Difference between revisions of "Mouse polling rate"

From ArchWiki
Jump to: navigation, search
(Saving my work just in case)
 
m (Displaying current mouse rate)
(28 intermediate revisions by 14 users not shown)
Line 1: Line 1:
If you have invested in a high resolution mouse, adjusting the USB polling rate is a common trick to utilise the added precision it brings. The polling rate (or report rate) determines how often (per second) the mouse sends information to your computer. Measured in ''Hz'', this setting equates to lag time (in ''ms'').
+
[[Category:Mice]]
 +
If you have invested in a high resolution mouse, adjusting the USB polling rate is a common trick to utilise the added precision it brings. The polling rate (or report rate) determines how often the mouse sends information to your computer. Measured in ''Hz'', this setting equates to lag time (in ''ms'').
  
 
By default, the USB polling rate is set at 125hz. The table below represents combinations of ''Hz'' values and their corresponding delay time:
 
By default, the USB polling rate is set at 125hz. The table below represents combinations of ''Hz'' values and their corresponding delay time:
Line 25: Line 26:
 
If the polling rate is set at 125 Hz, the mouse cursor can only be updated every 8 milliseconds. In situations where lag is critical (for example games), it is useful to decrease this value to as little as possible. Increasing the polling interval will improve precision at the tradeoff of using more CPU resources, therefore care should be taken when adjusting this value.
 
If the polling rate is set at 125 Hz, the mouse cursor can only be updated every 8 milliseconds. In situations where lag is critical (for example games), it is useful to decrease this value to as little as possible. Increasing the polling interval will improve precision at the tradeoff of using more CPU resources, therefore care should be taken when adjusting this value.
  
== Further Reading ==
+
== Setting the polling rate ==
[http://www.overclock.net/computer-peripherals/173255-cs-s-mouse-optimization-guide.html CS:S Mouse Optimization Guide] -- largely aimed at Windows users, though the same principles apply for Linux.
+
Here we are using the {{ic|usbhid}} module of the kernel to set a custom "mousepoll" rate. Simply add the following line to your {{ic|/etc/modprobe.d/modprobe.conf}} file:
  
[http://www.linux-gamers.net/modules/wiwimod/index.php?page=HOWTO+USBPolling Increase Mouse Polling Rate Interval]
+
options usbhid mousepoll=[polling interval]
[http://tscherwitschke.de/mouseratechecker.html Mouse Rate Checker] (Windows)
+
 
 +
(where [polling interval] is a number in ''ms'' from the table above. For example, to set a polling rate of 500Hz:
 +
 
 +
options usbhid mousepoll=2
 +
 
 +
To change the polling rate without rebooting
 +
 
 +
modprobe -r usbhid && modprobe usbhid
 +
 
 +
{{Warning|Make sure that both commands execute otherwise you will be unable to use the mouse and keyboard and will have to reboot or ssh into your machine.}}
 +
 
 +
Then unplug and replug your mouse.
 +
 
 +
{{Note|1=If you use the '''usbinput''' and '''udev''' hooks in your initramfs, usbhid will included on the image and you'll need to add {{ic|/etc/modprobe.d/modprobe.conf}} to the FILES entry in {{ic|/etc/mkinitcpio.conf}}. Remember to regenerate your image after changing the config. Without doing this, the module will be inserted during early userspace without the polling option. Alternatively, you can add usbhid.mousepoll=X to your kernel command line.}}
 +
 
 +
== Displaying current mouse rate ==
 +
A tool exists (named ''evhz'') that can display the current mouse refresh rate -- useful when checking that your customized polling settings have been applied.
 +
 
 +
[https://github.com/ian-kelling/evhz/raw/master/evhz.c evhz.c]
 +
 
 +
Compile it with:
 +
 
 +
gcc -o evhz evhz.c
 +
 
 +
Then execute as root:
 +
 
 +
./evhz
 +
 
 +
Alternatively, Windows tools such as [http://razerblueprints.net/index.php/View-document-details/18-DirectX-mouserate-checker.html DirectX mouserate checker] can be run using WINE.
 +
 
 +
== Further Reading ==
 +
*[http://www.overclock.net/computer-peripherals/173255-cs-s-mouse-optimization-guide.html CS:S Mouse Optimization Guide] -- largely aimed at Windows users, though the same principles apply for Linux.

Revision as of 20:19, 10 October 2013

If you have invested in a high resolution mouse, adjusting the USB polling rate is a common trick to utilise the added precision it brings. The polling rate (or report rate) determines how often the mouse sends information to your computer. Measured in Hz, this setting equates to lag time (in ms).

By default, the USB polling rate is set at 125hz. The table below represents combinations of Hz values and their corresponding delay time:

Hz ms
1000 1
500 2
250 4
125 8
100 10

If the polling rate is set at 125 Hz, the mouse cursor can only be updated every 8 milliseconds. In situations where lag is critical (for example games), it is useful to decrease this value to as little as possible. Increasing the polling interval will improve precision at the tradeoff of using more CPU resources, therefore care should be taken when adjusting this value.

Setting the polling rate

Here we are using the usbhid module of the kernel to set a custom "mousepoll" rate. Simply add the following line to your /etc/modprobe.d/modprobe.conf file:

options usbhid mousepoll=[polling interval]

(where [polling interval] is a number in ms from the table above. For example, to set a polling rate of 500Hz:

options usbhid mousepoll=2

To change the polling rate without rebooting

modprobe -r usbhid && modprobe usbhid
Warning: Make sure that both commands execute otherwise you will be unable to use the mouse and keyboard and will have to reboot or ssh into your machine.

Then unplug and replug your mouse.

Note: If you use the usbinput and udev hooks in your initramfs, usbhid will included on the image and you'll need to add /etc/modprobe.d/modprobe.conf to the FILES entry in /etc/mkinitcpio.conf. Remember to regenerate your image after changing the config. Without doing this, the module will be inserted during early userspace without the polling option. Alternatively, you can add usbhid.mousepoll=X to your kernel command line.

Displaying current mouse rate

A tool exists (named evhz) that can display the current mouse refresh rate -- useful when checking that your customized polling settings have been applied.

evhz.c

Compile it with:

gcc -o evhz evhz.c

Then execute as root:

./evhz

Alternatively, Windows tools such as DirectX mouserate checker can be run using WINE.

Further Reading