
- 6.4 Blank screen during boot, when "Loading modules"
- 6.5 X freeze/crash with intel driver
- 6.6 Baytrail complete freeze
- 6.7 Adding undetected resolutions
- 6.8 Weathered colors (color range problem)
- 6.9 Backlight is not adjustable
- 6.10 Corruption/Unresponsiveness in Chromium and Firefox
- 6.11 Kernel crashing w/kernels 4.0+ on Broadwell/Core-M chips
- 6.12 Lag in Windows guests
- 6.13 Screen flickering
- 6.14 OpenGL 2.1 with i915 driver
- 7 See also
Install the package, which provides the DRI driver for 3D acceleration.
- For 32-bit application support, also install the multilib repository. package from the
- For the DDX driver (which provides 2D acceleration in Xorg), install the package. (Often not recommended, see note below.)
- For Vulkan support (Ivy Bridge and newer), install the package.
Also see Hardware video acceleration.
The Intel kernel module should load fine automatically on system boot.
If it does not happen, then:
- Make sure you do not have
vga=as a kernel parameter, since Intel requires kernel mode-setting.
- Also, check that you have not disabled Intel by using any modprobe blacklisting within
Enable early KMS
Kernel mode setting (KMS) is supported by Intel chipsets that use the i915 DRM driver and is mandatory and enabled by default.
Refer to Kernel mode setting#Early KMS start for instructions on how to enable KMS as soon as possible at the boot process.
Enable GuC / HuC firmware loading
For Skylake and newer processors, some video features (e.g. CBR rate control on SKL low-power encoding mode) may require the use of an updated GPU firmware, which is currently (as of 4.14) not enabled by default.
It is necessary to add
i915.enable_guc_loading=1 i915.enable_guc_submission=1 to the kernel parameters to enable it. Alternatively, if the initramfs already includes the i915 module (see Kernel mode setting#Early KMS start), you can set these options through a file in
options i915 enable_guc_loading=1 enable_guc_submission=1
For kernel 4.16 and latest:
options i915 enable_guc=1
Update in 4.16 kernel: parm: enable_guc:Enable GuC load for GuC submission and/or HuC load. Required functionality can be selected using bitmask values. (-1=auto, 0=disable [default], 1=GuC submission, 2=HuC load) (int)
You can verify that it is enabled by checking dmesg:
[ 2.142029] [drm] GuC loaded (firmware i915/skl_guc_ver6_1.bin [version 6.1])
# cat /sys/kernel/debug/dri/0/i915_huc_load_status # cat /sys/kernel/debug/dri/0/i915_guc_load_status
There is no need for any configuration to run Xorg.
However, to take advantage of some driver options, you will need to create a Xorg configuration file similar to the one below:
Section "Device" Identifier "Intel Graphics" Driver "intel" EndSection
Additional options are added by the user on new lines below
For the full list of options, see the man page.
- You may need to indicate
Option "AccelMethod"when creating a configuration file, even just to set it to the default method (currently
"sna"); otherwise, X may crash.
- You might need to add more device sections than the one listed above. This will be indicated where necessary.
Module-based Powersaving Options
i915 kernel module allows for configuration via module options. Some of the module options impact power saving.
A list of all options along with short descriptions and default values can be generated with the following command:
$ modinfo -p i915
To check which options are currently enabled, run
# systool -m i915 -av
You will note that many options default to -1, resulting in per-chip powersaving defaults. It is however possible to configure more aggressive powersaving by using module options.
The following option should be generally safe to enable:
options i915 enable_fbc=1
Framebuffer compression (enable_fbc)
Framebuffer compression may be unreliable or unavailable on Intel GPU generations before Sandy Bridge (generation 6). This results in messages logged to the system journal similar to this one:
kernel: drm: not enough stolen space for compressed buffer, disabling.
Enabling frame buffer compression on pre-Sandy Bridge CPUs results in endless error messages:
$ dmesg |tail [ 2360.475430] [drm] not enough stolen space for compressed buffer (need 4325376 bytes), disabling [ 2360.475437] [drm] hint: you may be able to increase stolen memory size in the BIOS to avoid this
The solution is to disable frame buffer compression which will imperceptibly increase power consumption (around 0.06 W). In order to disable it add
i915.enable_fbc=0 to the kernel line parameters. More information on the results of disabled compression can be found here.
Tips and tricks
The SNA acceleration method causes tearing for some people. To fix this, enable the
"TearFree" option in the driver by adding the following line to your configuration file:
Option "TearFree" "true"
See the original bug report for more info.
