Difference between revisions of "Lighttpd"

From ArchWiki
Jump to navigation Jump to search
Line 253: Line 253:
To make lighttpd SSL-only (you probably need to set the server port to 443 as well)
To make lighttpd SSL-only (you probably need to set the server port to 443 as well)
  ssl.engine = "enable"  
  ssl.engine = "enable"  
ssl.ca-file = "/etc/lighttpd/certs/ca.pem"
  ssl.pemfile = "/etc/lighttpd/certs/www.example.com.pem"
  ssl.pemfile = "/etc/lighttpd/certs/www.example.com.pem"
To enable SSL in addition to normal HTTP
To enable SSL in addition to normal HTTP

Revision as of 20:29, 25 May 2016

zh-CN:Lighttpd zh-TW:Lighttpd Lighttpd is "a secure, fast, compliant, and very flexible web-server that has been optimized for high-performance environments. It has a very low memory footprint compared to other webservers and takes care of cpu-load. Its advanced feature-set (FastCGI, CGI, Auth, Output-Compression, URL-Rewriting and many more) make lighttpd the perfect webserver-software for every server that suffers load problems."


Install the lighttpd package.


Basic Setup

The lighttpd configuration file is: /etc/lighttpd/lighttpd.conf. By default it should produce a working test page.

To check your lighttpd.conf for bugs you can use this command - helps finding misconfigurations very fast:

$ lighttpd -t -f /etc/lighttpd/lighttpd.conf

The default configuration file specifies /srv/http/ as the document directory served. To test the installation, create a dummy file:

Hello world!

Then start/enable the lighttpd.service and point your browser to localhost, where you should see the test page.

Example configuration files are available in /usr/share/doc/lighttpd/.


Common Gateway Interface (CGI) scripts work with Lighttpd out of box, you just need to enable the CGI module, include the configuration file and make sure your chosen programming language interpreter is installed. (i.e. for python you would install python)

Create the file /etc/lighttpd/conf.d/cgi.conf Add the following to it:

server.modules += ( "mod_cgi" )

cgi.assign                 = ( ".pl"  => "/usr/bin/perl",
                               ".cgi" => "/usr/bin/perl",
                               ".rb"  => "/usr/bin/ruby",
                               ".erb" => "/usr/bin/eruby",
                               ".py"  => "/usr/bin/python",
                               ".php" => "/usr/bin/php-cgi" )

index-file.names           += ( "index.pl",   "default.pl",
                               "index.rb",   "default.rb",
                               "index.erb",  "default.erb",
                               "index.py",   "default.py",
                               "index.php",  "default.php" )

For PHP scripts you will need to make sure the following is set in /etc/php/php.ini

cgi.fix_pathinfo = 1

In your Lighttpd configuration file, /etc/lighttpd/lighttpd.conf add:

include "conf.d/cgi.conf"


Install fcgi. Now you have lighttpd with fcgi support. If it was that what you wanted you are all set. People that want Ruby on Rails, PHP or Python should continue.

Note: New default user and group: Instead of group nobody lighttpd now runs as user/group http by default.

First copy the example config file form /usr/share/doc/lighttpd/config/conf.d/fastcgi.conf to /etc/lighttpd/conf.d

The following needs adding to the config file, /etc/lighttpd/conf.d/fastcgi.conf

server.modules += ( "mod_fastcgi" )

#server.indexfiles += ( "dispatch.fcgi" ) #this is deprecated
index-file.names += ( "dispatch.fcgi" ) #dispatch.fcgi if rails specified

server.error-handler-404   = "/dispatch.fcgi" #too
fastcgi.server = (
    ".fcgi" => (
      "localhost" => ( 
        "socket" => "/run/lighttpd/rails-fastcgi.sock",
        "bin-path" => "/path/to/rails/application/public/dispatch.fcgi"

Then in /etc/lighttpd/lighttpd.conf:

include "conf.d/fastcgi.conf"

For PHP or Ruby on Rails see the next sections.


Install php and php-cgi (see also PHP and LAMP).

Check that php-cgi is working php-cgi --version

PHP 5.4.3 (cgi-fcgi) (built: May  8 2012 17:10:17)
Copyright (c) 1997-2012 The PHP Group
Zend Engine v2.4.0, Copyright (c) 1998-2012 Zend Technologies

If you get a similar output then php is installed correctly.

Create a new configuration file:

# Make sure to install php and php-cgi. See:                                                             
# https://wiki.archlinux.org/index.php/Fastcgi_and_lighttpd#PHP

server.modules += ("mod_fastcgi")

# FCGI server
# ===========
# Configure a FastCGI server which handles PHP requests.
index-file.names += ("index.php")
fastcgi.server = ( 
    # Load-balance requests for this path...
    ".php" => (
        # ... among the following FastCGI servers. The string naming each
        # server is just a label used in the logs to identify the server.
        "localhost" => ( 
            "bin-path" => "/usr/bin/php-cgi",
            "socket" => "/tmp/php-fastcgi.sock",
            # breaks SCRIPT_FILENAME in a way that PHP can extract PATH_INFO
            # from it 
            "broken-scriptfilename" => "enable",
            # Launch (max-procs + (max-procs * PHP_FCGI_CHILDREN)) procs, where
            # max-procs are "watchers" and the rest are "workers". See:
            # https://redmine.lighttpd.net/projects/1/wiki/frequentlyaskedquestions#How-many-php-CGI-processes-will-lighttpd-spawn 
            "max-procs" => 4, # default value
            "bin-environment" => (
                "PHP_FCGI_CHILDREN" => "1" # default value

Make lighttpd use the new configuration file:

include "conf.d/fastcgi.conf"
Note: Remember that the order in which the modules are loaded is important, the correct order is listed in /usr/share/doc/lighttpd/config/modules.conf. Any misconfiguration may cause lighttpd to crash.

Reload lighttpd.

  • If you receive errors like No input file found when attempting to access php files, there are several possible explanations. See this FAQ for more information.
  • Make sure that no other module (e.g. mod_cgi) will try to handle the .php extension.
Using php-fpm

There is no adaptive spawning anymore in recent lighttpd releases. For dynamic management of PHP processes, you can install php-fpm and then start and enable php-fpm.service.

Note: You can configure the number of servers in the pool and tweak other configuration options by editing the file /etc/php/php-fpm.conf. More details on php-fpm can be found on the php-fpm website. Remember that when you make changes to /etc/php/php.ini you will need to restart php-fpm.service.

In /etc/lighttpd/conf.d/fastcgi.conf add:

server.modules += ( "mod_fastcgi" )

index-file.names += ( "index.php" ) 

fastcgi.server = (
    ".php" => (
      "localhost" => ( 
        "socket" => "/run/php-fpm/php-fpm.sock",
        "broken-scriptfilename" => "enable"
Note: As of November 2014, eacceleratorAUR[broken link: archived in aur-mirror] cannot be compiled.

Install eacceleratorAUR[broken link: archived in aur-mirror].

Add own config file for eaccelerator:

zlib.output_compression = On
Tip: I additionally set safe_mod to On in my setup, but this is not required.
Try a php page

Create the following php page, name it index.php, and place a copy in both /srv/http/ and /srv/http-ssl/html/


Try navigating with a web browser to both the http and https address of your server. You should see the phpinfo page.

Check eaccelerator caching:

# ls -l /home/phpuser/eaccelerator/cache

If the above command outputs the following:

-rw-------  1 phpuser phpuser 456 2005-05-05 14:53 eaccelerator-277.58081
-rw-------  1 phpuser phpuser 452 2005-05-05 14:53 eaccelerator-277.88081

Then eaccelerator is happily caching your php scripts to help speed things up.

Ruby on Rails

Install and configure FastCGI (see #FastCGI above).

Install ruby from official repositories and ruby-fcgiAUR[broken link: archived in aur-mirror] from AUR.

Follow instructions on RubyOnRails.

Python FastCGI

Note: This method will not work with Python 3 because Flup library is only available for Python 2. If you want to use Python 3, you should refer to #CGI section.

Install and configure FastCGI (see #FastCGI above).

