Samsung Chromebook (ARM)

From ArchWiki
Revision as of 16:17, 2 August 2013 by Sbondaryev (talk | contribs) (Flashing non-verified U-boot)
Jump to: navigation, search

Template:Article summary start Template:Article summary text Template:Article summary heading Template:Article summary wiki Template:Article summary end

The Samsung Chromebook (model XE303C12) is a laptop intended work in the cloud. It provides a powerful Cortex-A15 Dual Core Exynos 5 processor at 1.7 GHz with Mali-T604 GPU, 2 GiB of DDR3, 16 GiB of internal flash storage, WiFi a/b/g/n, SD and USB ports, HDMI connector and a 11.6" display. It is visually like the MacBook Air 11. With stock firmware it runs a heavily modified Gentoo-Linux, which means that nearly every code is available at the Google's git. It is possible to install ArchLinux ARM (ALARM) on this device.

More information at dedicated pages by Google and Samsung.

Article Preface

This article is not meant to be an exhaustive setup guide and assumes that the reader has setup an Arch system before. Arch newbies are encouraged to read the Beginners' Guide if unsure how to preform standard tasks such as creating users, managing the system, etc.

Note: Support for the ARM architecture is provided on not through posts to the official Arch Linux Forum. Any posts related to ARM specific issues will be promptly closed per the Arch Linux Distrubution Support ONLY policy.

Installing Arch Linux ARM

See the instructions at the archlinuxarm site. More information will be added here in the near future.

Flashing non-verified U-boot

Warning: This process is very dangerous and shall not be carried out unless all the risks are known and understood. You are the only responsible of any damage which may occur

Boot process

The boot process of this Chromebook has several stages. The very first stages are burnt into the SoC (probably read-only although unconfirmed). Then, the SoC jumps to the starting of the 4 MiB SPI flash, which contains basically U-Boot.

This flash is split into a read-only half (first half) and read-write half. The read-only (RO) is loaded at the factory and contains several signature verifications (it is really a known-to-be-good U-Boot). The read-write (RW) is a signed U-Boot which also loads signed kernel and so on.

As you probably know (that's why you are reading this) you can load non-signed kernels by entering developer mode. But it has two drawbacks: you have to make a non-trivial process to install your bootloader and you have to hit Ctrl+D or Ctrl+U on every boot.

Removing RO protection

The good news is that you can disable the RO protection. The bad news is that you have to open your device. The recommended guide to open your Chromebook is the one at iFixit; stop at step 4, then jump to step 9. If you have a multimeter, ensure that after removal of the metallic sticker both parts of the ring are not in short-circuit.

Now you can write your U-Boot.

Getting nv U-Boot

Source: Media:

How to compile U-Boot


How to flash U-Boot


Booting from SD

If you ever screw things up by burning a wrong bootloader, there is a recovery mechanism. The SoC built-in bootloader (known as BL0 and BL1) can be configured to boot from SPI, USB, SD and probably other options. This is known because of the Arndale development board (and previous Exynos models behave the same as well).

This is configured at the factory to boot from SPI, but this is done with a bunch of resistors located at the bottom of the PCB (link to image). User (name) experimented and got the working configuration (link to image).

Warning: If you are unsure about how to short-circuit pads, you should definitely go away and experiment a bit with other electronics. A wrong short-circuit may permanently damage your board.

By short-circuiting the pads as per the diagram linked, your SoC will boot from SD. You have to (confirm this and complete the information) load a U-Boot with BL2 incorporated.

Related Links