From ArchWiki
Jump to navigation Jump to search

Tango-view-refresh-red.pngThis article or section is out of date.Tango-view-refresh-red.png

Reason: rc.d references, bad style/format. (Discuss in Talk:OpenNTPD#)

OpenNTPD (part of the OpenBSD project) is a daemon that can be used to synchronize the system clock to internet time servers using the Network Time Protocol, and can also act as a time server itself if needed.


Install the openntpd package. The default configuration is actually usable if all you want is to sync the time of the local computer. For more detailed settings, the /etc/ntpd.conf file must be edited:

To sync to a particular server, uncomment and edit the "server" directive. You can find the server's URL in your area at


The "servers" directive works the same as the "server" directive, however, if the DNS name resolves to multiple IP address, ALL of them will be synced to. The default, "" is working and should be acceptable in most cases.

Any number of "server" or "servers" directives may be used.

If you want the computer you run OpenNTPD on to also be a time server, simply uncomment and edit the "listen" directive.

For example:

listen on *

will listen on all interfaces, and

listen on

will only listen on the loopback interface.

Your time server will only begin to serve time after it has synchronized itself to a high resolution. This may take hours, or days, depending on the accuracy of your system.

Enable OpenNTPD through systemd

Start/enable the openntpd service.

Making openntpd dependent upon network access

If you have intermittent network access (you roam around on a laptop, you use dial-up, etc), it does not make sense to have openntpd running as a system daemon on start up. Here are a few ways you can control openntpd based on the presence of a network connection. These instructions should also work for ntpd found further below.

Using netcfg

If you are using netcfg, you can also start/stop openntpd as a POST_UP/PRE_DOWN command in your network profile:

POST_UP="/etc/rc.d/openntpd start || true"
PRE_DOWN="/etc/rc.d/openntpd stop || true"

Of course, you will have to specify this manually for each network profile.

Using NetworkManager dispatcher

OpenNTPD can be brought up/down along with a network connection through the use of NetworkManager's dispatcher scripts. You can install the needed script, networkmanager-dispatcher-openntpd.

Using wicd

These instructions require wicd 1.7.0 or later, which is available in the standard Arch repository. You will also need write access to /etc/wicd/scripts.

Note: Remember to make these two scripts executable using chmod

Make one shell script inside /etc/wicd/scripts/postconnect/ with the following:

/etc/rc.d/openntpd start

Similarly, make another shell script inside /etc/wicd/scripts/predisconnect/ with the following:

/etc/rc.d/openntpd stop

Using dhclient hooks

Another possibility is to use dhclient hooks to start and stop openntpd. When dhclient detects a change in state it will run the following scripts:

  • /etc/dhclient-enter-hooks
  • /etc/dhclient-exit-hooks

The following example uses /etc/dhclient-exit-hooks to start and stop openntpd depending on dhcp status:

[ "$interface" != "eth0" ] && exit 0

if $if_up; then
    pgrep ntpd &> /dev/null || /etc/rc.d/openntpd start
elif $if_down; then
    pgrep ntpd &> /dev/null && /etc/rc.d/openntpd stop

See dhclient-script(8)

Using dhcpcd hooks


See dhcpcd-run-hooks(8)


Error adjusting time

If you find your time set incorrectly and in log you see:

openntpd adjtime failed: Invalid argument


ntpd -s -d

This is also how you would manually sync your system.

Increasing time shift

Starting openntpd in the background could lead to synchronization errors between the actual time and the time stored on your computer. If you recognize an increasing time difference between your desktop clock and the actual time, try to start the openntpd daemon normal and not in the background.

Tango-view-refresh-red.pngThis article or section is out of date.Tango-view-refresh-red.png

Reason: rc.d references. Needs update to Systemd. (Discuss in Talk:OpenNTPD#)

Initialization Failure

Openntpd may fail to initialize properly if it is started before the network is fully configured. In some cases you may want to remove openntpd from the DAEMONS array in /etc/rc.conf and add the following line to /etc/rc.local:

(sleep 300 && /etc/rc.d/openntpd start) &
Note: This method is an alternative to the four methods listed above. The other three methods are preferred and work better. Use this as a last resort.

This will wait 5 minutes before starting openntpd, which should give the system sufficient time to set up the network properly. If your network settings change often, you may also consider restarting the daemon regularly with cron.

See also

External links