Difference between revisions of "LXD"
(Add Linux Containers to related pages) |
(Move lxc-checkconfig to troubleshooting (default Arch kernel works correctly as of 4.15).) |
||
Line 10: | Line 10: | ||
=== Required software === | === Required software === | ||
Install [[LXC]] and the {{AUR|lxd}} package, then [[start]] {{ic|lxd.service}}. | Install [[LXC]] and the {{AUR|lxd}} package, then [[start]] {{ic|lxd.service}}. | ||
− | |||
− | |||
− | |||
See [[Linux Containers#Enable support to run unprivileged containers (optional)]] if you want to run ''unprivileged'' containers. Otherwise see [[#Launching container without CONFIG_USER_NS]]. | See [[Linux Containers#Enable support to run unprivileged containers (optional)]] if you want to run ''unprivileged'' containers. Otherwise see [[#Launching container without CONFIG_USER_NS]]. | ||
Line 103: | Line 100: | ||
== Troubleshooting == | == Troubleshooting == | ||
+ | === Check kernel config === | ||
+ | Verify that the running kernel is properly configured to run a container: | ||
+ | $ lxc-checkconfig | ||
=== Launching container without CONFIG_USER_NS === | === Launching container without CONFIG_USER_NS === | ||
For launching images you must provide {{ic|1=security.privileged=true}} during image creation: | For launching images you must provide {{ic|1=security.privileged=true}} during image creation: |
Revision as of 19:37, 9 February 2018
LXD is a container "hypervisor" and a new user experience for Linux Containers.
Setup
Required software
Install LXC and the lxdAUR package, then start lxd.service
.
See Linux Containers#Enable support to run unprivileged containers (optional) if you want to run unprivileged containers. Otherwise see #Launching container without CONFIG_USER_NS.
Alternative installation method
An alternative method of installation is via snapd, by installing the snapdAUR package and running:
$ sudo snap install lxd $ sudo lxd init $ sudo usermod -a -G lxd $USER
To test the installation, run:
$ lxc launch ubuntu:16.04 $ lxc list
Accessing LXD as a unprivileged user
By default the LXD daemon allows users in the lxd
group access, so add your user to the group:
# usermod -a -G lxd <user>
LXD Networking
LXD uses LXC's networking capabilities. By default it connects containers to the lxcbr0
network device. Refer to the LXC documentation on network configuration to set up a bridge for your containers.
If you want to use a different interface than lxcbr0
edit the default using the lxc command line tool:
$ lxc profile edit default
An editor will open with a config file that by default contains:
name: default config: {} devices: eth0: name: eth0 nictype: bridged parent: lxcbr0 type: nic
You can set the parent
parameter to whichever bridge you want LXD to attach the containers to by default.
Example network configuration
Thanks to @jpic, the LXD package now provides some example networking configuration in /usr/share/lxd/
. To use this configuration run the following commands:
$ ln -s /usr/share/lxd/dnsmasq-lxd.conf /etc/dnsmasq-lxd.conf $ ln -s /usr/share/lxd/systemd/system/dnsmasq@lxd.service /etc/systemd/system/dnsmasq@lxd.service $ ln -s /usr/share/lxd/netctl/lxd /etc/netctl/lxd $ ln -s /usr/share/lxd/dbus-1/system.d/dnsmasq-lxd.conf /etc/dbus-1/system.d/dnsmasq-lxd.conf
If you use NetworkManager, also symlink the following file:
$ ln -s /usr/share/lxd/NetworkManager/dnsmasq.d/lxd.conf /etc/NetworkManager/dnsmasq.d/lxd.conf
Change parent: lxcbr0
to parent: lxd
:
$ lxc profile edit default
Finally, enable and start dnsmasq@lxd.service
and netctl@lxd.service
.
If you encounter issue with the provided example configuration, or have suggestions to improve it, please leave a comment on the lxdAUR page.
Basic usage
First steps
LXD has two parts, the daemon (the lxd binary), and the client (the lxc binary). Now that the daemon is all configured and running, you can create a container:
$ lxc launch ubuntu:14.04
Alternatively, you can also use a remote LXD host as a source of images. One comes pre-configured in LXD, called "images" (images.linuxcontainers.org)
$ lxc launch images:centos/7/amd64 centos
Advance usage
Modify processes and files limit
You may want to increase file descriptor limit or max user processes limit, since default file descriptor limit is 1024 on Arch Linux.
Edit the lxd.service
:
# systemctl edit lxd.service
[Service] LimitNOFILE=infinity LimitNPROC=infinity TasksMax=infinity
Troubleshooting
Check kernel config
Verify that the running kernel is properly configured to run a container:
$ lxc-checkconfig
Launching container without CONFIG_USER_NS
For launching images you must provide security.privileged=true
during image creation:
$ lxc launch ubuntu:16.04 ubuntu -c security.privileged=true
Or for already existed image you may edit config:
$ lxc config edit ubuntu
name: ubuntu profiles: - default config: ... security.privileged: "true" ... devices: root: path: / type: disk ephemeral: false
Or to enable security.privileged=true
for new containers, edit the config for the default profile:
$ lxc profile edit default
No ipv4 on unprivileged Arch container
This was tested and validated on LXD v.2.20. The container can not start the systemd-networkd
service so does not get a valid ipv4 address. A work-around was suggested by Stéphane Graber (Github Issue), execute on the host and restart the container:
$ lxc profile set default security.syscalls.blacklist "keyctl errno 38"
- stgraber: "The reason is that the networkd systemd unit somehow makes use of the kernel keyring, which doesn't work inside unprivileged containers right now. The line above makes that system call return not-implemented which is enough of a workaround to get things going again."