Difference between revisions of "Rtl8187 wireless"

From ArchWiki
Jump to navigation Jump to search
(Using Ndiswrapper: Remove. Out of date and not needed anymore.)
(Compat-wireless-patched: Driver in the kernel. Patch is not needed.)
Line 76: Line 76:
  iwconfig wlan0 rts 2347
  iwconfig wlan0 rts 2347
== Compat-wireless-patched ==
The [http://wireless.kernel.org/ Linux Wireless] project provides frequent stable releases of patched drivers for the latest kernels. These drivers fix the "fixed-channel -1" issue, whilst providing better injection.
For further information and installation procedures please read the [[Wireless_Setup#compat-wireless-patched]] article.
=Misc Links=
=Misc Links=
*[http://wireless.kernel.org/ The Linux Wireless project]
*[http://wireless.kernel.org/ The Linux Wireless project]
*[http://aircrack-ng.org/doku.php?id=r8187 Aircrack-ng information for rtl8187 chips]
*[http://aircrack-ng.org/doku.php?id=r8187 Aircrack-ng information for rtl8187 chips]

Revision as of 09:28, 6 March 2013

This page describes how to get the rtl8187 wifi-driver working

The rtl8187 chip is made for usb-cards/dongles. It supports 802.11(a)/b/g and the following encryptions: WEP, WPA and WPA2. The rtl8187 driver is in the kernel now.

Using and testing the driver/Troubleshooting

Make sure that you have loaded the rtl8187 module with

modprobe rtl8187

Then run

dmesg | grep rtl8187

You should see some output like this

 usbcore: registered new interface driver rtl8187 

If you see that line everything should be OK

Using the driver

If everything is right, you should have two new interfaces: wlan0 and wmaster0 If you do not see wlan0 just run

ifconfig wlan0 up

To list all available wifi-networks just run

iwlist wlan0 scan

For more information about configuring your wifi-network see here: http://wiki.archlinux.org/index.php/Wireless_Setup#Setup_and_Boot

What to do if your connection always times out?

The open source driver suffers from a lot of tx excessive retries and invalid misc errors for some unknown reason, resulting in a lot of packet loss and it keeps disconnecting, some times instantly.

Adjusting with iwconfig options

Lowering the rate

The solution can be found in this thread: https://bbs.archlinux.org/viewtopic.php?pid=299642

Just set the rate to 5.5

iwconfig wlan0 rate 5.5M auto

Fixed option should ensure, however, it doesn't change the rate on its own, thus making the connection a bit more stable:

iwconfig wlan0 rate 5.5M fixed 

Alternativelly find the $POST_UP option and append the above options to your profile config file:

POST_UP="iwconfig wlan0 rate 5.5M fixed"

Try various rates until you get the optimal setting, with no disconnection. In this case 12Mbits, as shown bellow:

POST_UP="iwconfig wlan0 rate 12M fixed"

Now calling;

netfcg2 -c <wireless profile>



and choosing your profile works without extra commands.

Lowering the txpower

You can try lowering the transmit power as well. This may save power as well:

iwconfig wlan0 txpower 5

or even as low as 0. Valid settings are from 0 to 20, auto and off for the stock kernel driver.

Setting rts and fragmentation thresholds

Default iwconfig options have rts and fragmentation thresholds off. These options are particularly useful when there are many adjacent APs or in a noisy environment.

The minimum value for fragmentation value is 256 and maximum is 2346. In many windows drivers the maximum is the default value:

iwconfig wlan0 frag 2346

For rts minimum is 0, maximum is 2347. Once again windows drivers use maximum as the default:

iwconfig wlan0 rts 2347

Misc Links