Super Quick Git Guide
This isn't meant to be an all-encompassing guide by any means - it is meant to be a really quick walk-through on how to do some basic operations on the pacman codebase in git, such as submitting a patch.
For more extensive tutorials, check out the following:
- http://wiki.winehq.org/GitWine (talks a lot about maintaining patches)
In addition, all git commands have decent manpages to refer to. They can be reached one of two ways - for the git-add command, type 'man git-add' or 'git help add'.
The first step with git is cloning a remote repository. This is known in the CVS and SVN camps as checking out. GIT checkout has a different purpose, but that will be covered later.
To grab the pacman source into a new directory named 'pacman', run the following:
git clone git://projects.archlinux.org/pacman.git pacman
This will check out a local copy of the repository for you. This means you have the FULL history of the project on your computer, not just the most recent revision. This allows you to get work done even when offline, for example.
The first steps after cloning may be just to look around. If you have read the tutorials mentioned above, even if you do not understand everything in them, you will be much better off.
You will probably want to set up your name and email address for use in commit logs:
git-config user.name "Your Name" git-config user.email "email@example.com"
If you pass the '--global' flag to the above commands, the name and email will be stored in ~/.gitconfig, so will be used for all git projects unless overridden by a setting in the individual project.
To update your local repository with any new branches, run 'git pull'.
'git branch' will show you a list of branches. Initially, master is the only branch. However, if you pulled from a remote repo, you may have grabbed other branches- these can be seen with 'git branch -r'. Read the manpage for details.
When working with git, it is good practice to never do your work on the master branch. This should stay clean to allow you to run 'git pull' and ensure that conflicts do not happen on the update.
To create your own working branch, do the following (naming it whatever your heart desires):
git branch working git checkout working
Or compress the above into one command:
git checkout -b working
I highly recommend you read the man page for both of these commands.
Other Time Savers
If you use CVS or SVN and are used to 'co' being equivalent to 'checkout', try the following:
git-config --global alias.co "checkout"
'git-status' is highly helpful, it is recommended to read up on that.
Making a patch
Woo! You found a bug in pacman (what a surprise) and know how to fix it. Ensure you have your working branch checked out ('git checkout working'). Then edit the file(s) you need in order to make your changes. Compiling is a good idea to ensure your patch didn't break anything, and if it is a big change, running 'make check' is highly recommended.
So what do you do now? First, run 'git status'. You should see a list or even a few lists of files. The descriptions by each are a bit confusing, but you should be able to figure it out. GIT takes a different approach than CVS or SVN to committing changes- it doesn't commit a thing by default. You have to tell it what to commit, usually by running 'git add <filename>'. At this point, the file in its current state will be sent to a staging area for the commit. If you go back and change something in the file, you will have to git-add it again if you want the changes to be reflected in the commit.
To commit your patch to your branch:
git add <all edited files> git commit -s
When writing a commit message, keep the following in mind. The first line is used as a patch summary- keep it short and concise. Next, skip a line and type out a full description of what your patch does. By full, I don't mean long- if you described everything in the summary line, then don't even bother with a message. Finally, skip one more line and you will have your Signed-off-by. This should have been automatically added by passing the '-s' parameter to 'git commit'.
There is one more important step before submission. Because git is distributed, you don't have the most current version of the repository unless you go out and get it. In the easiest case, this is just running 'git pull'.
You also want to make sure your patches are based off the most recent revision, known as the 'head'. To do this, checkout your branch with your patches, and use the following command:
git rebase master
To visualize what the above command did, qgit can be very helpful.
To format a patch for email submission and review:
git format-patch master
This command will format all patches that make up the difference between your working branch and the master branch. They will be saved in the local directory; to store them elsewhere read up on the '-o' option.
Fixing your patch
So you sent off your patch to the ML and you got a few suggestions back. How does one fix it? Hopefully you did it on a branch and not the master branch, otherwise you are going to have a much tougher time. :)
If it was the last patch on a branch:
(edit the required files) git add <edited files> git commit --append -s
If it was deeper in your patch tree:
(ensure you are in the branch you wish to edit) git checkout -b tmp HEAD~<number> (where number is how far back you want to go, use 'git log' to determine) git reset HEAD^ (edit the required files) git commit -s -c ORIG_HEAD git rebase --onto tmp working~<number> working (replace working with your current working branch) git branch -D tmp
http://wiki.winehq.org/GitWine has good information on the above, that is where most of this came from. After fixing your patch, you will probably want to rebase it as described above, and then use format-patch to submit it again.
Commands you will definitely want to be knowledgeable on:
clone (only once!), branch, checkout, status, pull, fetch, diff, add, commit, rebase, format-patch
'git' itself is a wrapper script that calls the other commands. Thus, git-add can be called with either 'git add' or 'git-add'.
qgit in extra is a great GUI viewer for git repositories. In addition, read up on 'git-instaweb'.
Used to CVS or SVN-like behavior on commits, where all changes in the local tree are committed? Try using 'git-commit -a'.
- originally written by Dan McGee
- wikified by Roman Kyrylych