OpenLDAP, LDAP & Directory services are an enormous topic. Configuration is therefore complex. This page is a starting point for a basic OpenLDAP installation and a sanity check.
If you are totally new to those concepts, this is an good introduction that is easy to understand and that will get you started, even if you are new to everything LDAP.
OpenLDAP contains both a LDAP server and client. Install it with the package official repositories., available in the
The server configuration file is located at
Edit the suffix and rootdn. The suffix typically is your domain name but it does not have to be. It depends on how you use your directory. We will use example for the domain name, and com for the tld. The rootdn is your LDAP administrator's name (we'll use root here).
suffix "dc=example,dc=com" rootdn "cn=root,dc=example,dc=com"
Now we delete the default root password and create a strong one:
# sed -i "/rootpw/ d" slapd.conf #find the line with rootpw and delete it # echo "rootpw $(slappasswd)" >> slapd.conf #add a line which includes the hashed password output from slappasswd
You will likely want to add some typically used schemas to the top of
include /etc/openldap/schema/cosine.schema include /etc/openldap/schema/inetorgperson.schema include /etc/openldap/schema/nis.schema
You will likely want to add some typically used indexes to the bottom of
index uid pres,eq index mail pres,sub,eq index cn pres,sub,eq index sn pres,sub,eq index dc eq
Now prepare the run directory:
# mkdir /run/openldap # chown ldap:ldap /run/openldap
Now prepare the database directory. You will need to copy the default config file and set the proper ownership:
# cp /etc/openldap/DB_CONFIG.example /var/lib/openldap/openldap-data/DB_CONFIG # chown ldap:ldap /var/lib/openldap/openldap-data/DB_CONFIG
Perform an intial index after you populate your directory:
# slapindex # chown ldap:ldap /var/lib/openldap/openldap-data/*
Finally you can start the slapd daemon with
slapd.service using systemd.
If you want to use SSL, see #OpenLDAP over TLS.
The client config file is located at
It is quite simple: you'll only have to alter
BASE to reflect the suffix of the server, and
URI to reflect the address of the server.
If you decide to use SSL:
- The protocol (ldap or ldaps) in the
URIentry has to conform with the slapd configuration
- If you decide to use self-signed certificates, add a
Test your new OpenLDAP installation
This is easy, just run the command below:
ldapsearch -x '(objectclass=*)'
Or authenticating as the rootdn (replacing
-D <user> -W), using the example configuration we had above:
ldapsearch -D "cn=root,dc=example,dc=com" -W '(objectclass=*)'
Now you should see some information about your database.
OpenLDAP over TLS
If you access the OpenLDAP server over the network and especially if you have sensitive data stored on the server you run the risk of someone sniffing your data which is sent clear-text. The next part will guide you on how to setup an SSL connection between the LDAP server and the client so the data will be sent encrypted.
In order to use TLS, we must first create a certificate. You can have a certificate signed, or create your own Certificate Authority (CA), but for our purposed, a self-signed certificate will suffice.
Create a self-signed certificate
To create a self-signed certificate, type the following:
$ openssl req -new -x509 -nodes -out slapdcert.pem -keyout slapdkey.pem -days 365
You will be prompted for information about your LDAP server. Much of the information can be left blank. The most important information is the common name. This must be set to the DNS name of your LDAP server. If your LDAP server's IP address resolves to example.org but its server certificate shows a CN of bad.example.org, LDAP clients will reject the certificate and will be unable to negotiate TLS connections (apparently the results are wholly unpredictable).
Now that the certificate files have been created copy them to
/etc/openldap/ssl/ (if this directory doesn't exist create it) and secure them.
slapdcert.pem must be world readable because it contains the public key.
slapdkey.pem on the other hand should only be readable for the ldap user for security reasons:
# cp slapdcert.pem slapdkey.pem /etc/openldap/ssl/ # chmod 400 slapdkey.pem # chmod 444 slapdcert.pem # chown ldap slapdkey.pem
Configure slapd for SSL
Edit the daemon configuration file (
/etc/openldap/slapd.conf) to tell LDAP where the certificate files reside by adding the following lines:
# Certificate/SSL Section TLSCipherSuite HIGH:MEDIUM:+SSLv2 TLSCertificateFile /etc/openldap/ssl/slapdcert.pem TLSCertificateKeyFile /etc/openldap/ssl/slapdkey.pem
The TLSCipherSuite specifies a list of OpenSSL ciphers from which slapd will choose when negotiating TLS connections, in decreasing order of preference. In addition to those specific ciphers, you can use any of the wildcards supported by OpenSSL. NOTE: HIGH, MEDIUM, and +SSLv2 are all wildcards.
openssl ciphers -v ALL
Start slapd with SSL
You will have to edit
slapd.service to change to protocol slapd listens on.
slapd.service if it's enabled.
Then, copy the stock service to
# cp /usr/lib/systemd/system/slapd.service /etc/systemd/system/
Edit it, and add
-h "ldaps:///" to
ExecStart. It should look like this:
ExecStart=/usr/bin/slapd -u ldap -g ldap -h "ldaps:///"
Then reenable and start it:
# systemctl daemon-reload # systemctl enable slapd.service # systemctl restart slapd.service
Localhost connections don't need to use SSL so you could replace
/etc/openldap/ldap.confor you won't be able connect to the server.
You now have a basic ldap installation. The step is to design your directory. The design is heavily dependent on what you are using it for. If you are new to ldap, consider starting with a directory design recommended by the specific client services that will use the directory (PAM, Postfix, etc).
A directory for system authentication is the LDAP Authentication article.
If you notice that slapd seems to start but then stops, you may have a permission issue with the ldap datadir. Try running:
# chown ldap:ldap /var/lib/openldap/openldap-data/*
to allow slapd write access to its data directory as the user "ldap"