Difference between revisions of "Powernowd"

From ArchWiki
Jump to: navigation, search
Line 1: Line 1:
 
[[Category:Power management]]
 
[[Category:Power management]]
[[Category:Daemons and system services]]
 
 
[http://www.deater.net/john/powernowd.html Powernowd] is a very simple [[daemon]] that will adjust the speed of your CPU depending on system load.
 
[http://www.deater.net/john/powernowd.html Powernowd] is a very simple [[daemon]] that will adjust the speed of your CPU depending on system load.
  

Revision as of 06:16, 16 December 2012

Powernowd is a very simple daemon that will adjust the speed of your CPU depending on system load.

Warning: This software, while may still work fine on modern kernels, is no longer in active development and likely less efficent than using cpufreq's ondemand governor. Using the cpufreq-ondemand kernel module is preferable over powernowd. See CPU Frequency Scaling for more information on using the cpufreq-ondemand kernel module.
Note: Don't let the name fool you. Despite being named after AMD's PowerNow! technology, it should work on any system supported by the cpufreq-userspace governor.

Obsolescent Note

Although elegant, this software is actually obsolete. One can achieve the same effect with the cpufreq-ondemand kernel module and adjusting the ondemand governor's threshold. See CPU Frequency Scaling for more information.

Features

  • One, simple heuristic to determine CPU load: "user + sys" time.
  • Ignore "niced" programs (setiathome, itself, etc). In my mind this is consistent with what is meant when someone 'nice's a program to begin with. (configurable in v0.85+)
  • Designed for CPU's that support more then two speed states, but works well with anything.
  • Very fast, low overhead /proc/stat gathering (method stolen from procps).
  • Supports SMP
  • Will automatically switch to 'userspace' governor.
  • Care taken to make the code non-root exploitable (but please audit for yourself first!)
  • Frequency step size is configurable (default to 100MHz/step)
  • 4 different behavioral modes to choose from (SINE, AGGRESSIVE, PASSIVE, LEAPS), which determine the behavior when the load changes. Configurable from the command line.
  • Written in C for speed and simplicity.
  • Logging to stdout or syslog
  • Configurable Polling frequency in milliseconds (defaults to 1s)
  • Configurable highwater/lowwater marks for CPU usage. (defaults 80/20%)

Installation

Prerequisites

In order for frequency scaling to work properly, you will need to load the appropriate frequency driver for your processor as well as the cpufreq-userspace governor. See CPU Frequency Scaling.

Installation of Powernowd

This package is available in the AUR: powernowdAUR. If you haven't used the AUR before, you may want to check out AUR_User_Guidelines at your leisure as there are a wealth of great software there for you, and building the package on your machine is trivial. Install 'powernowd', then start the daemon:

# /etc/rc.d/powernowd start

To have it automatically load at startup, add powernowd to your DAEMONS array in /etc/rc.conf.

DAEMONS=( ... powernowd ... )

Basic Configuration

The only configuration you need is to set the highwater/lowwater marks for CPU usage. Basically this means when the CPU usage is >=highwater mark, then powernowd will use your highest CPU multiplier (i.e. full power); when the CPU usage <=lowwater mark, then powernowd will use your lowest CPU multiplier. The defaults are 80/20% but I find that adjusting them down gives me a more responsive system. I use 15/5% for example. To do so edit your /etc/conf.d/powernowd inserting the following line:

OPTIONS="-q -u 15 -l 5"

Restart the daemon and enjoy

# /etc/rc.d/powernowd restart

There are other options you can set such as modes of operation (sine, passive, aggressive, leaps), polling frequency, number of threads per core, etc. To see what is available, invoke powernowd with the -h switch

$ powernowd -h
PowerNow Daemon v1.00, (c) 2003-2008 John Clemens
Daemon to control the speed and voltage of cpus.

This is a simple client to the CPUFreq driver, and uses
linux kernel v2.5+ sysfs interface.  You need a supported
cpu, and a kernel that supports sysfs to run this daemon.

Available Options:
 	-h	Print this help message 
	-d	Don't detach from terminal (default is to
		detach and run in the background)
	-v	Increase output verbosity, can be used more than once.
	-q	Quiet mode, only emergency output.
	-n	Include 'nice'd processes in calculations
	-m #	Modes of operation, can be 0, 1, 2, or 3:
		0 = SINE, 1 = AGGRESSIVE (default),
		2 = PASSIVE, 3 = LEAPS
	-s #	Frequency step in kHz (default = 100000)
	-p #	Polling frequency in msecs (default = 1000)
	-c #	Specify number of threads per power-managed core
	-u #	CPU usage upper limit percentage [0 .. 100, default 80]
	-l #    CPU usage lower limit percentage [0 .. 100, default 20]