/usr/lib/sysctl.d/*.conf. If you had customized
/etc/sysctl.conf, you need to rename it as
/etc/sysctl.d/99-sysctl.conf. If you had e.g.
/etc/sysctl.d/foo, you need to rename is to
The sysctl preload/configuration file can be created at
/etc/sysctl.d/99-sysctl.conf. For systemd,
/usr/lib/sysctl.d/ are drop-in directories for kernel sysctl parameters. The naming and source directory decide the order of processing, which is important since the last parameter processed may override earlier ones. For example, parameters in a
/usr/lib/sysctl.d/50-default.conf will be overriden by equal parameters in
/etc/sysctl.d/50-default.conf and any configuration file processed later from both directories.
To load all configuration files manually, execute
# sysctl --system
which will also output the applied hierarchy. A single parameter file can also be loaded explicitly with
# sysctl -p filename.conf
The parameters available are those listed under
/proc/sys/. For example, the
kernel.sysrq parameter refers to the file
/proc/sys/kernel/sysrq on the file system. The
sysctl -a command can be used to display all currently available values.
/usr/lib/modules/$(uname -r)/build/Documentation/sysctl/. It is highly recommended reading these before changing sysctl settings.
Settings can be changed through file manipulation or using the
sysctl utility. For example, to temporarily enable the magic SysRq key:
# sysctl kernel.sysrq=1
# echo "1" > /proc/sys/kernel/sysrq
To preserve changes between reboots, add or modify the appropriate lines in
/etc/sysctl.d/99-sysctl.conf or another applicable parameter file in
/proc/sys/net/bridge/*depend on the
br_netfiltermodule. If it is not loaded at runtime (or after a reboot), those will silently not be applied. See Kernel modules#Loading
# reuse/recycle time-wait sockets net.ipv4.tcp_tw_reuse = 1 net.ipv4.tcp_tw_recycle = 1
TCP/IP stack hardening
The following specifies a parameter set to tighten network security options of the kernel for the IPv4 protocol and related IPv6 parameters where an equivalent exists.
For some usecases, for example using the system as a router, other parameters may be useful or required as well.
#### ipv4 networking and equivalent ipv6 parameters #### ## TCP SYN cookie protection (default) ## helps protect against SYN flood attacks ## only kicks in when net.ipv4.tcp_max_syn_backlog is reached net.ipv4.tcp_syncookies = 1 ## protect against tcp time-wait assassination hazards ## drop RST packets for sockets in the time-wait state ## (not widely supported outside of linux, but conforms to RFC) net.ipv4.tcp_rfc1337 = 1 ## sets the kernels reverse path filtering mechanism to value 1(on) ## will do source validation of the packet's recieved from all the interfaces on the machine ## protects from attackers that are using ip spoofing methods to do harm net.ipv4.conf.all.rp_filter = 1 net.ipv6.conf.all.rp_filter = 1 ## tcp timestamps ## + protect against wrapping sequence numbers (at gigabit speeds) ## + round trip time calculation implemented in TCP ## - causes extra overhead and allows uptime detection by scanners like nmap ## enable @ gigabit speeds net.ipv4.tcp_timestamps = 0 #net.ipv4.tcp_timestamps = 1 ## log martian packets net.ipv4.conf.all.log_martians = 1 ## ignore echo broadcast requests to prevent being part of smurf attacks (default) net.ipv4.icmp_echo_ignore_broadcasts = 1 ## ignore bogus icmp errors (default) net.ipv4.icmp_ignore_bogus_error_responses = 1 ## send redirects (not a router, disable it) net.ipv4.conf.all.send_redirects = 0 ## ICMP routing redirects (only secure) #net.ipv4.conf.all.secure_redirects = 1 (default) net.ipv4.conf.default.accept_redirects=0 net.ipv4.conf.all.accept_redirects=0 net.ipv6.conf.default.accept_redirects=0 net.ipv6.conf.all.accept_redirects=0
There are several key parameters to tune the operation of the virtual memory (VM) subsystem of the Linux kernel and the writeout of dirty data to disk. See the Linux kernel documentation for more information. For example:
vm.dirty_ratio = 3
- Contains, as a percentage of total available memory that contains free pages and reclaimable pages, the number of pages at which a process which is generating disk writes will itself start writing out dirty data.
vm.dirty_background_ratio = 2
- Contains, as a percentage of total available memory that contains free pages and reclaimable pages, the number of pages at which the background kernel flusher threads will start writing out dirty data.
As noted in the comments for the parameters, one needs to consider the total amount of RAM when setting these values:
vm.dirty_ratiodefaults to 10 (percent of RAM). Consensus is that 10% of RAM when RAM is say half a GB (so 10% is ~50 MB) is a sane value on spinning disks. But if the machine has much more RAM, say 16 GB (10% is ~1.6 GB), the percentage may be out of proportion as it becomes several seconds of writeback on spinning disks. A more sane value in this case is 3 (16*0.03 ~ 491 MB).
vm.dirty_background_ratiosimilarly, 5 (% of RAM) by default may be just fine for small memory values, but again, consider and adjust accordingly for the amount of RAM on a particular system.
When the kernel performs a resync operation of a software raid device it tries not to create a high system load by restricting the speed of the operation. Using sysctl it is possible to change the lower and upper speed limit.
# Set maximum and minimum speed of raid resyncing operations dev.raid.speed_limit_max = 10000 dev.raid.speed_limit_min = 1000
If mdadm is compiled as a module
md_mod, the above settings are available only after the module has been loaded. If the settings shall be loaded on boot via
/etc/sysctl.d, the module
md_mod may be loaded beforehand through
Small periodic system freezes
Set dirty bytes to small enough value (for example 4M):
vm.dirty_background_bytes = 4194304 vm.dirty_bytes = 4194304
Try to change
kernel.io_delay_type (x86 only):
- 0 - IO_DELAY_TYPE_0X80
- 1 - IO_DELAY_TYPE_0XED
- 2 - IO_DELAY_TYPE_UDELAY
- 3 - IO_DELAY_TYPE_NONE