Difference between revisions of "Systemd-boot"

From ArchWiki
Jump to navigation Jump to search
m (Adding boot entries: fixed edit before)
(Automatic copy on update of gummiboot: gummiboot is updated automatically now)
Line 77: Line 77:
efi            \shellx64.efi
efi            \shellx64.efi
== Automatic copy on update of gummiboot==
The copying of the {{ic|/usr/lib/gummiboot/gummiboot*.efi}} to the EFI System partition can be automated with systemd (as can eg. be done for the [[UEFI_Bootloaders#Sync_EFISTUB_Kernel_in_UEFISYS_partition_using_Systemd|EFISTUB kernel]]):
Description=Copy new version of Gummiboot to UEFISYS Partition
Description=Copy new version of Gummiboot to UEFISYS Partition
ExecStart=/bin/cp -f /usr/lib/gummiboot/gummibootx64.efi /boot/efi/EFI/gummiboot/gummiboot.efi
Change {{ic|gummibootx64.efi}} to {{ic|gummibootia32.efi}} for a 32-bit UEFI system.
After creating the files run:
# systemctl enable gummiboot_copy.path
# systemctl start gummiboot_copy.path
== Separate boot and EFI partitions ==
== Separate boot and EFI partitions ==

Revision as of 18:48, 11 March 2013

Gummiboot is a UEFI boot manager written by Kay Sievers and Harald Hoyer. It is simple to configure, but can only start EFI executables, the Linux kernel (with CONFIG_EFI_STUB enabled), grub.efi, and such.


In the following steps replace $esp with path to your EFI System Partition, which is normally mounted on /boot/efi (although some users have it on /boot directly).


Install gummiboot from [extra] and copy the bootloader to the EFI partition:

If you are on a 64-bit UEFI system:

# cp /usr/lib/gummiboot/gummibootx64.efi $esp/EFI/gummiboot/gummiboot.efi

If you are on a 32-bit UEFI system:

# cp /usr/lib/gummiboot/gummibootia32.efi $esp/EFI/gummiboot/gummiboot.efi

Then add it to the boot configuration: (only needs to be done once; skip this when upgrading)

# efibootmgr -c -d /dev/sdX -p Y -w -L "Gummiboot" -l '\EFI\gummiboot\gummiboot.efi'

where /dev/sdX is the drive and Y is the partition number of your UEFISYS partition.

Note: efibootmgr can be used only when already booted in UEFI mode. If you do not have another UEFI bootloader set up, you can either run gummiboot.efi from the UEFI Shell, or copy it to the "default" location $esp/EFI/boot/bootx64.efi for x86_64 systems.


The basic configuration is kept in $esp/loader/loader.conf, with just two possible configuration options:

  • default – default entry to select (without the .conf suffix); can be a wildcard like arch-*
  • timeout – menu timeout in seconds. If this is not set, the menu will only be shown when you hold the space key while booting.


default  arch
timeout  4

Note that both options can be changed in the boot menu itself, which will store them as EFI variables.

Adding boot entries


If you have separate partitions for /boot and /boot/efi, you must copy the kernel and initramfs to the EFI partition. Gummiboot does not support loading kernels from other partitions than itself. See UEFI_Bootloaders#Sync_EFISTUB_Kernel on how to automate this copy.

Gummiboot searches for boot menu items in $esp/loader/entries/*.conf – each file found must contain exactly one boot entry. The possible options are:

  • title – operating system name. Required.
  • version – kernel version, shown only when multiple entries with same title exist. Optional.
  • machine-id – machine identifier from /etc/machine-id, shown only when multiple entries with same title+version exist. Optional.
  • efi – EFI program to start; e.g. /vmlinuz-linux. Either this or linux (see below) is required.
  • options – Command-line options to pass to the EFI program. Optional, but you will need at least initrd=efipath and root=dev if booting Linux.

For Linux, you can specify linux path-to-vmlinuz and initrd path-to-initramfs; this will be automatically translated to efi path and options initrd=path – this syntax is only supported for convenience and has no differences in function.

An example entry for Arch Linux:

title          Arch Linux
linux          /vmlinuz-linux
initrd         /initramfs-linux.img
options        root=PARTUUID=14420948-2cea-4de7-b042-40f67c618660 ro

You can also add other EFI programs such as \EFI\arch\grub.efi or \EFI\Microsoft\Boot\Bootmgfw.efi (the Windows 7 boot manager). The EFI Shell, if installed, will be shown automatically.

title          UEFI Shell
efi            \shellx64.efi

Separate boot and EFI partitions

TODO: link my kernel-post-upgrade stuff, https://github.com/grawity/code/tree/master/os/arch

Inside the boot menu

TODO: document keybindings from http://freedesktop.org/wiki/Software/gummiboot


Transferring to new HDD causes breakage

Twice now I have transferred my installation from one disk to another, ESP included, and both times this broke my gummiboot setup. With a lot of trial and error, I have discovered that gummiboot does not like configuration files that have been tranfserred from one disk to another (I used rsync).

To solve this, delete the $ESP/loader directory and all of its contents, and recreate the necessary configuration files.

Though it has no additional info, here is my relevent forum thread.