MAC address spoofing

From ArchWiki
Revision as of 20:47, 17 July 2014 by Adamlau (talk | contribs) (systemd + macchanger + dhcpcd (no NetworkManager).)
Jump to navigation Jump to search

zh-CN:MAC Address Spoofing This article gives several methods to spoof a Media Access Control (MAC) address.


There are two methods for spoofing a MAC address using either iproute2 (installed by default) or macchanger (available on the official repositories). Both of them are outlined below.

Method 1: iproute2

First, you can check your current MAC address with the command:

# ip link show interface

where interface is the name of your network interface.

The section that interests us at the moment is the one that has "link/ether" followed by a 6-byte number. It will probably look something like this:

link/ether 00:1d:98:5a:d1:3a

The first step to spoofing the MAC address is to bring the network interface down. It can be accomplished with the command:

# ip link set dev interface down

Next, we actually spoof our MAC. Any hexadecimal value will do, but some networks may be configured to refuse to assign IP addresses to a client whose MAC does not match up with a vendor. Therefore, unless you control the network(s) you are connecting to, it is a good idea to test this out with a known good MAC rather than randomizing it right away.

To change the MAC, we need to run the command:

# ip link set dev interface address XX:XX:XX:XX:XX:XX

Where any 6-byte value will suffice for XX:XX:XX:XX:XX:XX.

The final step is to bring the network interface back up. This can be accomplished by running the command:

# ip link set dev interface up

If you want to verify that your MAC has been spoofed, simply run ip link show interface again and check the value for 'link/ether'. If it worked, 'link/ether' should be whatever address you decided to change it to.

Method 2: macchanger

Another method uses macchanger (a.k.a., the GNU MAC Changer). It provides a variety of features such as changing the address to match a certain vendor or completely randomizing it.

Install the package macchanger from the official repositories.

The spoofing is done on per-interface basis, specify network interface name as interface in each of the following commands.

The MAC address can be spoofed with a fully random address:

# macchanger -r interface

To randomize all of the address except for the vendor bytes (that is, so that if the MAC address was checked it would still register as being from the same vendor), you would run the command:

# macchanger -e interface

To change the MAC address to a specific value, you would run:

# macchanger --mac=XX:XX:XX:XX:XX:XX interface

Where XX:XX:XX:XX:XX:XX is the MAC you wish to change to.

Finally, to return the MAC address to its original, permanent hardware value:

# macchanger -p interface
Note: A device cannot be in use (connected in any way or with its interface up) while the MAC address is being changed.


systemd + iproute2 + dhcpcd.

systemd unit setting a predefined MAC address while assuming the use of dhcpcd.

Description=MAC Address Change %I

ExecStart=/usr/bin/ip link set dev %i address 36:aa:88:c8:75:3a
ExecStart=/usr/bin/ip link set dev %i up


You may have to edit this file if you do not use dhcpcd.

systemd + macchanger + GNOME NetworkManager

systemd unit setting a random address while preserving the original NIC vendor bytes. Ensure that macchanger is first installed.

Description=macchanger on %I

ExecStart=/usr/bin/macchanger -e %I


systemd + macchanger + dhcpcd (no NetworkManager).

systemd unit setting a fully random address while assuming the use of dhcpcd without NetworkManager. Ensure that macchanger is first installed

Description=macchanger on %I

ExecStart=/usr/bin/macchanger -r %I


Append the desired network interface(s) to the service name (e.g. eth0) and install the service(s).

# systemctl enable macspoof@eth0.service

Reboot, or restart the prerequisite and requisite services in the proper order. If you are in control of your network, verify that the spoofed MAC has been picked up by your router by examining the static, or DHCP address tables within the router.

See also