Swap on video ram
Warning: unless your X11 driver can be made to use less ram than exists (can be detected) your xserver will tend to crash when you try to use the same section of ram to store textures/framebuffer (glx or soemtimes qt) as swap. To be absolutely sure of stability, use an xorg driver that allows you to override videoram. At least the vga and radeon (xf86-video-ati) listen to an overide.
The fast memory on your graphics card (if you have one) can be used as general ram (actually swap) by using the MTD subsystem of the kernel. MTD is now included in kernel26.
Get a kernel version >= 184.108.40.206-6
When you are running a kernel with MTD modules, you have to load the modules specifying the pci address ranges that correspond to the ram on your video card.
check the ranges with
Then you look for the sections that name your video card as an example mine is here:
01:00.0 VGA compatible controller: ATI Technologies Inc RV350 AR [Radeon 9600] (prog-if 00 [VGA]) ubsystem: PC Partner Limited Unknown device 0830 ntrol: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- tatus: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- ency: 64 (2000ns min), Cache Line Size: 32 byteserrupt: pin A routed to IRQ 11 egion 0: Memory at e0000000 (32-bit, prefetchable) [size=256M] egion 1: I/O ports at c800 [size=256] egion 2: Memory at ff8f0000 (32-bit, non-prefetchable) [size=64K] ion ROM at ff8c0000 [disabled] [size=128K] ies: <access denied> 01:00.1 Display controller: ATI Technologies Inc RV350 AR [Radeon 9600] (Secondary) ubsystem: PC Partner Limited Unknown device 0831 ntrol: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- tatus: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- ency: 64 (2000ns min), Cache Line Size: 32 bytes egion 0: Memory at d0000000 (32-bit, prefetchable) [size=256M] egion 1: Memory at ff8e0000 (32-bit, non-prefetchable) [size=64K] ies: <access denied>
What's important is Region 0, (the biggest one)
The video card needs some ram to serve its normal purpose, so you need to do some calculations. The offsets are easy to calculate as powers of 2. The card uses the begining of the address range as framebuffer, textures etc. when it is limited (pretty sure about this, but maybe your driver could be different).
Example: total 2^28 bytes (256M) videoram, leaving 2^24 (32M) for the normal function (less will work fine) The start range, is 2^24 bytes more than the start of the pci address range shown by lspci -vvv.
The end is your total minus the amount you left for the card.
# for using vram as swap modprobe mtdblock slram map=VRAM,0xSTART RANGE,+0xWHAT IS USED mkswap /dev/mtdblock0 swapon /dev/mtdblock0 -p 10 #higher priority to be swapped to before disk
Xorg Driver Config
To keep X stable, you have to tell your video driver to take a small part of the videoram. In the Device section of your /etc/X11/xorg.conf the declaration
Section "Device" Driver "radeon" VideoRam 32768 EndSection
specifies that you use 32 MiB of ram. Other drivers might take the number for videoram as being in MiB (I think vga does), check manpages.