Difference between revisions of "Power saving"

From ArchWiki
Jump to: navigation, search
m (Custom settings)
m (Wireless power saving)
Line 98: Line 98:
{{Note|This should be combined with [[udev#Network device|static naming]] of devices, the eth* names are not static.}}
{{Note|This should be combined with [[udev#Network device|static naming]] of devices, the eth* names are not static.}}
{{Note|This method does not seem to work at the moment.}}
{{hc|/etc/udev/rules.d/wlan0_power_save.rules|2=ACTION=="add", SUBSYSTEM=="net", KERNEL=="wifi0" RUN+="/usr/sbin/iw dev wifi0 set power_save on"}}
{{hc|/etc/udev/rules.d/wlan0_power_save.rules|2=ACTION=="add", SUBSYSTEM=="net", KERNEL=="wifi0" RUN+="/usr/sbin/iw dev wifi0 set power_save on"}}

Revision as of 07:54, 3 April 2013

This article covers the configuration needed to turn on power saving features. Almost all of the features listed here are worth using whether or not the computer is on AC or battery power. Most have negligible performance impact and are just not enabled by default because of commonly broken hardware/drivers. Reducing power usage means reducing heat, which can even lead to higher performance on a modern Intel or AMD CPU, thanks to dynamic overclocking.

Ready to run scripts

There are already a couple of scripts and tools which make use of the various settings described in the next section. These are notably:

If you do not want to take care of the settings by yourself it is recommended to use these tools. But be aware of running only one of these tools to avoid possible conflicts as they all work more or less similar.

Custom settings

If you would like to create your own scripts and power saving settings such as by udev rules you can take the following settings as a reference.


By default, audio power saving is turned off by most drivers. It can be enabled by setting the power_save parameter to a time (in seconds) to go in idle.

Note: Toggling the audio card's power state can cause a popping sound or noticeable latency on some broken hardware.
options snd_hda_intel power_save=1
options snd_ac97_codec power_save=1

Active State Power Management

To verify that ASPM is enabled:

$ cat /sys/module/pcie_aspm/parameters/policy
[default] performance powersave

Either [default] or [powersave] means you do not need to force it on.

Otherwise, it's either unsupported/broken on your hardware, or has to be forced on with pcie_aspm=force on the kernel line.

Warning: Forcing on ASPM can cause a freeze/panic, so make sure you have a way to undo the option if it doesn't work.
Warning: On systems that don't support it forcing on ASPM can even increase power consumption.


When system starts, screen backlight is set to maximum by default. This can be fixed by specifying backlight level in the following udev rule:

SUBSYSTEM=="backlight", ACTION=="add", KERNEL=="acpi_video0", ATTR{brightness}="1"


Tango-view-fullscreen.pngThis article or section needs expansion.Tango-view-fullscreen.png

Reason: The device should likely be disabled with hciconfig first. (Discuss in Talk:Power saving#)
Blacklist the hci_usb module if the driver is loaded automatically.

Alternatively, blacklist the btusb and bluetooth modules.

Another variant is to rfkill it:

# rfkill block bluetooth

Or with udev rule:

SUBSYSTEM=="rfkill", ATTR{type}=="bluetooth", ATTR{state}="0"


If you won't use integrated web camera then blacklist the uvcvideo module.

Disabling NMI watchdog

The NMI watchdog is a debugging feature to catch hardware hangs and cause a kernel panic. On some systems it can generate a lot of interrupts, causing a noticeable increase in power usage.

kernel.nmi_watchdog = 0

or add nmi_watchdog=0 as a kernel parameter to disable it completely from early boot.

Disabling Wake-on-LAN

Wake-on-LAN can be a useful feature, but if you're not making use of it then it's simply draining extra power waiting for a magic packet while in suspend.

Disabling for all Ethernet interfaces:

ACTION=="add", SUBSYSTEM=="net", KERNEL=="eth*" RUN+="/usr/sbin/ethtool -s %k wol d"

You can use multiple names in the matches; for example, KERNEL=="lan0|eth*"

Note: This should be combined with static naming of devices, the eth* names are not static.

PCI Runtime Power Management

ACTION=="add", SUBSYSTEM=="pci", ATTR{power/control}="auto"

Wireless power saving

Enabling for a specific interface:

Note: This should be combined with static naming of devices, the eth* names are not static.
Note: This method does not seem to work at the moment.
ACTION=="add", SUBSYSTEM=="net", KERNEL=="wifi0" RUN+="/usr/sbin/iw dev wifi0 set power_save on"

Enabling for all interfaces:

ACTION=="add", SUBSYSTEM=="net", KERNEL=="wlan*" RUN+="/usr/sbin/iw dev %k set power_save on"

Writeback Time

Increasing the VM dirty writeback time can help to aggregate I/O together - reducing disk writes, and decreasing power usage:

vm.dirty_writeback_centisecs = 1500

To do the same for journal commits with ext4 and some other filesystems, use commit=15 as a parameter in fstab or with the rootflags kernel parameter.

Laptop Mode

vm.laptop_mode = 5

SATA Active Link Powermanagement

Note: This adds latency when accessing a drive that has been idle, so it's one of the few settings that may be worth toggling based on whether you're on AC power.
SUBSYSTEM=="scsi_host", KERNEL=="host*", ATTR{link_power_management_policy}="min_power"

USB Autosuspend

To enable USB autosuspend after 2 seconds of inactivity:

ACTION=="add", SUBSYSTEM=="usb", TEST=="power/control" ATTR{power/control}="auto"
ACTION=="add", SUBSYSTEM=="usb", TEST=="power/autosuspend" ATTR{power/autosuspend}="2"

Device Power Management

Tango-inaccurate.pngThe factual accuracy of this article or section is disputed.Tango-inaccurate.png

Reason: Should be done with a udev rule. (Discuss in Talk:Power saving#)
echo auto | tee /sys/bus/i2c/devices/*/power/control > /dev/null
echo auto | tee /sys/bus/spi/devices/*/power/control > /dev/null

View Power Setings

This function shows various power settings. Note you either must be root or you must have sudo.

function aa_power_settings ()
  sudo bash -c '
    for i in `find /sys/devices -name "bMaxPower"`;
        for ii in `find $i -type f`;
            bd=`dirname $ii`;
            busnum=`cat $bd/busnum`;
            devnum=`cat $bd/devnum`;
            title=`lsusb -s $busnum:$devnum`;
            echo -e "\n\n+++ $title\n  -$bd\n  -$ii";
            for ff in `find $bd/power -type f ! -empty 2>/dev/null`;
                v=`cat $ff 2>/dev/null|tr -d "\n"`;
                [[ ${#v} -gt 0 ]] && echo -e " `basename $ff`=$v";
            done | sort -g;
    echo -e "\n\n\n+++ Kernel Modules\n";
    for m in `command lspci -k|sed -n "/in use:/s,^.*: ,,p"|sort -u`;
        echo "+ $m";
        systool -v -m $m 2> /dev/null | sed -n "/Parameters:/,/^$/p";

See also