- This option may not work when
- This option may increases memory allocation considerably and reduce performance. 
- This option is problematic for applications that are very picky about vsync timing, like Super Meat Boy.
- This option does not work with UXA acceleration method, only with SNA.
Disable Vertical Synchronization (VSYNC)
- Chomium/Chrome has lags and slow performance due to GPU and runs smoothly with --disable-gpu switch
- glxgears test does not show desired performance
The intel-driver uses Triple Buffering for vertical synchronization, this allows for full performance and avoids tearing. To turn vertical synchronization off (e.g. for benchmarking) use this
.drirc in your home directory:
<device screen="0" driver="dri2"> <application name="Default"> <option name="vblank_mode" value="0"/> </application> </device>
Setting scaling mode
This can be useful for some full screen applications:
$ xrandr --output LVDS1 --set PANEL_FITTING param
param can be:
center: resolution will be kept exactly as defined, no scaling will be made,
full: scale the resolution so it uses the entire screen or
full_aspect: scale the resolution to the maximum possible but keep the aspect ratio.
If it does not work, try:
$ xrandr --output LVDS1 --set "scaling mode" param
param is one of
KMS Issue: console is limited to small area
One of the low-resolution video ports may be enabled on boot which is causing the terminal to utilize a small area of the screen. To fix, explicitly disable the port with an i915 module setting with
video=SVIDEO-1:d in the kernel command line parameter in the bootloader. See Kernel parameters for more info.
If that does not work, try disabling TV1 or VGA1 instead of SVIDEO-1. Video port names can be listed with xrandr.
Hardware accelerated H.264 decoding on GMA 4500
The . This is echoed by other experiences . Setting the preallocated video ram size higher in bios results in much better hardware decoded playback. Even 1080p h264 works well if this is done. Smooth playback (1080p/720p) works also with AUR in combination with AUR and AUR. With MPV and the Firefox plugin "Watch with MPV" it is possible to watch hardware accelerated YouTube videos.package only provides hardware accelerated MPEG-2 decoding for GMA 4500 series GPUs. The H.264 decoding support is maintained in a separated g45-h264 branch, which can be used by installing AUR package. Note however that this support is experimental and its development has been abandoned. Using the VA-API with this driver on a GMA 4500 series GPU will offload the CPU but may not result in as smooth a playback as non-accelerated playback. Tests using mplayer showed that using vaapi to play back an H.264 encoded 1080p video halved the CPU load (compared to the XV overlay) but resulted in very choppy playback, while 720p worked reasonably well
Setting brightness and gamma
SNA is the default acceleration method in configuration file:. If you experience issues with SNA (e.g. pixelated graphics, corrupt text, etc.), try using UXA instead, which can be done by adding the following line to your
Option "AccelMethod" "uxa"
Option "DRI" "2"
modesetting driver, this method of disabling DRI3 does not work. Instead, one can set the environment variable
Font and screen corruption in GTK+ applications (missing glyphs after suspend/resume)
Should you experience missing font glyphs in GTK+ applications, the following workaround might help. Edit
/etc/environment to add the following line:
See also FreeDesktop bug 88584.
Blank screen during boot, when "Loading modules"
If using "late start" KMS and the screen goes blank when "Loading modules", it may help to add
intel_agp to the initramfs. See Kernel mode setting#Early KMS start section.
Alternatively, appending the following kernel parameter seems to work as well:
If you need to output to VGA then try this:
X freeze/crash with intel driver
Some issues with X crashing, GPU hanging, or problems with X freezing, can be fixed by disabling the GPU usage with the
NoAccel option - add the following lines to your configuration file:
Option "NoAccel" "True"
Alternatively, try to disable the 3D acceleration only with the
Option "DRI" "False"
If you experience crashes and have
Option "TearFree" "true" Option "AccelMethod" "sna"
in your configuration file, in most cases these can be fixed by adding
to your boot parameters.
Baytrail complete freeze
If you are using kernel > 3.16 on Baytrail architecture and randomly encounter total system freezes, the following kernel option is a workaround until this bug is fixed in the linux kernel.
This is originally an Intel CPU bug that can be triggered by certain c-state transitions. It can also happen with Linux kernel 3.16 or Windows, though apparently much more rarely. The kernel option will prevent the freeze by avoiding c-state transitions but will also increase power consumption.
Adding undetected resolutions
This issue is covered on the Xrandr page.
Weathered colors (color range problem)
Kernel 3.9 contains a new default "Automatic" mode for the "Broadcast RGB" property in the Intel driver. It is almost equivalent to "Limited 16:235" (instead of the old default "Full") whenever an HDMI/DP output is in a CEA mode. If a monitor does not support signal in limited color range, it will cause weathered colors.
