Lenovo ThinkPad Helix
Lenovo ThinkPad Helix, 3rd Generation Core i5/i7 This model comes without optical drive,. Has UEFI BIOS with BIOS-legacy fallback mode. Has Windows 8 pre-installed.
Due to the fact that there is no optical drive, you need to install Arch from USB stick.
This procedure is far less involved then UEFI and works perfectly.
In order to turn off UEFI booting you will need to boot into your BIOS and change the boot mode to Legacy. Afterward, follow the Beginner's Guide for standard installation instructions.
Installation from UEFI bootable USB works with the default bootloader, so rEFInd is unnecessary. In the BIOS under Startup, set "UEFI/Legacy Boot" to UEFI only. The default partition table (and Windows installation) uses MBR. For UEFI, reformat the disk as GPT.
Booting using an efibootmgr entry works well. The warnings about incompatibility and embedding arguments to do not apply.
Almost everything works out of the box except for the wacom screen due to the digitizer; the helix uses the Atmel Atmel maXTouch Digitizer. although this isn't a wacom digitizer it does work with the wacom drivers, you just have to tell it to.
Make sure to install
Make sure you check that the screen does in fact use the Atmel digitizer with
lsusb then update the xorg configuration:
Section "InputClass" Identifier "Wacom class" MatchProduct "Wacom|WACOM|Hanwang|PTK-540WL|Atmel" MatchDevicePath "/dev/input/event*" Driver "wacom" EndSection Section "InputClass" Identifier "Wacom serial class" MatchProduct "Serial Wacom Tablet" Driver "wacom" EndSection Section "InputClass" Identifier "Wacom serial class identifiers" MatchProduct "WACf|FUJ02e5|FUJ02e7|FUJ02e9" Driver "wacom" EndSection # Waltop tablets Section "InputClass" Identifier "Waltop class" MatchProduct "WALTOP" MatchIsTablet "on" MatchDevicePath "/dev/input/event*" Driver "wacom" EndSection # N-Trig Duosense Electromagnetic Digitizer Section "InputClass" Identifier "Wacom N-Trig class" MatchProduct "HID 1b96:0001|N-Trig Pen" MatchDevicePath "/dev/input/event*" Driver "wacom" Option "Button2" "3" EndSection Section "InputDevice" Driver "wacom" Identifier "stylus" Option "USB" "on" Option "Device" "/dev/input/wacom" Option "Type" "stylus" Option "Threshold" "5" Option "Mode" "Relative" EndSection Section "InputDevice" Driver "wacom" Identifier "eraser" Option "USB" "on" Option "Device" "/dev/input/wacom" Option "Type" "eraser" Option "Mode" "Relative" Option "Threshold" "5" EndSection Section "InputDevice" Driver "wacom" Identifier "cursor" Option "USB" "on" Option "Device" "/dev/input/wacom" Option "Type" "cursor" Option "Mode" "Relative" EndSection
Notice that I added Atmel to the MatchProduct entry in the first section. Also notice the three input devices at the bottom stylus, eraser, and cursor.
After a reboot if listing wacom devices comes up empty, refer to Wacom Tablet to manually confugure. Upon rebooting I had a soft link to the proper input in /dev/input/ if setting up manually make sure your device option in the above config points to the proper event.
To list wacom devices run:
xsetwacom --list devices
Once you have that set up and your devices are being listed you should have full wacom functionality including pressure sensitivty. I tested this with xournal for note taking, and mypaint/gimp.
If you cannot get the synaptics driver to recognize a 3-finger click, this bug is probably the culprit: https://bugs.freedesktop.org/show_bug.cgi?id=55365 You can fix it by commenting out the call to clickpad_guess_clickfingers in the synaptics driver:
fixing synaptics manually
git clone git://anongit.freedesktop.org/xorg/driver/xf86-input-synaptics vi src/synaptics.c ./autogen.sh make sudo make install
It will be installed in /usr/local/lib/xorg/modules/input by default, though.
The next issue was how to rotate the screen when in tablet modes. Well there are two ways to do this, the first is Magick Rotate an originally Ubuntu based auto rotation utility. It does setup automatic rotation based on events and detaching the screen triggered the rotation.
If you don't want the screen to automatically rotate, you can manually do it through side buttons or an icon using this script:
Screen rotation script
#!/bin/sh #Gets the current mode of the screen mode="$(xrandr -q --verbose | grep 'connected' | egrep -o '\) (normal|left|inverted|right) \(' | egrep -o '(normal|left|inverted|right)')" case "$mode" in normal) #toggle rotate to the left xrandr -o left xsetwacom set "Atmel Atmel maXTouch Digitizer touch" Rotate ccw xsetwacom set "Wacom ISDv4 EC Pen stylus" Rotate ccw xsetwacom set "Wacom ISDv4 EC Pen eraser" Rotate ccw ;; left) #toggle rotate to normal xrandr -o normal xsetwacom set "Atmel Atmel maXTouch Digitizer touch" Rotate none xsetwacom set "Wacom ISDv4 EC Pen stylus" Rotate none xsetwacom set "Wacom ISDv4 EC Pen eraser" Rotate none ;; esac
First it grabs the current rotation, and will then toggle the state between left and normal states. Feel free to add to this for inverted or right rotations as well.
xsetwacom --list devices rename the wacom devices in the script.
Ambient light sensor
This machine has one, but it's not showing up as an ACPI device yet. Calise is one alternative for managing the screen brightness using the camera to detect ambient light.