MSI Wind U100
This article pertains to the MSI Wind U100 netbook/sub-notebook.
- CPU: Intel Atom N270 1.6Ghz
- RAM: 1024 Mb, DDR2 667Mhz (optional)
- HDD: WD 80Gb SATA (optional)
- VGA: Intel 945 GMA, 64 MB DDR
- LCD: 1024x600, 10.2" widescreen
- WLAN: Realtek RTL8187SE , 802.11 a/b/g
- LAN: Realtek RTL8101/02
- CAM: 1.3 Mpix
- BAT: LI-ON 3 cell 2200 mAh, 2 hours (optional)
- Bluetooth, card reader, 3x USB 2.0
- Touchpad: Synaptics or Sentelic
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8187SE Wireless LAN Controller (rev 22)
Some have other wireless cards:
02:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01)
There are several possible ways to install Arch onto a MSI Wind U100. The most usual methods are booting from a USB stick/memory card, or from an external CD/DVD drive. Refer to the Beginners' Guide CD installer part for instructions on obtaining an ISO image and burning to a CD, or consult the USB stick section for indications on writing the image to a USB device.
Regardless of choice, finish by hooking up the external device (CD drive or USB stick) to the notebook. Hold the F11 key while booting in order to get to the boot device menu, then proceed by selecting the appropriate device and install as normal.
you should use acpi-cpufreq driver which will allow you to slow down your CPU to 800MHz (p4-clockmod driver will work too, but it's not intended to be used with governors like ondemand, it should be used just for manual underclocking usig hotkeys or ACPI events like AC-disconnection because it's too slow to react fast enough to be suitable for use with automatic scaling based on CPU usage and therefore kernel will refuse to use such governors. however you can underclock cpu down to 200MHz using this driver). Probably you will also want to use cpufreq-ondemand governor.
It is possible to overclock the MSI Wind using an upgraded BIOS. The overclock (turbo mode) can be activated with Fn+F10, however, this overclock is not reported in /proc/cpuinfo or by cpufreq-info.
Audio is supported through ALSA with virtually no configuration. Following the ALSA article should cover all that is needed.
The on-board graphics uses the Intel driver. To install with pacman:
# pacman -S xf86-video-intel
First, do not forget to activate the webcam with the hotkey Fn+F6. If it's still not working, then try loading the module. The webcam should be supported through the
uvcvideo module by default, if not:
# modprobe uvcvideo
To load the webcam driver automatically, adding uvcvideo to the
MODULES array in Template:Filename may be needed:
The webcam uses a resolution of 640x480. As a warning, recording video with higher resolutions may result in a lower framerate.
Determine which card the particular u100 version has by running
lspci. These are the possibilities:
- Realtek 8187se B/G
- Ralink RT2860 B/G/N
- Atheros AR928X B/G/N
lspci output should mention the company name.
Since kernel 2.6.29 there's a working driver included in the staging line. The module is
rtl8187se and should get loaded without intervention. This network adapter is known to be buggy, so it's unlikely that this driver will show significant progress over its current state. Using ndiswrapper in place of the in-kernel module is recommended because of this situation.
The RT2860 now works out of the box with rt2x00pci drivers.
AR5001 (rev 02) works out of the box with ath5k or mad wifi drivers.
Some versions of MSI Wind do have internal USB bluetooth module. It should be autodetected (using modules btusb, bluetooth and rfkill). However there is bug (probably in kernel) that prevent's people from toggling bluetooth using fn+f11 if it wasn't active during boot. (toggling wifi using fn+f11 remains working) If you happen to reboot your linux with BT deactivated, you will probably need to use windows or some distribution without this bug (BackTrack 4 was reported to work) to activate it again. There is hope this will be fixed in future. (please let us know if you will find any solution for this issue)
The Sentelic Finger Sensing Pad driver (version 1.0.0) is included in kernel 2.26.32 and above, however, it may be difficult to get the configuration utility (fspc) to work correctly. It is possible to configure the pad manually by adding the following lines to your /etc/rc.local
# Disable tap-to-click: echo -n c>>/sys/devices/platform/i8042/serio1/flags # Disable vertical tap scrolling: echo -e \0>>/sys/devices/platform/i8042/serio1/vscroll # Disable horizontal tap scrolling: echo -e \0>>/sys/devices/platform/i8042/serio1/hscroll
The Ethernet adapter functions thanks to the
r8169 module present in kernels 2.26.31 and newer.
Memory stick reader
The multi-card reader appears to work automatically.