- The Preboot eXecution Environment (PXE, also known as Pre-Execution Environment; sometimes pronounced "pixie") is an environment to boot computers using a network interface independently of data storage devices (like hard disks) or installed operating systems.
In this guide, PXE is used to boot the installation media with an appropriate option-rom that supports PXE on the target. This works well when you already have a server set up.
Get the latest official install media from download page.
Next mount the image:
# mkdir -p /mnt/archiso # mount -o loop,ro archlinux-2017.12.01-x86_64.iso /mnt/archiso
Arch currently only supports BIOS-style PXE booting. See FS#50188 for more information.
Bring up your wired NIC, and assign it an address appropriately.
# ip link set eth0 up # ip addr add 192.168.0.1/24 dev eth0
DHCP + TFTP
You will need both a DHCP and TFTP server to configure networking on the install target and to facilitate the transfer of files between the PXE server and client; dnsmasq does both, and is extremely easy to set up.
Install the package.
port=0 interface=eth0 bind-interfaces dhcp-range=192.168.0.50,192.168.0.150,12h dhcp-boot=/arch/boot/syslinux/lpxelinux.0 dhcp-option-force=209,boot/syslinux/archiso.cfg dhcp-option-force=210,/arch/ dhcp-option-force=66,192.168.0.1 enable-tftp tftp-root=/mnt/archiso
Thanks to recent changes in archiso, it is now possible to boot from HTTP (
archiso_pxe_http initcpio hook) or NFS (
archiso_pxe_nfs initcpio hook); among all alternatives, darkhttpd is by far the most trivial to setup (and the lightest-weight).
First, install the package.
Then start darkhttpd using our
/mnt/archiso as the document root:
# darkhttpd /mnt/archiso
darkhttpd/1.8, copyright (c) 2003-2011 Emil Mikulic. listening on: http://0.0.0.0:80/
Note that it is important that the server is running on port
80. If you start darkhttpd without root access it will default to
8080. The client will try to access port 80 and the boot will fail.
For this portion you will need to figure out how to tell the client to attempt a PXE boot; in the corner of the screen along with the normal post messages, usually there will be some hint on which key to press to try PXE booting first. On an IBM x3650
F12 brings up a boot menu, the first option of which is Network; on a Dell PE 1950/2950 pressing
F12 initiates PXE booting directly.
Looking at journald on the PXE server will provide some additional insight to what exactly is going on during the early stages of the PXE boot process:
# journalctl -u dnsmasq.service -f
dnsmasq-dhcp: DHCPDISCOVER(eth1) 00:1a:64:6a:a2:4d dnsmasq-dhcp: DHCPOFFER(eth1) 192.168.0.110 00:1a:64:6a:a2:4d dnsmasq-dhcp: DHCPREQUEST(eth1) 192.168.0.110 00:1a:64:6a:a2:4d dnsmasq-dhcp: DHCPACK(eth1) 192.168.0.110 00:1a:64:6a:a2:4d dnsmasq-tftp: sent /mnt/archiso/arch/boot/syslinux/pxelinux.0 to 192.168.0.110 dnsmasq-tftp: sent /mnt/archiso/arch/boot/syslinux/archiso.cfg to 192.168.0.110 dnsmasq-tftp: sent /mnt/archiso/arch/boot/syslinux/whichsys.c32 to 192.168.0.110 dnsmasq-tftp: sent /mnt/archiso/arch/boot/syslinux/archiso_pxe_choose.cfg to 192.168.0.110 dnsmasq-tftp: sent /mnt/archiso/arch/boot/syslinux/ifcpu64.c32 to 192.168.0.110 dnsmasq-tftp: sent /mnt/archiso/arch/boot/syslinux/archiso_pxe_both_inc.cfg to 192.168.0.110 dnsmasq-tftp: sent /mnt/archiso/arch/boot/syslinux/archiso_head.cfg to 192.168.0.110 dnsmasq-tftp: sent /mnt/archiso/arch/boot/syslinux/archiso_pxe32.cfg to 192.168.0.110 dnsmasq-tftp: sent /mnt/archiso/arch/boot/syslinux/archiso_pxe64.cfg to 192.168.0.110 dnsmasq-tftp: sent /mnt/archiso/arch/boot/syslinux/archiso_tail.cfg to 192.168.0.110 dnsmasq-tftp: sent /mnt/archiso/arch/boot/syslinux/vesamenu.c32 to 192.168.0.110 dnsmasq-tftp: sent /mnt/archiso/arch/boot/syslinux/splash.png to 192.168.0.110
After you load
archiso.cfg via TFTP, you will (hopefully) be presented with a syslinux boot menu with several options, where you can select Boot Arch Linux (x86_64) (HTTP).
