From ArchWiki
Revision as of 17:55, 6 June 2013 by Txus.palacios (talk | contribs) (DNS Error)
Jump to: navigation, search

zh-CN:Polipo Template:Article summary start Template:Article summary text Template:Article summary heading Template:Article summary wiki Template:Article summary end

From Polipo's site:

"Polipo is a small and fast caching web proxy (a web cache, an HTTP proxy, a proxy server). While Polipo was designed to be used by one person or a small group of people, there is nothing that prevents it from being used by a larger group."

Unlike Squid, Polipo is very light on resources and simple to configure. This makes it ideal for single user systems and other uncomplicated setups. Do keep in mind; however, that this versatility comes at a cost; Polipo will increase its space usage without restriction as it is not aware of how big its disk cache grows. This perceived fault is by design, since omitting these sanity checks drastically reduces Polipo's memory usage and overall toll on the system. A practical way of restricting disk usage is by making Polipo run as its own user and employing disk quota.

The following covers installing and setting up Polipo.


Install polipo, available in the Official Repositories.

Alternatively, install the newer development branch polipo-gitAUR from the AUR instead.

Run polipo as different user (not nobody)

Polipo should run as an unprivileged user. Such a user can either be created or reused. Lets create the polipo cache folder first

# mkdir /var/cache/polipo

Now we add the new polipo group

# groupadd -r polipo

and we add the new polipo user afterwards to this group

# useradd -d /var/cache/polipo -g polipo -r -s /bin/false polipo

then we need a new polipo logfile which is assigned to the upper user and group

# touch /var/log/polipo.log
# chown -R polipo:polipo /var/log/polipo.log /var/cache/polipo

To change user running polipo daemon, we have to create another polipo.service file

# touch /etc/systemd/system/polipo.service

Copy the following code section to the new /etc/systemd/system/polipo.service file

.include /usr/lib/systemd/system/polipo.service

To make sure all files and folders are created before you start Polipo as a designated user. Restart Polipo and check its logfile.

# systemctl restart polipo
# tail /var/log/polipo.log

If everything went well you should read something like this

 Established listening socket on port 8123.

Also check, if polipo is running as polipo user:

# ps aux | grep polipo

Stop the polipo daemon

# systemctl stop polipo

Starting the daemon

To start the polipo daemon:

# systemctl start polipo

To start it automatically at boot:

# systemctl enable polipo

Multiple instances

Polipo can also run without super user privileges. To do so, first copy /etc/polipo/config.sample to a suitable directory:

$ cp /etc/polipo/config.sample ~/.poliporc

Edit it so that it points at a writable location, instead of /var/cache/polipo:

# Uncomment this if you want to put the on-disk cache in a
# non-standard location:
diskCacheRoot = "~/.polipo-cache/"

Create the cache directory:

$ mkdir ~/.polipo-cache

Finally, launch Polipo with the new configuration:

$ polipo -c ~/.poliporc


Management is mostly performed in /etc/polipo/config. Most users can opt for using the sample configuration file, which is sufficient for most situations and well documented.

# cd /etc/polipo; cp config.sample config

One element of configuration that warrants mentioning is polipo's default behavior of blocking outbound connections by port. There are two variables in polipo's config file that control allowed outbound ports. allowedPorts specifies ports for outbound HTTP connections. It defaults to 80-100 and 1024-65535. tunnelAllowedPorts specifies ports polipo will allow tunnel traffic to as well as HTTPS traffic. By default it is much more restricted: "It defaults to allowing ssh, HTTP, https, rsync, IMAP, imaps, POP, pops, Jabber, CVS and Git traffic."

If you see a "403 Forbidden Port" error message from polipo when attempting to browse to a host:port, you need to configure polipo to accept traffic to more ports for either HTTP or HTTPS. To set them wide open, add the following to /etc/polipo/config:

allowedPorts = 1-65535
tunnelAllowedPorts = 1-65535

Unlike other proxies, Polipo needs to be restarted after alterations.


Set the browser so that it uses localhost:8123 for proxying. Be sure to disable the browser's disk cache to avoid redundant IO operations and bad performance.


Note: According to the Polipo FAQ on "intercepting proxy" this is not possible/supported!
Note: this requires to run Polipo as its own user.

Instead of manually configuring each browser or other utilities that might benefit from Polipo's caching, one can also use iptables to route traffic through polipo.

After installing iptables, add the appropiate rules to /etc/iptables/iptables.rules:

-A OUTPUT -p tcp --dport 80 -m owner ! --uid-owner polipo -j ACCEPT
-A OUTPUT -p tcp --dport 80 -j REDIRECT --to-ports 8123

This routes HTTP traffic through Polipo. Remove all proxy settings from browsers, if any, and restart iptables.


Privoxy is a proxy useful for intercepting advertisement and other undesirables.

According to Polipo's developer, in order to get the privacy enhancements of Privoxy and much (but not all) of the performance of Polipo, one should place Polipo upstream of Privoxy.

In other words:

  • point the browser at Privoxy: localhost:8118
  • and direct Privoxy traffic to Polipo: forward / localhost:8123 in the Privoxy configuration file.


Tor is an anonymizing proxy network.

To use Polipo with Tor, uncomment or include the following in /etc/polipo/config:

socksParentProxy = localhost:9050
socksProxyType = socks5


DansGuardian is a web content filter. The only difference to using DansGuardian with Polipo (rather than squid or tinyproxy) is that in dansguardian.conf the proxyport needs to be set to polipo's 8123:

# the port DansGuardian connects to proxy on
proxyport = 8123


DNS Error

If the network is started in background there could be a error like this in the Polipo log file:

Couldn't send DNS query: Connection refused
Falling back on gethostbyname.
Getaddrinfo failed: Temporary name server failure
Host ***.com lookup failed: Getaddrinfo failed: Temporary name server failure (131072).

This error occurs because in background mode the network hasn't initialised before Polipo wants to connect to the DNS server (especially using DHCP). Solving this error is possible on three ways:

  • Do not start the net-profiles in background mode (probably not wanted).
  • Set dnsNameServer manually on the wanted DNS server.
  • Or add sleep 10 (or more, it depends) near the beginning of the Polipo daemon script /etc/rc.d/polipo in the start section. This will make Polipo start after the network has initialised.

See this thread for more information on this topic.

See also