ppp (Paul's PPP Package) is an open source package which implements the point-to-point protocol (PPP) on Linux and Solaris systems. It is implemented as single pppd daemon and acts as backend for , and netcfg. 3G, L2TP and PPPoE connections are internally based on PPP protocol and therefore can be managed by .
Make sure that your kernel is compiled with PPPoE support (present in default kernel):
$ zgrep CONFIG_PPPOE /proc/config.gz
Create the connection configuration file:
plugin rp-pppoe.so # rp_pppoe_ac 'your ac name' # rp_pppoe_service 'your service name' # network interface eth0 # login name name "someloginname" usepeerdns persist # Uncomment this if you want to enable dial on demand #demand #idle 180 defaultroute hide-password noauth
If you want usepeerdns to work, you have to edit your
/etc/ppp/ip-up and add a command that copies
Put a line like this in
/etc/ppp/chap-secrets as required by the authentication method used by your ISP. It's OK to write these two files at the same time, pppd will automatically use the appropriate one.
someloginname * yourpassword
You can now start the link using the command
# pppd call your_provider
Alternatively, you can use this
# pon your_provider
To see whether your pppoe connection is started correctly, check
/var/log/errors.log first and then check
/var/log/everything.log. On a successful connection, you should see something like the following in the everything.log:
# tail /var/log/everything.log
Aug 9 00:18:08 localhost pppd: Using interface ppp0 Aug 9 00:18:08 localhost pppd: Connect: ppp0 <--> eth0 Aug 9 00:18:11 localhost pppd: CHAP authentication succeeded Aug 9 00:18:11 localhost pppd: CHAP authentication succeeded Aug 9 00:18:11 localhost pppd: peer from calling number 00:06:29:AF:4F:E0 authorized Aug 9 00:18:11 localhost pppd: Cannot determine ethernet address for proxy ARP Aug 9 00:18:11 localhost pppd: local IP address 10.6.2.137 Aug 9 00:18:11 localhost pppd: remote IP address 10.6.1.1 Aug 9 00:18:11 localhost pppd: primary DNS address 10.6.1.1 Aug 9 00:18:11 localhost pppd: secondary DNS address 184.108.40.206
By default the configuration in
/etc/ppp/peers/provider is treated as the default, so if you want to make "your_provider" the default, you can create a link like this
# ln -s /etc/ppp/peers/your_provider /etc/ppp/peers/provider
Now you can start the link by simply running
To close a connection, use this
# poff your_provider
Starting pppd with Arch
- The init script
/etc/rc.d/pppcalls the default ppp provider (
/etc/ppp/peers/provider), so make sure you have the right configuration file there, otherwhise you could create a symlink to the desired provider as explained before.
- Make sure ppp module is loaded. If ppp support is compiled as a module, you have to load the
ppp_genericmodule. In this case, add this to
MODULES=(... ppp-generic ...)
- Add ppp to
/etc/rc.conf, and make sure that you also have the network daemon listed:
DAEMONS=(... network ... ppp ...)
- Also make sure that you have the correct interface declared in the networking section of
Do an auto redial
pppd is running, you can force a connection reset by sending the
SIGHUP signal to the process
# export PPPD_PID=$(pidof pppd) # kill -s HUP $PPPD_PID
And you have redialed the connection.
Make sure you have
persist option enabled in your
ISP auto-disconnect after 24h
If you use a flat-rate always-on connection on a computer, some providers restart your connection after 24h. That makes sure that the IP is rotated every 24h. To compensate, you can use an dynamic DNS service in combination with
inadyn (available on AUR) to compensate for the rotating IP address. But to avoid disconnects when you don't need it, you might try to restart the connection using a cron job at a time of day you know no one will be using the connection (ex. 4 AM).
As root, do the following:
Create a bash script similar to this and give it a name (ex
#!/bin/bash message="Restarting the PPP connection @:" $(date) pppd_id=$(pidof pppd) kill -s HUP $pppd_id wall $message
Give it execute permissions and put it on a path visible to root.
Then create a cron job using
crontab -e. Check that your
EDITOR env variable is set if the command fails. So add anywhere in the file,
0 4 * * * /bin/bash /root/pppd_redial.sh
Save and exit. Your PPPoE connection will now restart every day at 4AM.
If you have a preconfigured default route before the pppd is started, the default route is kept, so take a look in
/var/log/errors.log and if you have something like:
pppd[nnnn]: not replacing existing default route via xx.xx.xx.xx
and xx.xx.xx.xx is not the correct route for you
- Create a new script
$ chmod +x
with this content:
#!/bin/sh /sbin/route del default
- Restart pppd:
$ /etc/rc.d/ppp restart
Masquering seems to be working fine but some sites don't work.
The MTU under pppoe is 1492 bytes. Most sites use an MTU of 1500. So your connection sends an ICMP 3:4 (fragmentation needed) packet, asking for a smaller MTU, but some sites have their firewall blocking that.
Using PMTU clamping can solve that:
iptables -I FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu
pppd cannot load kernel module ppp_generic
Symptom: When starting PPTP Client, the pppd process cannot locate the appropriate module.
Couldn't open the /dev/ppp device: No such device or address Please load the ppp_generic kernel module.
Solution: Edit the
/etc/modprobe.d/modules.conf file and change
alias char-major-108 ppp
alias char-major-108 ppp_generic
If there is no alias included add
alias char-major-108 ppp_generic