Difference between revisions of "Rtl8187 wireless"

From ArchWiki
Jump to: navigation, search
(contained only general information, the driver itself "should just work" or the general informations are enough)
(25 intermediate revisions by 6 users not shown)
Line 1: Line 1:
{{i18n|Rtl8187 wireless}}
+
#REDIRECT [[Wireless Setup]]
[[Category:Wireless Networking (English)]]
 
 
 
This page describes how to get the '''rtl8187''' wifi-driver working
 
 
 
Note: The rtl8187 driver is in the kernel (thus the driver comes with the kernel26 package)
 
 
 
 
 
The rtl8187 chip is made for usb-cards/dongles
 
 
 
It supports 802.11(a)/b/g and the following encryptions:  WEP, WPA and WPA2
 
 
 
The driver's source is released under the GPL
 
 
 
=Using and testing the driver/Troubleshooting=
 
 
 
Make sure that you have loaded the rtl8187 module with
 
modprobe rtl8187
 
Then run
 
dmesg | grep rtl8187
 
You should see some output like this <pre> usbcore: registered new interface driver rtl8187 </pre>
 
If you see that line everything should be OK
 
 
 
== Using the driver ==
 
 
 
If everything is right, you should have two new interfaces: wlan0 and wmaster0
 
If you don't see wlan0 just run
 
ifconfig wlan0 up
 
 
 
To list all available wifi-networks just run
 
iwlist wlan0 scan
 
 
 
For more information about configuring your wifi-network see here: [http://wiki.archlinux.org/index.php/Wireless_Setup#Setup_and_Boot http://wiki.archlinux.org/index.php/Wireless_Setup#Setup_and_Boot]
 
 
 
== What to do if your connection always times out? ==
 
 
 
=== Method 1: Lowering the transfer rate manually ===
 
The solution can be found in this thread: http://bbs.archlinux.org/viewtopic.php?pid=299642
 
 
 
Just set the rate to 5.5
 
iwconfig wlan0 rate 5.5M auto
 
 
 
Actually this worked for a while but it would still start revving out, so making the last
 
item "fixed" ensures it does not spin.  Btw. If your wireless card has already gone into
 
meltdown issuing this command will get it working again.
 
 
 
iwconfig wlan0 rate 5.5M fixed
 
 
 
I have also tried setting this in the IWOPTS, but it does not seem to be taking, so now what I do until I get this sorted out is:
 
  netcfg2 -c <your wireless profile>
 
  iwconfig wlan0 rate 5.5M fixed
 
 
 
And then it never times out (at least for me)
 
 
 
Found the $POST_UP option, so appending this to your profile config
 
file, sets the rate correctly when using the netcfg tools.
 
 
 
    POST_UP="iwconfig wlan0 rate 5.5M fixed"
 
 
 
Actually for my card setting the rate higher still works, so now this line looks like:
 
 
 
    POST_UP="iwconfig wlan0 rate 12M fixed"
 
 
 
Now calling;
 
 
 
    netfcg2 -c <wireless profile>
 
or
 
  netcfg-menu
 
and choosing your profile works without extra commands.
 
 
 
=== Method 2: Aircrack-ng patched driver ===
 
{{Note|Note that this driver only works on kernel26}}
 
Another method that works for some users are the Aircrack-ng patches for the rtl8187 driver. This driver can be installed by the [http://aur.archlinux.org/packages.php?ID=15375 rtl8187-ng] package from [[AUR]].
 
 
 
=== Method 3: Using Ndiswrapper ===
 
If everything else fails, then you are left with using Ndiswrapper. Ndiswrapper takes Windows RTL8187 drivers and uses them to enable your card.
 
 
 
Symptoms which suggest you may have better luck with Ndiswrapper:
 
 
 
* "iwlist wlan0 scan" results are irregular and/or don't show some APs.
 
* Everything seems to be working, except the DHCP request, which may just time out.
 
 
 
1. Install ndiswrapper:
 
    pacman -S ndiswrapper
 
 
 
2. Download the Windows drivers:
 
    wget http://www.kuratkull.com/ndiswrapper/ndisdrivers.tar.gz
 
 
 
3. Extract the drivers:
 
    gzip -dc ndisdrivers.tar.gz | tar xf -
 
 
 
4. If you have the rtl8187 module loaded, then do this:
 
    rmmod rtl8187
 
It is suggested that you remove previous ndiswrapper drivers, if you have installed them.
 
    ndiswrapper -l
 
    ndiswrapper -r <drivername>
 
 
 
Also add "ndiswrapper" and "!rtl8187" to /etc/rc.conf under MODULES - this will stop rtl8187 from loading on boot, and will enable ndiswrapper to load on boot.
 
 
 
5. Install the driver:
 
If you have an older kernel(eg. older than 2.6.28.*), do:
 
 
 
    cd ./ndisdrivers/Win98-krnl24/
 
 
 
If you have a newer kernel (eg. 2.6.28.*), do:
 
 
    cd ./ndisdrivers/Win98seME-krnl28/
 
 
 
Proceed with:
 
    ndiswrapper -i net8187b.inf
 
    ndiswrapper -m
 
    modprobe ndiswrapper
 
 
 
Proceed to connect as you normally would.
 
 
 
=Misc Links=
 
*[http://rtl-wifi.sourceforge.net/ Project-page of the rtl-wifi driver project]
 

Revision as of 22:30, 3 August 2013

Redirect to: