Difference between revisions of "Rt2x00 beta driver"

From ArchWiki
Jump to: navigation, search
(Extra utils for wep/wpa)
(merged into main page)
(35 intermediate revisions by 19 users not shown)
Line 1: Line 1:
#REDIRECT [[Wireless Setup#rt2x00]]
This page describes how you can make the new '''rt2x00''' Beta drivers work. This page '''does not''' describe the legacy '''rt2500''', '''rt2400''' and '''rt2570''' drivers derived from the original Ralink drivers.
At the time of this writing, only the '''rt2560''' PCI and PcCard chipsets ('''rt2500pci''' driver) are known to work in Open, WEP or WPA (PSK and EAP) mode. So far, there are no success stories with '''rt2400pci''', '''rt2500usb''' and '''rt61pci''' drivers. If you succeed in using these drivers, please add a comment here.
The '''rt2x00''' drivers are supposed to work with SMP kernels, but I did not test this myself. Please add comments here if you were able to use the driver with an SMP kernel.
There are still many issues with this driver. Many people experienced crappy speed. To help solve these issues, everyone who is willing to test the new driver should look at the [http://rt2x00.serialmonkey.com/phpBB2/viewforum.php?f=5 rt2x00 BETA Testing] section of the rt2x00 forums.
= Installing the driver =
The '''rt2x00 Beta 3''' (as posted in the AUR) and older version are known to '''NOT WORK'''. In order to have a working driver, you '''MUST''' use the new rewrite based on the DeviceScape stack. This new driver is (at the time of this writing) only available as a [http://rt2x00.serialmonkey.com/rt2x00-cvs-daily.tar.gz CVS snapshot]. To install the driver, unpack the driver, change to the '''rt2x00-cvs-2006XXXXXX''' directory and type
make install
There is a package for this in [unstable] that will be updated relatively frequently, however it is advised you use the latest snapshot. Grab the pkgbuild from CVS here: http://cvs.archlinux.org/cgi-bin/viewcvs.cgi/modules/rt2x00/?cvsroot=Unstable
= Using the driver =
== Setting the interface up ==
If you have module autoloading enabled, the drivers should be loaded automatically when you boot your machine or insert the device. If this doesn't work or autoloading is disabled, load the modules manually:
modprobe 80211
modprobe rate_control
modprobe $driver
where $driver is one of the following: '''rt2500pci''', '''rt2400pci''', '''rt2500usb''' or '''rt61pci'''.
When the driver is loaded, you will have two interfaces, wmaster0 and wlan0.
== Using the driver ==
In the case of these drivers, the order in which you configure them is important.
ifconfig wlan0 up
iwlist wlan0 scan
iwconfig wlan0 essid myessid
iwconfig wlan0 ap mybssid
Is the preferred, and most likely to work order of configuring the device. From there you can use '''ifconfig''' or '''dhcpcd''' to get an IP, and wep or wpa if needed.
= Extra utils for wep/wpa =
== wpa_supplicant ==
DeviceScape has its own '''dscape''' driver for wpa_supplicant. There are reports that wpa_supplicant also works with the '''wext''' driver, but I didn't test this. If you want to try the '''wext''' driver, you can use the '''wpa_supplicant''' package from the repos.
To use the '''dscape''' driver, you need to apply [http://kernel.org/pub/linux/kernel/people/jbenc/ieee80211-utils/wpa_supplicant/wpa_supplicant-0.4.7_dscape-02.patch this patch] to wpa_supplicant. You can also use the [http://www-users.rwth-aachen.de/thomas.baechler/arch/brain0/os/i686/wpa_supplicant-dscape-0.4.7-1.pkg.tar.gz wpa_supplicant-dscape package] from my repo.
== Using wpa_supplicant ==
For example, to use wpa_supplicant, try
/usr/sbin/wpa_supplicant -wB -Ddscape -ista0 -c/etc/wpa_supplicant.conf
Replace '''-Ddscape''' with '''-Dwext''' if you have chosen to use the stock arch wpa_supplicant package. Note that wpa_supplicant didn't work with hidden essid in my tests.
// TODO: someone please confirm that wpa_supplicant also successfully associates to open or wep-encrypted networks, I only tried WPA-PSK and read success reports about WPA-EAP
== Using WEP ==
WEP should work with the Wireless Extensions used by iwconfig, if not:
To enable WEP, use the following command:
dscape_crypt_conf -1tp "sta0" "ff:ff:ff:ff:ff:ff" WEP "$key"
where '''sta0''' is your wlan-interface and '''$key''' is the wep key. See
dscape_crypt_conf --help
for further help.
// TODO: Some please confirm that this works

Revision as of 22:44, 3 August 2013