LIRC Device Examples

From ArchWiki
Revision as of 12:31, 8 December 2013 by Graysky (talk | contribs) (removed outdated and poorly written section and general cleanup)
Jump to: navigation, search

Template:Article summary start Template:Article summary text Template:Article summary heading Template:Article summary wiki - Main LIRC article. Template:Article summary end

Asus DH Deluxe series motherboard

Check the output of:

$ cat /dev/usb/hiddevX

where X is 0,1 or bigger, and press some buttons on remote. If characters result, then the device is working, follow steps:

1. In file /etc/conf.d/lircd.conf add:


2. Reload LIRC:

# systemctl restart lirc

ASRock ION series (Nuvoton) quickstart

$ ln -s /usr/share/lirc/remotes/lirc_wb677/lircd.conf.wb677 /etc/lirc/lircd.conf
# systemctl restart lirc

Serial Port "Home Brew" IR Receiver

1. Create a udev rule to give non-privleged users read/write access to the serial port. In this example, ttyS0 is used.

# For serial port ttyS0 and LIRC

2. Create the needed modprobe configs

install lirc_serial /usr/bin/setserial /dev/ttyS0 uart none && /sbin/modprobe --first-time --ignore-install lirc_serial
options lirc_serial type=0
remove lirc_serial /sbin/modprobe -r --first-time --ignore-remove lirc_serial && /sbin/modprobe -r lirc_dev
Note: Using udev rules to run the setserial command does not work in my experience because lirc_serial gets loaded before the serial port rules are applied.

3. Install a custom systemd service file.

Description=Linux Infrared Remote Control

ExecStartPre=/bin/rm -f /dev/lirc /dev/lircd /var/run/lirc/lircd
ExecStart=/usr/sbin/lircd -n -r -P /run/lirc/ -d /dev/lirc0 -o /run/lirc/lircd
ExecStartPost=/usr/bin/ln -sf /run/lirc/lircd /dev/lircd
ExecStartPost=/usr/bin/ln -sf /dev/lirc0 /dev/lirc
ExecReload=/bin/kill -SIGHUP $MAINPID


4. We still need the default tmpfiles to be created, so copy that config file to /etc/tmpfiles.d/lirc.conf.

# cp -a /usr/lib/tmpfiles.d/lirc.conf /etc/tmpfiles.d/lirc.conf

5. Create a ~/.lircrc or a /etc/lirc/lircrc file for system wide use.

6. Have the service start at boot and then test with a reboot

# systemctl enable lirc.service
# systemctl reboot

or load the module and start the lirc.service.

# modprobe lirc_serial
# systemctl start lirc.service

Streamzap PC Remote (USB)

This particular remote is known to not function with the lirc-utils package included lirc.service. Flyspray #37958 has been created. Until it is acted upon, users can create a custom service file that does work:

Description=LIRC Daemon

ExecStartPre=/bin/mkdir -p /run/lirc
ExecStartPre=/bin/rm -f /dev/lircd
ExecStartPre=/bin/rm -f /run/lirc/lircd
ExecStartPre=/bin/ln -s /run/lirc/lircd /dev/lircd
ExecStart=/usr/bin/lircd -d /dev/lirc0 -P /run/lirc/
ExecStopPost=/bin/rm -f /dev/lircd
ExecStopPost=/bin/rm -fR /run/lirc

Note: When the batteries in this remote are low, it may stop working even though the red LED on the received still flashes upon receiving signals!


There is a dedicated wiki page with information about X10