Difference between revisions of "Rtl8187 wireless"

From ArchWiki
Jump to: navigation, search
m (Misc Links: Replaced link from the unrelated rtl-wifi project page to the Linux Wireless project one)
(contained only general information, the driver itself "should just work" or the general informations are enough)
(12 intermediate revisions by 4 users not shown)
Line 1: Line 1:
{{i18n|Rtl8187 wireless}}
#REDIRECT [[Wireless Setup]]
[[Category:Wireless Networking (English)]]
This page describes how to get the '''rtl8187''' wifi-driver working
Note: The rtl8187 driver is in the kernel (thus the driver comes with the linux package)
The rtl8187 chip is made for usb-cards/dongles
It supports 802.11(a)/b/g and the following encryptions:  WEP, WPA and WPA2
The driver's source is released under the GPL
=Using and testing the driver/Troubleshooting=
Make sure that you have loaded the rtl8187 module with
modprobe rtl8187
Then run
dmesg | grep rtl8187
You should see some output like this <pre> usbcore: registered new interface driver rtl8187 </pre>
If you see that line everything should be OK
== Using the driver ==
If everything is right, you should have two new interfaces: wlan0 and wmaster0
If you do not see wlan0 just run
ifconfig wlan0 up
To list all available wifi-networks just run
iwlist wlan0 scan
For more information about configuring your wifi-network see here: [http://wiki.archlinux.org/index.php/Wireless_Setup#Setup_and_Boot http://wiki.archlinux.org/index.php/Wireless_Setup#Setup_and_Boot]
= What to do if your connection always times out? =
The open source driver suffers from a lot of tx excessive retries and invalid misc errors for some unknown reason, resulting in a lot of packet loss and it keeps disconnecting, some times instantly.
==Adjusting with iwconfig options==
=== Lowering the rate ===
The solution can be found in this thread: http://bbs.archlinux.org/viewtopic.php?pid=299642
Just set the rate to 5.5
iwconfig wlan0 rate 5.5M auto
Fixed option should ensure, however, it doesn't change the rate on its own, thus making the connection a bit more stable:
iwconfig wlan0 rate 5.5M fixed
Alternativelly find the $POST_UP option and append the above options to your profile config file:
POST_UP="iwconfig wlan0 rate 5.5M fixed"
Try various rates until you get the optimal setting, with no disconnection. In this case 12Mbits, as shown bellow:
POST_UP="iwconfig wlan0 rate 12M fixed"
Now calling;
netfcg2 -c <wireless profile>
and choosing your profile works without extra commands.
=== Lowering the txpower ===
You can try lowering the transmit power as well. This may save power as well:
iwconfig wlan0 txpower 5
or even as low as 0. Valid settings are from 0 to 20, auto and off for the stock kernel driver.
=== Setting rts and fragmentation thresholds ===
Default iwconfig options have rts and fragmentation thresholds off. These options are particularly useful when there are many adjacent APs or in a noisy environment.
The minimum value for fragmentation value is 256 and maximum is 2346. In many windows drivers the maximum is the default value:
iwconfig wlan0 frag 2346
For rts minimum is 0, maximum is 2347. Once again windows drivers use maximum as the default:
iwconfig wlan0 rts 2347
== Compat-wireless-patched ==
The [http://wireless.kernel.org/ Linux Wireless] project provides frequent stable releases of patched drivers for the latest kernels. These drivers fix the "fixed-channel -1" issue, whilst providing better injection.
For further information and installation procedures please read the [[Wireless_Setup#compat-wireless-patched]] article.
== Using Ndiswrapper ==
If everything else fails, then you are left with using Ndiswrapper. Ndiswrapper takes Windows RTL8187 drivers and uses them to enable your card.
'''Install ndiswrapper'''
pacman -S ndiswrapper
'''Download the Windows drivers'''
wget [http://db.tt/4NB0HbF6 http://db.tt/4NB0HbF6]
'''Extract the drivers'''
unzip ndiswrapper.zip
'''Unload the rtl8187 module'''
modprobe -r rtl8187
'''Remove any previously installed drivers (if any)'''
ndiswrapper -r net8187b
'''Install the new drivers'''
ndiswrapper -i ./ndiswrapper/net8187b.inf
ndiswrapper -m
depmod -a
'''Make sure that it is installed'''
ndiswrapper -l
'''Try now loading the module'''
modprobe ndiswrapper
'''Kernel log shouldn't indicate any errors'''
dmesg | tail
'''If all steps are successful it should be visible now in the iwconfig interfaces list'''
'''Add ndiswrapper to the MODULES array in /etc/rc.conf'''
MODULES=(... powernow-k7 ndiswrapper ...)
'''Blacklist ''rtl8187'' in /etc/modprobe.conf.d/rtl8187.conf'''
blacklist rtl8187
Proceed to connect as you normally would.
{{Note|You may still have issues with disconnections, but in this case setting rates, rts and fragmentation thresholds actually work}}
=Misc Links=
*[http://wireless.kernel.org/ The Linux Wireless project]
*[http://aircrack-ng.org/doku.php?id=r8187 Aircrack-ng information for rtl8187 chips]

Revision as of 22:30, 3 August 2013

Redirect to: