Resilio Sync

From ArchWiki
Revision as of 14:40, 16 February 2014 by MichaelRpdx (talk | contribs) (→‎WebUI is not running on port 8888: add case where the webgui is not present on 7889+$UID)
Jump to navigation Jump to search

BitTorrent Sync (BTSync) is a file sharing system that relies on the BitTorrent protocol, and differs from other file sharing software in the connection type between devices. Instead of uploading the files to an online server, and then each device fetching them from the server itself, the file transfer is done directly from peer to peer, and therefore there is no limit on data storage and/or transfer speed.


BitTorrent Sync encrypts the traffic between devices with AES cypher and a 256-bit key created on the base of the secret — a random string (20 bytes or more) that is unique for every folder to be synchronized.


BitTorrent Sync uses a specific method for folder sharing, the 'secret': a random 21-byte key Base32-encoded.


When a device adds a folder for synchronization, a secret is generated. From now on, every device that wants to synchronize that folder must know the secret key.

The synchronization has no speed or size limits, as long as both devices have enough disk space.


btsyncAUR can be installed from the AUR. The package includes systemd service definitions for managing the btsync daemon.

Alternatively, the bare 'tar.gz' packaged executable is downloadable from the official website. The rest of this guide assumes that you are using the btsync AUR package.


The Linux client of BTSync does not use a typical GUI, instead it sets up a WebUI server accessible at localhost:8888. Shared folders can also be configured statically in a configuration file, but doing so disables the WebGUI.

Once installed, you'll first need to create a configuration file at ~/.config/btsync/btsync.conf, see #Configuration. When that is done, start and (if you want it to start on boot) enable the service:

# systemctl start btsync@user
# systemctl enable btsync@user

replacing user by the desired username. The service will run as the named user.

You can also run it as the btsync system user, just leave the @user part out:

# systemctl enable btsync
# systemctl start btsync

Configuration for this user is located at /etc/btsync.conf, and metadata is saved in /var/lib/btsync/ by default. You'll probably want to review the configuration settings, see below.


A sample configuration file can be created using btsync --dump-sample-config. You'll probably want to change some of the settings, including:

  • device_name
  • storage_path
  • webui/login
  • webui/password
Note: The storage_path setting defines where metadata will be saved, not the synced files themselves. Where synced files are saved is configured on a per-folder basis in the WebGUI.

Automatic config file creation

The btsync-autoconfigAUR package provides a systemd service (btsync-autoconfig@user.service) that, if enabled, triggers when btsync@user.service starts and creates a config file with default values if it does not already exist. The install script enables btsync-autoconfig@user.service by default.

btsync-autoconfig@user.service creates ~/.config/btsync/btsync.conf if it does not exist, and guesses some default values of the settings:

  • device_name: $USER@$HOSTNAME
  • storage_path: ~/.btsync
  • webui/login: $USER


Missing storage path

If you start the service but can't reach the WebUI, check the status of the btsync by entering systemctl status btsync@user.

A common error is Storage path specified in config file does not exist.. btsync-autoconfigAUR does generate a config file, but not the storage directory, do so by entering e.g. mkdir ~/.btsync.

WebUI is not running on port 8888

If the config file was generated by btsync-autoconfigAUR it will be configured with a different port. Rather than 8888, the port for the user's instance of btsync will be 7889 + $UID. If your $UID is "1000", the port will be 8889.

WebUI is not running on 7889 + $UID

The btsync-autoconfigAUR does not create $HOME/.btsync directory. This will cause the start up to fail.

Ignore some files/folders syncronization

If you have files in your sync folder that you don't want BitTorrent Sync to track, you can use .SyncIgnore. .SyncIgnore is a UTF-8 encoded .txt file that helps you specify single files, paths and rules for ignoring during the synchronization job. It supports '?' and '*' wildcard symbols.

Note that .SyncIgnore is applied only to the folder where it is contained and will not work with the files that have already been synced. If you add indexed files to .SyncIgnore, they will be deleted on other syncing devices. In order to avoid this:

  • Remove the folder from sync on all the devices.
  • Modify .SyncIgnore file on all of them so that it contains same info.
  • Re-add the modified folders.

See Also

Unofficial BitTorrent Sync FAQ

Official BitTorrent Sync FAQ