Install python2-flup.


fastcgi.server = (
    ".py" =>
        "python-fcgi" =>
        "socket" => "/run/lighttpd/fastcgi.python.socket",
         "bin-path" => "test.py",
         "check-local" => "disable",
         "max-procs" => 1,

Put the test.py in the root of your server (do not forget to chmod +x it)

#!/usr/bin/env python2

def myapp(environ, start_response):
    print 'got request: %s' % environ
    start_response('200 OK', [('Content-Type', 'text/plain')])
    return ['Hello World!']

if __name__ == '__main__':
    from flup.server.fcgi import WSGIServer

Thanks to firecat53 for his explanation


Warning: If you plan on implementing SSL/TLS, know that some variations and implementations are still vulnerable to attack. For details on these current vulnerabilities within SSL/TLS and how they apply to Lighttpd and other services (such as email) visit http://disablessl3.com/ and https://weakdh.org/sysadmin.html

Generate an SSL Cert, e.g. like that:

# mkdir /etc/lighttpd/certs
# openssl req -x509 -nodes -days 7300 -newkey rsa:2048 -sha256 -keyout /etc/lighttpd/certs/www.example.com.pem -out /etc/lighttpd/certs/www.example.com.pem
# chmod 600 /etc/lighttpd/certs/www.example.com.pem

Edit /etc/lighttpd/lighttpd.conf. To make lighttpd SSL-only (you probably need to set the server port to 443 as well)

ssl.engine = "enable" 
ssl.ca-file = "/etc/lighttpd/certs/ca.pem"
ssl.pemfile = "/etc/lighttpd/certs/www.example.com.pem"

To enable SSL in addition to normal HTTP

$SERVER["socket"] == ":443" {
    ssl.engine                  = "enable" 
    ssl.ca-file                 = "/etc/lighttpd/certs/ca.pem"
    ssl.pemfile                 = "/etc/lighttpd/certs/www.example.com.pem" 

If you want to serve different sites, you can change the document root inside the socket conditional:

$SERVER["socket"] == ":443" {
    server.document-root = "/srv/ssl" # use your ssl directory here
    ssl.engine                 = "enable"
    ssl.ca-file                = "/etc/lighttpd/certs/ca.pem"
    ssl.pemfile                = "/etc/lighttpd/certs/www.example.com.pem"  # use the path where you created your pem file

or as alternative you can use the scheme conditional to distinguish between secure and normal requests.

$HTTP["scheme"] == "https" {
    server.document-root = "/srv/ssl" # use your ssl directory here
    ssl.engine                 = "enable"
    ssl.ca-file                = "/etc/lighttpd/certs/ca.pem"
    ssl.pemfile                = "/etc/lighttpd/certs/www.example.com.pem"  # use the path where you created your pem file

Note that you cannot use the scheme conditional around ssl.engine above, since lighttpd needs to know on what port to enable SSL.

Server Name Indication

To use SNI with lighttpd, simply put additional ssl.pemfile configuration directives inside host conditionals. A default ssl.pemfile is still required.

$HTTP["host"] == "www.example.org" {
    ssl.pemfile = "/etc/lighttpd/certs/www.example.org.pem" 

$HTTP["host"] == "mail.example.org" {
    ssl.pemfile = "/etc/lighttpd/certs/mail.example.org.pem" 

Redirect HTTP requests to HTTPS

You should add "mod_redirect" in server.modules array in /etc/lighttpd/lighttpd.conf:

server.modules += ( "mod_redirect" )

$SERVER["socket"] == ":80" {
  $HTTP["host"] =~ "example.org" {
    url.redirect = ( "^/(.*)" => "https://example.org/$1" )
    server.name                 = "example.org" 

$SERVER["socket"] == ":443" {
  ssl.engine = "enable" 
  ssl.pemfile = "/etc/lighttpd/ssl/server.pem" 
  server.document-root = "..." 

To redirect all hosts to their secure equivalents use the following in place of the socket 80 configuration above:

$SERVER["socket"] == ":80" {
  $HTTP["host"] =~ ".*" {
    url.redirect = (".*" => "https://%0$0")

To redirect all hosts for part of the site (e.g. secure or phpmyadmin):

$SERVER["socket"] == ":80" {
  $HTTP["url"] =~ "^/secure" {
    url.redirect = ( "^/(.*)" => "https://example.com/$1" )

Output Compression

In /etc/lighttpd/lighttpd.conf add

var.cache_dir           = "/var/cache/lighttpd"

Then create directory for a compressed files:

# mkdir /var/cache/lighttpd/compress
# chown http:http /var/cache/lighttpd/compress

Copy example configuration file:

# mkdir /etc/lighttpd/conf.d
# cp /usr/share/doc/lighttpd/config/conf.d/compress.conf /etc/lighttpd/conf.d/

Add following in /etc/lighttpd/lighttpd.conf:

include "conf.d/compress.conf"
Note: You can not do this (copy compress.conf) and add a needed content in /etc/lighttpd/lighttpd.conf instead.

See also