Persistent block device naming

From ArchWiki
Revision as of 14:59, 16 March 2019 by Nl6720 (talk | contribs) (Persistent naming methods: flag with Template:Expansion, subsections could use `blkid -o value` examples)
Jump to navigation Jump to search

This article describes how to use persistent names for your block devices. This has been made possible by the introduction of udev and has some advantages over bus-based naming. If your machine has more than one SATA, SCSI or IDE disk controller, the order in which their corresponding device nodes are added is arbitrary. This may result in device names like /dev/sda and /dev/sdb switching around on each boot, culminating in an unbootable system, kernel panic, or a block device disappearing. Persistent naming solves these issues.

  • Persistent naming has limits that are out-of-scope in this article. For example, while mkinitcpio may support a method, systemd may impose its own limits (e.g. FS#42884) on naming it can process during boot.
  • This article is not relevant for LVM logical volumes as the /dev/VolumeGroupName/LogicalVolumeName device paths are persistent.

Persistent naming methods

Tango-view-fullscreen.pngThis article or section needs expansion.Tango-view-fullscreen.png

Reason: Add blkid commands to subsections showing how to retrieve only the UUID/LABEL/PARTUUID/PARTLABEL of a device. (Discuss in Talk:Persistent block device naming#)

There are four different schemes for persistent naming: by-label, by-uuid, by-id and by-path. For those using disks with GUID Partition Table (GPT), two additional schemes can be used by-partlabel and by-partuuid. You can also use static device names by using Udev.

The directories in /dev/disk/ are created and destroyed dynamically, depending on whether you there are devices in them.

Note: Beware that Disk cloning creates two different disks with the same name.

The following sections describes what the different persistent naming methods are and how they are used.

The lsblk command can be used for viewing graphically the first persistent schemes:

$ lsblk -f
NAME        FSTYPE LABEL  UUID                                 MOUNTPOINT
├─sda1      vfat          CBB6-24F2                            /boot
├─sda2      ext4   System 0a3407de-014b-458b-b5c1-848e92a327a3 /
├─sda3      ext4   Data   b411dc99-f0a0-4c87-9e05-184977be8539 /home
└─sda4      swap          f9fe0b69-a280-415d-a03a-a32752370dee [SWAP]
└─mmcblk0p1 vfat          F4CA-5D75

For those using GPT, use the blkid command instead. The latter is more convenient for scripts, but more difficult to read.

$ blkid
/dev/sda1: UUID="CBB6-24F2" TYPE="vfat" PARTLABEL="EFI system partition" PARTUUID="d0d0d110-0a71-4ed6-936a-304969ea36af" 
/dev/sda2: LABEL="System" UUID="0a3407de-014b-458b-b5c1-848e92a327a3" TYPE="ext4" PARTLABEL="GNU/Linux" PARTUUID="98a81274-10f7-40db-872a-03df048df366" 
/dev/sda3: LABEL="Data" UUID="b411dc99-f0a0-4c87-9e05-184977be8539" TYPE="ext4" PARTLABEL="Home" PARTUUID="7280201c-fc5d-40f2-a9b2-466611d3d49e" 
/dev/sda4: UUID="f9fe0b69-a280-415d-a03a-a32752370dee" TYPE="swap" PARTLABEL="Swap" PARTUUID="039b6c1c-7553-4455-9537-1befbc9fbc5b"
/dev/mmcblk0: PTUUID="0003e1e5" PTTYPE="dos"
/dev/mmcblk0p1: UUID="F4CA-5D75" TYPE="vfat" PARTUUID="0003e1e5-01"


Almost every filesystem type can have a label. All your volumes that have one are listed in the /dev/disk/by-label directory.

$ ls -l /dev/disk/by-label
total 0
lrwxrwxrwx 1 root root 10 May 27 23:31 Data -> ../../sda3
lrwxrwxrwx 1 root root 10 May 27 23:31 System -> ../../sda2

Most file systems support setting the label upon file system creation, see the man page of the relevant mkfs.* utility. For some file systems it is also possible to change the labels. Following are some methods for changing labels on common file systems:

swaplabel -L "new label" /dev/XXX using util-linux
e2label /dev/XXX "new label" using e2fsprogs
btrfs filesystem label /dev/XXX "new label" using btrfs-progs
reiserfstune -l "new label" /dev/XXX using reiserfsprogs
jfs_tune -L "new label" /dev/XXX using jfsutils
xfs_admin -L "new label" /dev/XXX using xfsprogs
fatlabel /dev/XXX "new label" using dosfstools
mlabel -i /dev/XXX ::"new label" using mtools
exfatlabel /dev/XXX "new label" using exfat-utils
ntfslabel /dev/XXX "new label" using ntfs-3g
udflabel /dev/XXX "new label" using udftools
crypto_LUKS (LUKS2 only) 
cryptsetup config --label="new label" /dev/XXX using cryptsetup
  • The file system must not be mounted to change its label. For the root file system this can be accomplished by booting from another volume.
  • Labels have to be unambiguous to prevent any possible conflicts.
  • Labels can be up to 16 characters long.
  • Since the label is a property of the filesystem, it is not suitable for addressing a single RAID device persistently.
  • When using encrypted containers with dm-crypt, the labels of filesystems inside of containers are not available while the container is locked/encrypted.