One can force mode e.g.
xrandr --output <HDMI> --set "Broadcast RGB" "Full" (replace
<HDMI> with the appropriate output device, verify by running
Unfortunately, the Intel driver does not support setting the color range through an
xorg.conf.d configuration file.
A bug report is filed and a patch can be found in the attachment.
Backlight is not adjustable
If after resuming from suspend, the hotkeys for changing the screen brightness do not take effect, check your configuration against the Backlight article.
If the problem persists, try one of the following kernel parameters:
acpi_osi=Linux acpi_osi="!Windows 2012" acpi_osi=
Corruption/Unresponsiveness in Chromium and Firefox
If you experience corruption, unresponsiveness, lags or slow performance in Chromium and/or Firefox:
Kernel crashing w/kernels 4.0+ on Broadwell/Core-M chips
A few seconds after X/Wayland loads the machine will freeze and journalctl will log a kernel crash referencing the Intel graphics as below:
Jun 16 17:54:03 hostname kernel: BUG: unable to handle kernel NULL pointer dereference at (null) Jun 16 17:54:03 hostname kernel: IP: [< (null)>] (null) ... Jun 16 17:54:03 hostname kernel: CPU: 0 PID: 733 Comm: gnome-shell Tainted: G U O 4.0.5-1-ARCH #1 ... Jun 16 17:54:03 hostname kernel: Call Trace: Jun 16 17:54:03 hostname kernel: [<ffffffffa055cc27>] ? i915_gem_object_sync+0xe7/0x190 [i915] Jun 16 17:54:03 hostname kernel: [<ffffffffa0579634>] intel_execlists_submission+0x294/0x4c0 [i915] Jun 16 17:54:03 hostname kernel: [<ffffffffa05539fc>] i915_gem_do_execbuffer.isra.12+0xabc/0x1230 [i915] Jun 16 17:54:03 hostname kernel: [<ffffffffa055d349>] ? i915_gem_object_set_to_cpu_domain+0xa9/0x1f0 [i915] Jun 16 17:54:03 hostname kernel: [<ffffffff811ba2ae>] ? __kmalloc+0x2e/0x2a0 Jun 16 17:54:03 hostname kernel: [<ffffffffa0555471>] i915_gem_execbuffer2+0x141/0x2b0 [i915] Jun 16 17:54:03 hostname kernel: [<ffffffffa042fcab>] drm_ioctl+0x1db/0x640 [drm] Jun 16 17:54:03 hostname kernel: [<ffffffffa0555330>] ? i915_gem_execbuffer+0x450/0x450 [i915] Jun 16 17:54:03 hostname kernel: [<ffffffff8122339b>] ? eventfd_ctx_read+0x16b/0x200 Jun 16 17:54:03 hostname kernel: [<ffffffff811ebc36>] do_vfs_ioctl+0x2c6/0x4d0 Jun 16 17:54:03 hostname kernel: [<ffffffff811f6452>] ? __fget+0x72/0xb0 Jun 16 17:54:03 hostname kernel: [<ffffffff811ebec1>] SyS_ioctl+0x81/0xa0 Jun 16 17:54:03 hostname kernel: [<ffffffff8157a589>] system_call_fastpath+0x12/0x17 Jun 16 17:54:03 hostname kernel: Code: Bad RIP value. Jun 16 17:54:03 hostname kernel: RIP [< (null)>] (null)
This can be fixed by disabling execlist support which was changed to default on with kernel 4.0. Add the following kernel parameter:
This is known to be broken to at least kernel 4.0.5.
Lag in Windows guests
The video output of a Windows guest in VirtualBox sometimes hangs until the host forces a screen update (e.g. by moving the mouse cursor). Removing the
enable_fbc=1 option fixes this issue.
The following power saving features used by intel iGPUs are known to cause flickering in some instances. A temporary solution is to disable one of them using the appropriate kernel boot parameter option:
- Rc6 sleep modes (see #RC6 sleep modes (enable_rc6)), can be disabled with
- Panel Self Refresh (PSR) FS#49628 FS#49371 FS#50605. To disable this feature use the option
OpenGL 2.1 with i915 driver
<driconf> ... <device driver="i915"> <application name="Default"> <option name="stub_occlusion_query" value="true" /> <option name="fragment_shader" value="true" /> </application> </device> ... </driconf>
- https://01.org/linuxgraphics/documentation (includes a list of supported hardware)