From ArchWiki
Revision as of 06:31, 19 October 2012 by Uwolfer (talk | contribs) (The installation)
Jump to navigation Jump to search

Template:Article summary start Template:Article summary text Template:Article summary heading Template:Article summary wiki Template:Article summary wiki Template:Article summary wiki Template:Article summary wiki Template:Article summary end


This page should help you setting up ArchLinux on a MacBook Pro 10,1 with Retina display. Most of the steps are the same or very similar to the regular ArchLinux installation. However, because this is very new hardware, the setup requires a few different steps. The general installation guidelines are descibed in MacBook.

Preparing for the Installation

Preparing the Hard drive

Assuming you want to have a dual boot with Mac OS X, boot into Mac OS and shrink it's partition with the Disk Utility. You can either create your Linux partition directly here, or do that later in Linux during the installation (using parted and mkfs).

Getting wireless firmware

In order for the WiFi chip to work, you need to get the firmware for it. There are various ways to do so. You can juts copy it from another b43 enabled archlinux box, extract it from Broadcoms driver using b43-fwcutter or get them through the b43-firmware package[1] in AUR. In the end you should have a folder "b43" with lots of .fw files in it.


Booting the live image

Now, download the latest Archboot iso, write it to USB and boot from it by selecting it in the Apple boot loader. When it comes to the syslinux boot loader, press [tab] to edit the entry and append "noapic" or "nointremap" to the end to prevent a kernel panic during bootup. Currently (august 4, 2012), you also have to add "nomodeset".

Connecting WiFi

Note: You can skip this if you use the USB to ethernet adapter for the installation.

After it has finished booting, enter a command line. Copy the entire folder with the firmware for your wireless card to /lib/firmware/. Now you should be able to use wpa_supplicant to connect to your WiFi network.

The installation

Note: There are also other ways of booting the kernel. Refer to the MacBook page if you don't want to have a separate partition for grub but rather prefer to use refind (or refit). It works very well with refind without hacks and problems. You can ignore the following lines if you go the refind-way.

Run the installation wizard. When asked to partition your hard drive, create a small HFS partition. This is where you put the standalone grub package after the installation. The rest of the installation is pretty much the same as usual. When choosing the bootloader, select grub2 and install it. Don't worry about any errors, we will create the bootable efi image on our own afterwards.

After the installation has completed, directly copy the WiFi firmware to the installed system to /tmp/install/usr/lib/firmware.

update the kernel

Best results are obtained with the 3.5 kernel. To date, you can install it from [testing] or from the AUR linux-mainline. To get keyboard backlight and Bluetooth working, apply this patch.

3.6-rc6 (and up) include all the patches needed for applesmc, i915, bluetooth and apple-gmux. You can install it from AUR (or soon from [testing] or [core]. It might not include the nouveau patches yet (not sure).


Direct EFI booting

You can directly boot from the kernel, in which case there is no bootloader per se (the kernel is its own bootloader). This is described elsewhere in UEFI_Bootloaders section EFISTUB. In a nutshell, you have to put kernel and initramfs in a linux directory of your EFI partition (sda1), together with a file containing the kernel boot parameters.


Another solution is to install GRUB2. Edit /tmp/install/boot/grub/grub.cfg and edit the boot entry to load linux-mainline instead of the normal one. Also append "noapic" to the kernel line again.

Now cd into /tmp/install and create the grub image by calling:

grub-mkstandalone -o grub-standalone-x86_64.efi -d usr/lib/grub/x86_64-efi -O x86_64-efi -C xz boot/grub/grub.cfg

This will create file called grub-standalone-x86_64.efi which contains grub and the config file. It is important to do cd into the right directory to make it pick up the config file and put it into the right place within the image. Copy this file to the HFS partition you have created earlier. Downside of this method is that you need to repeat this step whenever you want to change the grub config.

Reboot the machine and boot into Mac OS. The HFS partition should be mounted and the grub standalone image in there. Follow the steps on this page to create the files needed to make the Apple boot loader pick up grub: After creating the files, use "bless" on the grub image on the partition, if you want to boot automatically to Arch, append --setBoot.

After another reboot, you should be able to select your installed Arch Linux by keeping the alt button pressed while booting in case you haven't used --setBoot while blessing.

Post installation


The Laptop comes with an nVidia and a Intel chip. The i915 (from 3.6-rc5) and proprietary nvidia (from 302.17) drivers work. You can install the proprietary nvidia driver from [testing] (recommended) or from the AUR nvidia-beta-all, or download the nVidia installer from their website (not recommended, always install things through pacman to avoid file conflicts).


Because of the integrated button, the synaptics touchpad driver caused issues for me. Installing xf86-input-mtrack and adjusting its config produced way better results.


Suspend should work fine with the i915 or nvidia drivers.

In case you encounter problems with resuming when using the nvidia driver, try the --quirk-dpms-on quirk. You can add a "99local" file in /etc/pm/config.d/ with the following content:


What doesn't work (early September 2012, 3.6-rc6)

  • Microphone (white noise at all times)
  • Suspend mode on lid close with nouveau and i915 (does not come out of suspend; blank screen).


Here are a couple of interesting threads: