Q: So what are the advantages of using grub2 instead of grub-gfx ? --Oliwer 23:44, 26 December 2008 (EDT)
A: Grub-gfx only adds the support for .xpm files, grub2 instead has builtin support for .tga, .jpeg/.jpg and .png formats. At some point the .tft files will also be supported (the ones that grub2-gxmenu supports) but I dunno when that's gonna happen. --Det 10:22, 24 February 2010 (EST)
The new stuff brought by 1.98 should probably be explained. --Det 10:57, 16 March 2010 (EDT)
E: I added a few "/etc/default/grub notes". The article only needs a bit expansion and the move from those notes I made to the actual instructions, anymore. --Det 13:44, 28 March 2010 (EDT)
E2: OK, done. I changed the notes to the actual instructions and removed the Expansion flag. If somebody feels that the other stuff too, such as what's in /etc/grub.d/* should be mentioned here, you are free to re-add the flag. I did some other stuff too, which you can check from the page history if you are interested. The only problem is that I'm still that stupid that I test the changes by updating the page itself, which makes the page history go nuts. Just give me some time to get used to the magic *Show preview* button :). --Det 15:58, 8 April 2010 (EDT)
Upgrading from grub 0.97 to grub2 - MBR
To fix the problem described on section GRUB2#Other you can remove grub 0.97 from MBR by following command:
dd if=/dev/zero of=/dev/sdX bs=446 count=1
where /dev/sdX is hard disk with grub installed in MBR (I have no idea if that works when you have grub installed on partition instead of hd, like /dev/sda1).
It is good idea to create backup of bootloader before that by executing:
dd if=/dev/sdX of=your/backup.img bs=446 count=1
After that you can install grub2 on MBR, and it works (hopefully) without any dirty hacks.
Make up your mind on when to modprobe dm-mod
@Skodabenz & NTia89
- On Feb 17 NTia89 took the time to suggest the probing of dm-mod at the beginning of the Installation section, not deleting it from the section below but just inserting a note. On Mar 15 Skodabenz only removed the modprobe command inserted by NTia89, but not the related note, so this leaves the article inaccurate on stating when to load dm-mod. I think either the note should be removed (if Skodabenz is right), or the modprobe dm-mod command should be moved to the beginning of the Installation section (if NTia89 is right)). I cannot test this at the moment. -- Kynikos 14:13, 15 March 2011 (EDT)
@Kynikos: Whether grub2 install happens during Arch Linux installation or in a existing system, dm-mod (device-mapper module) needs to be loaded for the sake of grub-setup utility. Even during Arch Linux installation, the user has to anyway go to one of the bootloader installation section where dm-mod loading comes again. Therefore i do not think it is appropriate to move it to the beginning of the Installation section since it is not specific to Arch Linux installation. Also where is the 'related note' you are talking about? -- Keshav P R 17:37, 16 March 2011 (EDT)
- Perfectly explained, thanks. The "related note" is this one I've just removed (see diff); it was added by NTia89 when he edited the article. -- Kynikos 19:53, 16 March 2011 (EDT)
Is there any reason why grub should be installed to /boot/efi/efi/grub and not to /boot/efi? UEFI wants to have the efi-image unter <EFI SYSTEM PARTITION>/efi/name, so /boot/efi/grub should do the trick. Additionally, mounting (e.g.) /dev/sda1 to /boot/efi and just placing the grub there will possibly conflict with having a LVM+LUKS setup, where /boot will then be encrypted. At the moment I'm running a funtoo installation on a thinkpad x121e with /dev/sda1 (200MB, fat32, sectors 1 - 201) mounted to /boot and /dev/sda2 being a LUKS encrypted system. /boot contains the bzImage and /boot/efi/boot/bootx64.efi is the grub-image.
Note: there should possibly be a section/table here containing information what firmware expects what name. having /boot/efi/grub/grub.efi didn't work for me, and as noted in the thinkwiki for an x220, /boot/efi/boot/bootx64.efi works fine. --Rochus 13:59, 16 August 2011 (EDT)
@Rochus: You have mounted your EFISYS partition at /boot ir you are using same part as both EFISYS and /boot and it is FAT32 formatted. The actual path is <EFI_SYS_PART>/efi/grub/grub.efi wherein <EFI_SYS_PART> is usually /boot/efi or in your case /boot itself.
But I do not understand your argument about mounting EFISYS at /boot/efi conflicting with LVM+LUKS. I don't have such a config in my system to understand what you are coming to say. <EFI_SYS_PART>/efi/boot/bootx64.efi is just a fallback path incase there's no boot entry in UEFI Boot Manager (see efibootmgr section). I already mentioned in the article that "If you have mounted EFISYS part at a different mountpoint, replace /boot/efi with that mountpoint in all the commands". I suppose that explains it. It is better to have /boot separate from EFISYS partition. I have /dev/sda1 as 200 MiB FAT32 EFISYS mounted at /boot/efi and /dev/sda3 as 400 MiB ext4 /boot part. For /boot/efi/grub/grub.efi to work you have to add a boot entry to grub.efi in the UEFI Boot Manager using efibootmgr utility. -- Keshav P R 23:15, 28 August 2011 (IST)
grub-mkconfig and UEFI
The grub-mkconfig script seems to be hardcoded to have /boot/grub as the grub install. Is the best answer for this to mount /efi/grub as /boot/grub or edit the script?