Next the kernel and initramfs (appropriate for the architecture you selected) will be transferred, again via TFTP:
dnsmasq-tftp: sent /mnt/archiso/arch/boot/x86_64/vmlinuz to 192.168.0.110 dnsmasq-tftp: sent /mnt/archiso/arch/boot/x86_64/archiso.img to 192.168.0.110
If all goes well, you should then see activity on darkhttpd coming from the PXE-target; at this point the kernel would be loaded on the PXE-target, and in init:
1348347586 192.168.0.110 "GET /arch/aitab" 200 678 "" "curl/7.27.0" 1348347587 192.168.0.110 "GET /arch/x86_64/root-image.fs.sfs" 200 107860206 "" "curl/7.27.0" 1348347588 192.168.0.110 "GET /arch/x86_64/usr-lib-modules.fs.sfs" 200 36819181 "" "curl/7.27.0" 1348347588 192.168.0.110 "GET /arch/any/usr-share.fs.sfs" 200 63693037 "" "curl/7.27.0"
After the root filesystem is downloaded via HTTP, you will eventually end up at the normal live system root zsh prompt.
Unless you want all traffic to be routed through your PXE server (which will not work anyway unless you set it up properly), you will want to stop
dnsmasq.service and get a new lease on the install target, as appropriate for your network layout.
You can also kill darkhttpd; the target has already downloaded the root filesystem, so it is no longer needed. While you are at it, you can also unmount the installation image:
# umount /mnt/archiso
At this point you can follow the Installation guide.
As implied in the syslinux menu, there are several other alternatives:
You will need to set up an NFS server with an export at the root of your mounted installation media, which would be
/mnt/archiso if you followed #Preparation. After setting up the server, add the following line to your
If the server was already running, re-export the filesystems with
exportfs -r -a -v.
The default settings in the installer expect to find the NFS at
/run/archiso/bootmnt, so you will need to edit the boot options. To do this, press Tab on the appropriate boot menu choice and edit the
archiso_nfs_srv option accordingly:
Alternatively, you can use
/run/archiso/bootmnt for the entire process.
After the kernel loads, the Arch bootstrap image will copy the root filesystem via NFS to the booting host. This can take a little while. Once this completes, you should have a running system.
Install the package and configure it:
[generic] [archiso] readonly = true exportname = /srv/archlinux-2017.12.01-x86_64.iso
Existing PXE Server
If you have an existing PXE server with a PXELINUX system setup (e.g. a combination of DHCP and TFTP), you can add the following menu items to your
pxelinux.cfg file in order to boot Arch via your preferred method:
LABEL 2 MENU LABEL Arch Linux x86_64 LINUX /path/to/extracted/Arch/ISO/arch/boot/x86_64/vmlinuz INITRD /path/to/extracted/Arch/ISO/arch/boot/intel_ucode.img,/path/to/extracted/Arch/ISO/arch/boot/x86_64/archiso.img APPEND archisobasedir=arch archiso_http_srv=http://httpserver/path/to/extracted/Arch/ISO/ ip=:: SYSAPPEND 2 TEXT HELP Arch Linux 2017.12.01 x86_64 ENDTEXT
You can replace
archiso_nfs_srv for NFS or
archiso_nbd_srv for NBD. Adding the
ip= instruction is necessary to instruct the kernel to bring up the network interface before it attempts to mount the installation medium over the network. See README.bootparams for available boot parameters.
DHCP interface rename bug
FS#36749 causes default predictable network interface renaming to fail and then dhcp client to fail because of it. A workaround is to add the kernel boot parameter
net.ifnames=0 to disable predictable interface names.
Low memory systems
copytoram initramfs option can be used to control whether the root filesystem should be copied to ram in its entirety in early-boot.
It highly recommended to leave this option alone, and should only be disabled if entirely necessary (systems with less than ~256MB physical memory). Append
copytoram=n to your kernel line if you wish to do so.
archiso_pxe_httpare mutually exclusive.