From ArchWiki
Revision as of 23:38, 11 July 2007 by Mr.Elendig (talk | contribs) (Added link to RAID_Encryption_LVM)
Jump to: navigation, search

Tango-document-new.pngThis article is a stub.Tango-document-new.png

Notes: please use the first argument of the template to provide more detailed indications. (Discuss in Talk:LVM2#)

Logical Volume Manager v.2

This is going to be a page dedicated to LVM2, with information on "what, why and how", complete with several examples. What is LVM2, Why use LVM2, How to use LVM2
Anyone and everyone with knowledge and experinece with LVM2 are more than welcome to contribute.
Since this page is far from complete, you shoud also take a look at Installing_with_Software_RAID_or_LVM, TLDP LVM HOWTO and RAID_Encryption_LVM

Example 1: Install with root on lvm2


A desktop system with one disc, 20GB. No other os installed.
The install medium used in this example is the Archlinux-i686-2007.05-Duke-Linuxtag2007.ftp.iso


We need to create some partions. One for /boot and one for the LVM setup. I prefer cfdisk for this, but you can use any tool you like.

/dev/sda1 100Mb Primary, type 83, bootable 
This is going to be boot partion. It is posible to have the boot partion on lvm2, but you will have to use Lilo or Grub 1.95 or later. (arch provides grub 0.97 on the cd)
/dev/sda2 20Gb Primary, type 83 
This is where we are going to put the LVM. You don't realy need to create a partion for it, but it has some advantages. Mainly, many partion tools can't see a LVM setup, and just thinks that the space is free, unless you set up a normal partion for it. This can can cause e.g. if you later decide to set up dualboot with another os.

Set up LVM2

First load the necessary kernel module:

# modprobe md-mod

Initialize the partion so that lvm can use it: Note: On the install cd, you have to run lvm [some_tool] instead of [some_tool] as you woud on an already installed system.

# lvm pvcreate /dev/sda2

Create a volume group (you can use another name instead of vgroup1, if you want)

# lvm vgcreate vgroup1 /dev/sda2

Create some logical volumes(partions) on the volume group. (you can give them any name you want)

  • First, lets create a 5GB / partion:
# lvm lvcreate -L 5G vgroup1 -n root
  • Next, a 512MB swap
# lvm lvcreate -L 512M vgroup1 -n swap
  • And last, let's use the remaining free space for /home
# lvm lvcreate -l 100%FREE vgroup1 -n home

Now we need to activate the volume group before we start the installer:

# lvm vgchange -a y vgroup1

The Arch Installer

Note: This only list the steps that have to do with lvm2. Refer to the install guide for more information about the other steps of the install.
Start the installer

# /arch/setup

In the installer, under "Prepare Hard Drive, skip directly to step 3 "Set Filesystem Mountpoints"(don't choose autoprepare or partion hard drive)

/boot with ext3
/root with ext3
swap with swap
/home with ext3

"Configure System"
Important:' Answer YES to Preconfiguration with hwdetect, and to boot from LVM2

Chang USELVM="no" to USELVM="yes"
Make sure that lvm2 is present in HOOKS=
Just glance over it to check that the mount points are correct.

"Install Bootloader"

The installer usualy get this one right, but just check that everything is ok, specialy the root= line.

Install grub to /dev/sda and choose NO to the software raid question.

That's it, exit the installer, remove the cd, and reboot.