UUID is a mechanism to give each filesystem a unique identifier. These identifiers are generated by filesystem utilities (e.g. mkfs.*) when the device gets formatted and are designed so that collisions are unlikely. All GNU/Linux filesystems (including swap and LUKS headers of raw encrypted devices) support UUID. FAT, exFAT and NTFS filesystems do not support UUID, but are still listed in /dev/disk/by-uuid/ with a shorter UID (unique identifier):

$ ls -l /dev/disk/by-uuid/
total 0
lrwxrwxrwx 1 root root 10 May 27 23:31 0a3407de-014b-458b-b5c1-848e92a327a3 -> ../../sda2
lrwxrwxrwx 1 root root 10 May 27 23:31 b411dc99-f0a0-4c87-9e05-184977be8539 -> ../../sda3
lrwxrwxrwx 1 root root 10 May 27 23:31 CBB6-24F2 -> ../../sda1
lrwxrwxrwx 1 root root 10 May 27 23:31 f9fe0b69-a280-415d-a03a-a32752370dee -> ../../sda4
lrwxrwxrwx 1 root root 10 May 27 23:31 F4CA-5D75 -> ../../mmcblk0p1

The advantage of using the UUID method is that it is much less likely that name collisions occur than with labels. Further, it is generated automatically on creation of the filesystem. It will, for example, stay unique even if the device is plugged into another system (which may perhaps have a device with the same label).

The disadvantage is that UUIDs make long code lines hard to read and break formatting in many configuration files (e.g. fstab or crypttab). Also every time a volume is reformatted a new UUID is generated and configuration files have to get manually adjusted.

Tip: In case your swap does not have an UUID assigned, you will need to reset it using the mkswap utility.

by-id and by-path

by-id creates a unique name depending on the hardware serial number, by-path depending on the shortest physical path (according to sysfs). Both contain strings to indicate which subsystem they belong to (i.e. pci- for by-path, and ata- for by-id), so they are linked to the hardware controlling the device. This implies different levels of persistence: the by-path will already change when the device is plugged into a different port of the controller, the by-id will change when the device is plugged into a port of a hardware controller subject to another subsystem. [1] Thus, both are not suitable to achieve persistent naming tolerant to hardware changes.

However, both provide important information to find a particular device in a large hardware infrastructure. For example, if you do not manually assign persistent labels (by-label or by-partlabel) and keep a directory with hardware port usage, by-id and by-path can be used to find a particular device.[2] [3]

by-id also creates World Wide Name links of storage devices that support it. Unlike other by-id links, WWNs are fully persistent and will not change depending on the used subsystem.

$ ls -l /dev/disk/by-id/
total 0
lrwxrwxrwx 1 root root 10 May 27 23:31 ata-WDC_WD2500BEVT-22ZCT0_WD-WXE908VF0470 -> ../../sda
lrwxrwxrwx 1 root root 10 May 27 23:31 ata-WDC_WD2500BEVT-22ZCT0_WD-WXE908VF0470-part1 -> ../../sda1
lrwxrwxrwx 1 root root 10 May 27 23:31 ata-WDC_WD2500BEVT-22ZCT0_WD-WXE908VF0470-part2 -> ../../sda2
lrwxrwxrwx 1 root root 10 May 27 23:31 ata-WDC_WD2500BEVT-22ZCT0_WD-WXE908VF0470-part3 -> ../../sda3
lrwxrwxrwx 1 root root 10 May 27 23:31 ata-WDC_WD2500BEVT-22ZCT0_WD-WXE908VF0470-part4 -> ../../sda4
lrwxrwxrwx 1 root root 10 May 27 23:31 mmc-SD32G_0x0040006d -> ../../mmcblk0
lrwxrwxrwx 1 root root 10 May 27 23:31 mmc-SD32G_0x0040006d-part1 -> ../../mmcblk0p1
lrwxrwxrwx 1 root root 10 May 27 23:31 wwn-0x60015ee0000b237f -> ../../sda
lrwxrwxrwx 1 root root 10 May 27 23:31 wwn-0x60015ee0000b237f-part1 -> ../../sda1
lrwxrwxrwx 1 root root 10 May 27 23:31 wwn-0x60015ee0000b237f-part2 -> ../../sda2
lrwxrwxrwx 1 root root 10 May 27 23:31 wwn-0x60015ee0000b237f-part3 -> ../../sda3
lrwxrwxrwx 1 root root 10 May 27 23:31 wwn-0x60015ee0000b237f-part4 -> ../../sda4
$ ls -l /dev/disk/by-path/
total 0
lrwxrwxrwx 1 root root 10 May 27 23:31 pci-0000:00:1f.2-ata-1 -> ../../sda
lrwxrwxrwx 1 root root 10 May 27 23:31 pci-0000:00:1f.2-ata-1-part1 -> ../../sda1
lrwxrwxrwx 1 root root 10 May 27 23:31 pci-0000:00:1f.2-ata-1-part2 -> ../../sda2
lrwxrwxrwx 1 root root 10 May 27 23:31 pci-0000:00:1f.2-ata-1-part3 -> ../../sda3
lrwxrwxrwx 1 root root 10 May 27 23:31 pci-0000:00:1f.2-ata-1-part4 -> ../../sda4
lrwxrwxrwx 1 root root 10 May 27 23:31 pci-0000:07:00.0-platform-rtsx_pci_sdmmc.0 -> ../../mmcblk0
lrwxrwxrwx 1 root root 10 May 27 23:31 pci-0000:07:00.0-platform-rtsx_pci_sdmmc.0-part1 -> ../../mmcblk0p1


Note: This method only concerns disks with GUID Partition Table (GPT).

GPT partition labels can be defined in the header of the partition entry on GPT disks.

This method is very similar to the filesystem labels, except the partition labels do not get affected if the file system on the partition is changed.

All partitions that have partition labels are listed in the /dev/disk/by-partlabel directory.

ls -l /dev/disk/by-partlabel/
total 0
lrwxrwxrwx 1 root root 10 May 27 23:31 EFI\x20system\x20partition -> ../../sda1
lrwxrwxrwx 1 root root 10 May 27 23:31 GNU\x2fLinux -> ../../sda2
lrwxrwxrwx 1 root root 10 May 27 23:31 Home -> ../../sda3
lrwxrwxrwx 1 root root 10 May 27 23:31 Swap -> ../../sda4
  • GPT partition labels also have to be different to avoid conflicts. To change your partition label, you can use gdisk or the ncurses-based version cgdisk. Both are available from the gptfdisk package. See Partitioning#Partitioning tools.
  • According to the specification, GPT partition labels can be up to 72 characters long.


Like GPT partition labels, GPT partition UUIDs are defined in the partition entry on GPT disks.

MBR does not support partition UUIDs, but Linux[4] and software using libblkid[5] (e.g. udev[6]) are capable of generating pseudo PARTUUIDs for MBR partitions. The format is SSSSSSSS-PP, where SSSSSSSS is a zero-filled 32-bit MBR disk signature, and PP is a zero-filled partition number in hexadecimal form. Unlike a regular PARTUUID of a GPT partition, MBR's pseudo PARTUUID can change if the partition number changes.

The dynamic directory is similar to other methods and, like filesystem UUIDs, using UUIDs is preferred over labels.

ls -l /dev/disk/by-partuuid/
total 0
lrwxrwxrwx 1 root root 10 May 27 23:31 0003e1e5-01 -> ../../mmcblk0p1
lrwxrwxrwx 1 root root 10 May 27 23:31 039b6c1c-7553-4455-9537-1befbc9fbc5b -> ../../sda4
lrwxrwxrwx 1 root root 10 May 27 23:31 7280201c-fc5d-40f2-a9b2-466611d3d49e -> ../../sda3
lrwxrwxrwx 1 root root 10 May 27 23:31 98a81274-10f7-40db-872a-03df048df366 -> ../../sda2
lrwxrwxrwx 1 root root 10 May 27 23:31 d0d0d110-0a71-4ed6-936a-304969ea36af -> ../../sda1

Static device names with Udev

See udev#Setting static device names.

Using persistent naming

There are various applications that can be configured using persistent naming. Following are some examples of how to configure them.


See the main article: fstab#Identifying filesystems.

Boot managers

To use persistent names in the boot manager (boot loader), the following prerequisites must be met. On a standard installation following the installation guide both prerequisites are met.

  • You are using a mkinitcpio initial RAM disk image
  • You have udev enabled in /etc/mkinitcpio.conf

The location of the root filesystem is given by the parameter root on the kernel commandline. The kernel commandline is configured from the bootloader, see Kernel parameters#Configuration. To change to persistent device naming, only change the parameters which specify block devices, e.g. root and resume, while leaving other parameters as is. Various naming schemes are supported:

Persistent device naming using label and the LABEL= format, in this example System is the LABEL of the root file system.


Persistent device naming using UUID and the UUID= format, in this example 0a3407de-014b-458b-b5c1-848e92a327a3 is the UUID of the root file system.


Persistent device naming using disk id and the /dev path format, in this example wwn-0x60015ee0000b237f-part2 is the id of the root partition.


Persistent device naming using GPT partition UUID and the PARTUUID= format, in this example 98a81274-10f7-40db-872a-03df048df366 is the PARTUUID of the root partition.


Persistent device naming using GPT partition label and the PARTLABEL= format, in this example GNU/Linux is the PARTLABEL of the root partition.