Talk:Network configuration

From ArchWiki
Revision as of 09:49, 24 February 2013 by Fengchao (talk | contribs) (Static IP)
Jump to navigation Jump to search

Set host name/IP

Shouldn't the hosts file include the local static IP address and computer name along with the loopback version? - KitchM 02:54, 1 June 2009 (EDT)

Does anybody have more info on this? - Aaahaaap 11:22, 2 November 2009 (EST)
I sure wish someone did. - KitchM 18:43, 2 November 2009 (EST)

Troubleshooting Ping

The section entitled Troubleshooting should probably include a section to address the problem of ping not working correctly. - KitchM 02:36, 1 June 2009 (EDT)

Needs cleanup

The hostname portion fails to explain whether or not the quotation marks around the name is required. The next example does not have them. Either way, it must be explained.

We are left with another question; is it listed in hosts under the loopback address only, or also included in the standard IP address?

Under IP Aliasing we are missing the explanation of what it is and why one would use it.

Regarding the TCP window scaling, what does the following phrase mean: "Or you can try to remove one of your RAM sticks (yes, sir)."

Let's clean this up, everyone.

Thanks. - KitchM 22:38, 27 November 2009 (EST)


Shouldn't that be Configuring The Network, or Network Configuration? - KitchM 00:50, 25 December 2009 (EST)

In fact, wouldn't "Network Configuration" be better because Network would be the first and most common sense search item? _ KitchM 12:36, 8 February 2010 (EST)

Perhaps "Network" would be the best title, then, since this article deals primarily with using the "network" daemon. -- pointone 11:37, 26 February 2010 (EST)
You think so? I don't know. Doesn't it have more to do with network setup in general? - KitchM 00:14, 5 March 2010 (EST)
Page renamed. Close. -- Fengchao (talk) 09:45, 24 February 2013 (UTC)

Carrier Detect

This code can be used in /etc/rc.d/network to skip dhcp on interfaces without carriers:

 if [[ "$ifcfg" = "dhcp" ]]; then
     carrier=`cat /sys/class/net/$ifname/carrier`
     if [[ $carrier -eq "1" ]]; then
         # remove the .pid file if it exists
         /bin/rm -f /var/run/dhcpcd-${1}.pid >/dev/null 2>&1
         /bin/rm -f /var/run/dhcpcd-${1}.cache >/dev/null 2>&1
         /sbin/dhcpcd $DHCPCD_ARGS ${1}
         echo "No carrier on $ifname"
     /sbin/ifconfig $ifcfg
Close. Arch do not use rc.d anymore. -- Fengchao (talk) 09:46, 24 February 2013 (UTC)

Static IP

The indications given for the static ip configuration do not work for me. Concretely, the gateway config gives me problems. There should be another way of doing it.

There is no doubt that one has to be extremely careful to follow the directions, keeping in mind that the directions are based on a clean install. Missing any step, or having some pre-existing setting that conflicts will cause the failure.
This is a perfect place for feedback so we can get this completely goof-proof. Can you verify that you followed the exact steps described here? Can you give us a list of which you did and where you skipped something that didn't apply? Don't forget the hardware arrangement of your network. I think your information would help us polish this a little and make it more accurate. - KitchM 21:21, 11 November 2010 (EST)
you might have to get an ip via dhcp, then assign yourself a static ip in the router settings and make your computer use that with no dhcp - it really depends on the type of router thestinger 21:32, 11 November 2010 (EST)
There is no doubt that the suggestion you offered might work in one particular situation. However, we don't have enough information to make that determination yet, nor do we have any information to improve the article, which is the point here. - KitchM 22:59, 11 November 2010 (EST)
Old method changed to systemd service. Close this old report. -- Fengchao (talk) 09:49, 24 February 2013 (UTC)